参数资料
| 型号： | AD5750BCPZ-REEL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 25/36页 |
| 文件大小： | 0K |
| 描述： | IC CURR/VOLT OUT DVR 32LFCSP |
| 标准包装： | 5,000 |
| 放大器类型： | 仪表 |
| 电路数： | 1 |
| 转换速率： | 2 V/µs |
| 电流 - 电源： | 5.2mA |
| 电流 - 输出 / 通道： | 24mA |
| 电压 - 电源，单路/双路(±)： | ±10.8 V ~ 26.4 V |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-VFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 32-LFCSP-VQ（5x5） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页当前第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
AD5750/AD5750-1
Rev. C | Page 31 of 36
APPLICATIONS INFORMATION
TRANSIENT VOLTAGE PROTECTION
The AD5750/AD5750-1 contain ESD protection diodes that
prevent damage from normal handling. The industrial control
environment can, however, subject I/O circuits to much higher
transients. To protect the AD5750/AD5750-1 from excessively
high voltage transients, external power diodes and a surge
current limiting resistor may be required, as shown in Figure 56.
The constraint on the resistor value is that during normal opera-
tion the output level at IOUT must remain within its voltage
compliance limit of AVDD 2.75 V and the two protection
diodes and resistor must have appropriate power ratings.
Further protection can be added with transient voltage
suppressors if needed.
IOUT
AVDD
AVSS
AD5750/AD5750-1
RP
RLOAD
0
72
68
-0
50
Figure 56. Output Transient Voltage Protection
THERMAL CONSIDERATIONS
It is important to understand the effects of power dissipation on
the package and how it affects junction temperature. The internal
junction temperature should not exceed 125°C. The AD5750/
AD5750-1 are packaged in a 32-lead, 5 mm × 5 mm LFCSP
package. The thermal impedance, θJA, is 28°C/W. It is important
that the devices are not operated under conditions that cause
the junction temperature to exceed its junction temperature.
Worst-case conditions occur when the AD5750/AD5750-1 are
operated from the maximum AVDD (26.4 V) and driving the
maximum current (24 mA) directly to ground. The quiescent
current of the AD5750/AD5750-1 should also be taken into
account, nominally ~4 mA.
The following calculations estimate maximum power dissipa-
tion under these worst-case conditions, and determine
maximum ambient temperature based on this:
Power Dissipation = 26.4 V × 28 mA = 0.7392 W
Temp Increase = 28°C × 0.7392 W = 20.7°C
Maximum Ambient Temp = 125°C 20.7°C = 104.3°C
These figures assume proper layout and grounding techniques
are followed to minimize power dissipation, as outlined in the
Layout Guidelines section.
LAYOUT GUIDELINES
In any circuit where accuracy is important, careful consideration
of the power supply and ground return layout helps to ensure the
rated performance. The PCB on which the AD5750/AD5750-1
are mounted should be designed so that the AD5750/AD5750-1
lie on the analog plane.
The AD5750/AD5750-1 should have ample supply bypassing of
10 μF in parallel with 0.1 μF on each supply located as close to
the package as possible, ideally right up against the device. The
10 μF capacitors are the tantalum bead type. The 0.1 μF capaci-
tor should have low effective series resistance (ESR) and low
effective series inductance (ESI) such as the common ceramic
types, which provide a low impedance path to ground at high
frequencies to handle transient currents due to internal logic
switching.
In systems where there are many devices on one board, it is often
useful to provide some heat sinking capability to allow the power
to dissipate easily.
AD5750/AD5750-1
AVSS
PLANE
BOARD
07
26
8-
05
1
Figure 57. Paddle Connection to Board
The AD5750/AD5750-1 have an exposed paddle beneath the
device. Connect this paddle to the AVSS supply for the part. For
optimum performance, special considerations should be used to
design the motherboard and to mount the package. For enhanced
thermal, electrical, and board level performance, the exposed
paddle on the bottom of the package should be soldered to the
corresponding thermal land paddle on the PCB. Thermal vias
should be designed into the PCB land paddle area to further
improve heat dissipation.
The AVSS plane on the device can be increased (as shown in
Figure 57) to provide a natural heat sinking effect.
相关PDF资料 |
PDF描述 |
|---|---|
| RNCP0603FTD274R | RES 274 OHM 1% 0603 SMD |
| TSW-137-26-G-D | CONN HEADER 74POS .100" DL GOLD |
| 77313-119-04LF | BERGSTIK |
| ISL28325FUZ-T7A | IC OP AMP 1.2MHZ DUAL LP 8MSOP |
| Y17455K00000T9R | RES 5.0K OHM .25W .01% Z-FOIL SM |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD5750BCPZ-REEL7 | 功能描述:IC CURR/VOLT OUT DVR 32LFCSP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:73 系列:Over-The-Top® 放大器类型:通用 电路数:4 输出类型:满摆幅 转换速率:0.07 V/µs 增益带宽积:200kHz -3db带宽:- 电流 - 输入偏压:1nA 电压 - 输入偏移:285µV 电流 - 电源:50µA 电流 - 输出 / 通道:25mA 电压 - 电源，单路/双路(±):2 V ~ 44 V，±1 V ~ 22 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-WFDFN 裸露焊盘 供应商设备封装:16-DFN-EP（5x3） 包装:管件 |
| AD5751 | 制造商:AD 制造商全称:Analog Devices 功能描述:Industrial Current/Voltage Output Driver |
| AD5751ACPZ | 功能描述:IC CURR/VOLT OUT DVR 32LFCSP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:2,500 系列:Excalibur™ 放大器类型:J-FET 电路数:1 输出类型:- 转换速率:45 V/µs 增益带宽积:10MHz -3db带宽:- 电流 - 输入偏压:20pA 电压 - 输入偏移:490µV 电流 - 电源:1.7mA 电流 - 输出 / 通道:48mA 电压 - 电源，单路/双路(±):4.5 V ~ 38 V，±2.25 V ~ 19 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SOIC 包装:带卷 (TR) |
| AD5751ACPZ | 制造商:Analog Devices 功能描述:IC CURRENT/VOLTAGE O/P DRIVER LFCSP-32 |
| AD5751ACPZ-REEL7 | 功能描述:IC I/V OUTPUT DRIVER 60V 32LFCSP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:50 系列:- 放大器类型:J-FET 电路数:2 输出类型:- 转换速率:3.5 V/µs 增益带宽积:1MHz -3db带宽:- 电流 - 输入偏压:30pA 电压 - 输入偏移:2000µV 电流 - 电源:200µA 电流 - 输出 / 通道:- 电压 - 电源，单路/双路(±):7 V ~ 36 V，±3.5 V ~ 18 V 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:8-DIP（0.300"，7.62mm） 供应商设备封装:8-PDIP 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。