- 您现在的位置：买卖IC网 > PDF目录11674 > AD598JRZ (Analog Devices Inc)IC LVDT SGNL COND OSC/REF 20SOIC PDF资料下载
参数资料
| 型号： | AD598JRZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 2/16页 |
| 文件大小： | 0K |
| 描述： | IC LVDT SGNL COND OSC/REF 20SOIC |
| 标准包装： | 1 |
| 类型： | 信号调节器 |
| 输入类型： | 电压 |
| 输出类型： | 电压 |
| 接口： | LVDT |
| 电流 - 电源： | 15mA |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 20-SOIC W |
| 包装： | 管件 |
| 产品目录页面： | 791 (CN2011-ZH PDF) |
PROVING RING-WEIGH SCALE
Figure 20 shows an elastic member (steel proving ring) com-
bined with an LVDT to provide a means of measuring very
small loads. Figure 19 shows the electrical circuit details.
The advantage of using a Proving Ring in combination with an
LVDT is that no friction is involved between the core and the
coils of the LVDT. This means that weights can be measured
without confusion from frictional forces. This is especially im-
portant for very low full-scale weight applications.
EXC 1
EXC 2
LEV 1
LEV 2
FREQ 1
FREQ 2
B1 FILT
B2 FILT
OFFSET 1
OFFSET 2
SIG REF
SIG OUT
FEEDBACK
OUT FILT
A1 FILT
A2 FILT
AD598
C3
C4
SCHAEVITZ HR050
LVDT
6.8
F
0.1
F
0.1
F
6.8
F
–15V
SIGNAL
REFERENCE
15V
+
–VS
R
L
VOUT
+VS
1
2
3
4
5
6
7
8
9
10
11
12
13
14
16
15
17
18
19
20
1
F
634k
10k
0.33
F
0.1
F
C2
0.1
F
C1
0.015
F
VA
VB
Figure 19. Proving Ring-Weigh Scale Circuit
FORCE/LOAD
PROVING
RING
LVDT
CORE
Figure 20. Proving Ring-Weigh Scale Cross Section
Although it is recognized that this type of measurement system
may best be applied to weigh very small weights, this circuit was
designed to give a full-scale output of 10 V for a 500 lb weight,
using a Morehouse Instruments model 5BT Proving Ring. The
LVDT is a Schaevitz type HR050 (
±50 mil full scale). Although
this LVDT provides
±50 mil full scale, the value of R2 was cal-
culated for d =
±30 mil and V
OUT equal to 10 V as in Step 9 of
the design procedures.
The 1
F capacitor provides extra filtering, which reduces noise
induced by mechanical vibrations. The other circuit values were
calculated in the usual manner using the design procedures.
This weigh-scale can be designed to measure tare weight simply
by putting in an offset voltage by selecting either R3 or R4 (as
shown in Figures 7 and 12). Tare weight is the weight of a con-
tainer that is deducted from the gross weight to obtain the net
weight.
The value of R3 or R4 can be calculated using one of two sepa-
rate methods. First, a potentiometer may be connected between
Pins 18 and 19 of the AD598, with the wiper connected to
–VSUPPLY. This gives a small offset of either polarity; and the
value can be calculated using Step 10 of the design procedures.
For a large offset in one direction, replace either R3 or R4 with
a potentiometer with its wiper connected to –VSUPPLY.
The resolution of this weigh-scale was checked by placing a 100
gram weight on the scale and observing the AD598 output sig-
nal deflection on an oscilloscope. The deflection was 4.8 mV.
The smallest signal deflection which could be measured on the
oscilloscope was 450
V which corresponds to a 10 gram
weight. This 450
V signal corresponds to an LVDT displace-
ment of 1.32 microinches which is equivalent to one tenth of the
wave length of blue light.
The Proving Ring used in this circuit has a temperature coeffi-
cient of 250 ppm/
°C due to Young’s Modulus of steel. By put-
ting a resistor with a temperature coefficient in place of R2 it is
possible to temperature compensate the weigh-scale. Since the
steel of the Proving Ring gets softer at higher temperatures, the
deflection for a given force is larger, so a resistor with a negative
temperature coefficient is required.
SYNCHRONOUS OPERATION OF MULTIPLE LVDTS
In many applications, such as multiple gaging measurement, a
large number of LVDTs are used in close physical proximity. If
these LVDTs are operated at similar carrier frequencies, stray
magnetic coupling could cause beat notes to be generated. The
resulting beat notes would interfere with the accuracy of mea-
surements made under these conditions. To avoid this situation
all the LVDTs are operated synchronously.
The circuit shown in Figure 21 has one master oscillator and
any number of slaves. The master AD598 oscillator has its fre-
quency and amplitude programmed in the usual manner via R1
and C2 using Steps 6 and 7 in the design procedures. The slave
AD598s all have Pins 6 and 7 connected together to disable
their internal oscillators. Pins 4 and 5 of each slave are con-
nected to Pins 2 and 3 of the master via 15 k
resistors, thus
setting the amplitudes of the slaves equal to the amplitude of the
master. If a different amplitude is required the 15 k
resistor
values should be changed. Note that the amplitude scales lin-
early with the resistor value. The 15 k
value was selected be-
cause it matches the nominal value of resistors internal to the
circuit. Tolerances of 20% between the slave amplitudes arise
due to differing internal resistors values, but this does not affect
the operation of the circuit.
Note that each LVDT primary is driven from its own power am-
plifier and thus the thermal load is shared between the AD598s.
There is virtually no limit on the number of slaves in this circuit,
since each slave presents a 30 k
load to the master AD598
power amplifier. For a very large number of slaves (say 100 or
more) one may need to consider the maximum output current
drawn from the master AD598 power amplifier.
REV. A
–10–
AD598–Applications
相关PDF资料 |
PDF描述 |
|---|---|
| 221185-2 | CONN PLUG BNC 75 OHM DUAL CRIMP |
| AD698APZ | IC LVDT SIGNAL COND 28-PLCC |
| 221185-8 | CONN PLUG BNC 75 OHM DUAL CRIMP |
| AD693AD | IC SGNL COND 4-20MA TX 20-CDIP |
| AD9824KCPZ | IC CCD SIGNAL PROC 14BIT 48LFCSP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD598JRZ | 制造商:Analog Devices 功能描述:Signal Conditioner IC |
| AD598SD/883B | 制造商:Analog Devices 功能描述:LVDT Signal Conditioner 20-Pin SBCDIP 制造商:Analog Devices 功能描述:LVDT IC - Rail/Tube 制造商:Analog Devices 功能描述:MIL LVDT SIG COND 20-CDIP 制造商:Analog Devices 功能描述:IC SIGNAL CONDITIONER 制造商:Analog Devices Inc. 功能描述:Interface - Specialized IC LVDT Signal Conditioner |
| AD598SD/883B-MOOG | 制造商:Analog Devices 功能描述: |
| AD5T | 制造商:Opto 22 功能描述:I/O Module; 5 VDC @ 170 mA; 0 to degC; UL, CSA, CE Certified 制造商:Opto 22 功能描述:I/O MODULE 制造商:Opto 22 功能描述:I/O MODULE; Leaded Process Compatible:No; Peak Reflow Compatible (260 C):No; No. of Analog Inputs:1; No. of Digital Outputs:1; No. of Outputs:1; Resolution:12 Bits; Signal Input Type:J Thermocouple ;RoHS Compliant: No 制造商:Opto 22 功能描述:Access Module Analog J Thermocouple Input Isolated Ad5T |
| AD6 | 功能描述:保险丝 6A 415V AC / 250V DC RoHS:否 制造商:Littelfuse 产品:Surface Mount Fuses 电流额定值:0.5 A 电压额定值:600 V 保险丝类型:Fast Acting 保险丝大小/组:Nano 尺寸:12.1 mm L x 4.5 mm W 安装风格: 端接类型:SMD/SMT 系列:485 |
发布紧急采购，3分钟左右您将得到回复。