参数资料
| 型号： | AD711KRZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 3/16页 |
| 文件大小： | 0K |
| 描述： | IC OPAMP BIFET PREC 25MA 8SOIC |
| 产品培训模块： | Op Amp Basics |
| 标准包装： | 98 |
| 放大器类型： | J-FET |
| 电路数： | 1 |
| 转换速率： | 20 V/µs |
| -3db带宽： | 4MHz |
| 电流 - 输入偏压： | 15pA |
| 电压 - 输入偏移： | 200µV |
| 电流 - 电源： | 2.5mA |
| 电流 - 输出 / 通道： | 25mA |
| 电压 - 电源，单路/双路(±)： | 9 V ~ 36 V，±4.5 V ~ 18 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 管件 |
| 产品目录页面： | 773 (CN2011-ZH PDF) |
REV. E
AD711
–11–
DRIVING A LARGE CAPACITIVE LOAD
The circuit in Figure 13 employs a 100
W isolation resistor which
enables the amplifier to drive capacitive loads exceeding 1500 pF;
the resistor effectively isolates the high frequency feedback from
the load and stabilizes the circuit. Low frequency feedback is
returned to the amplifier summing junction via the low pass
filter formed by the 100
W series resistor and the load capaci-
tance, CL. Figure 14 shows a typical transient response for
this connection.
RL
INPUT
+VS
–VS
0.1 F
CL
0.1 F
TYPICAL CAPACITANCE
LIMIT FOR VARIOUS
LOAD RESISTORS
RL
CL UP TO
2k
1500pF
10k
1500pF
20k
1000pF
4.99k
AD711
100
30pF
4.99k
OUTPUT
Figure 13. Circuit for Driving a Large Capacitive Load
Figure 14. Transient Response RL = 2 k
W, CL = 500 pF
ACTIVE FILTER APPLICATIONS
In active filter applications using op amps, the dc accuracy of the
amplifier is critical to optimal filter performance. The amplifier’s
offset voltage and bias current contribute to output error. Offset
voltage will be passed by the filter and may be amplified to produce
excessive output offset. For low frequency applications requiring
large value input resistors, bias currents flowing through these
resistors will also generate an offset voltage.
In addition, at higher frequencies, an op amp’s dynamics must
be carefully considered. Here, slew rate, bandwidth, and open-loop
gain play a major role in op amp selection. The slew rate must
be fast as well as symmetrical to minimize distortion. The amplifier’s
bandwidth in conjunction with the filter’s gain will dictate the
frequency response of the filter.
The use of a high performance amplifier such a s the AD711
will minimize both dc and ac errors in all active filter applica-
tions.
SECOND ORDER LOW PASS FILTER
Figure 15 depicts the AD711 configured as a second order
Butterworth low pass filter. With the values as shown, the corner
frequency will be 20 kHz; however, the wide bandwidth of the
AD711 permits a corner frequency as high as several hundred
kilohertz. Equations for component selection are shown below.
R1 = R2 = user selected (typical values: 10 k
W – 100 kW)
(4)
C1
=
1.414
(2
p)( fcutoff)(R1)
, C2
=
0.707
(2
p)( fcutoff)(R1)
(5)
Where:
C1 and C2 are in farads.
VOUT
+15V
–15V
0.1 F
AD711
VIN
C2
280pF
R2
20k
R1
20k
C1
560pF
Figure 15. Second Order Low Pass Filter
An important property of filters is their out-of-band rejection.
The simple 20 kHz low pass filter shown in Figure 15, might be
used to condition a signal contaminated with clock pulses or
sampling glitches which have considerable energy content at
high frequencies.
The low output impedance and high bandwidth of the AD711
minimize high frequency feedthrough as shown in Figure 16.
The upper trace is that of another low-cost BiFET op amp
showing 17 dB more feedthrough at 5 MHz.
Figure 16.
voltage. If the A/D conversion speed is not excessive and the
bandwidth of the amplifier is sufficient, the amplifier’s output
will return to the nominal value before the converter makes its
comparison. However, many amplifiers have relatively narrow
bandwidth yielding slow recovery from output transients. The
AD711 is ideally suited to drive high speed A/D converters since
it offers both wide bandwidth and high open-loop gain.
a. Source Current = 2 mA
b. Sink Current = 1 mA
Figure 12. ADC Input Unity Gain Buffer Recovery Times
相关PDF资料 |
PDF描述 |
|---|---|
| PBC11SADN | CONN HEADER .100 SINGL STR 11POS |
| OP213FPZ | IC OPAMP GP 3.4MHZ DUAL LN 8DIP |
| OP213FSZ | IC OPAMP GP 3.4MHZ DUAL LN SOIC |
| PEC11SFDN | CONN HEADER .100 SINGL STR 11POS |
| 1.5SMC47AT3G | TVS 1500W 47V UNIDIRECT SMC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD711KRZ | 制造商:Analog Devices 功能描述:IC OP-AMP 4MHZ 20V/ ((NW)) 制造商:Analog Devices 功能描述:IC, OP-AMP, 4MHZ, 20V/ us, SOIC-8 |
| AD711KRZ-REEL | 功能描述:IC OPAMP BIFET PREC 25MA 8SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:50 系列:LinCMOS™ 放大器类型:通用 电路数:4 输出类型:- 转换速率:0.05 V/µs 增益带宽积:110kHz -3db带宽:- 电流 - 输入偏压:0.7pA 电压 - 输入偏移:210µV 电流 - 电源:57µA 电流 - 输出 / 通道:30mA 电压 - 电源，单路/双路(±):3 V ~ 16 V，±1.5 V ~ 8 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SOIC 包装:管件 产品目录页面:865 (CN2011-ZH PDF) 其它名称:296-1834296-1834-5 |
| AD711KRZ-REEL7 | 功能描述:IC OPAMP BIFET PREC 25MA 8SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 其它有关文件:Automotive Product Guide 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 放大器类型:通用 电路数:1 输出类型:满摆幅 转换速率:3 V/µs 增益带宽积:10MHz -3db带宽:- 电流 - 输入偏压:1pA 电压 - 输入偏移:70µV 电流 - 电源:2.5mA 电流 - 输出 / 通道:48mA 电压 - 电源，单路/双路(±):2.7 V ~ 5.5 V，±1.35 V ~ 2.75 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:Digi-Reel® 其它名称:MAX4475AUT#TG16DKR |
| AD711SCHIPS | 制造商:AD 制造商全称:Analog Devices 功能描述:Precision, Low Cost, High Speed, BiFET Op Amp |
| AD711SH | 制造商:AD 制造商全称:Analog Devices 功能描述:Precision, Low Cost, High Speed, BiFET Op Amp |
发布紧急采购，3分钟左右您将得到回复。