- 您现在的位置：买卖IC网 > PDF目录9489 > AD7147WPACPZ-RL (Analog Devices Inc)IC CAP-TO-DGTL CONV PROG 24LFCSP PDF资料下载
参数资料
| 型号： | AD7147WPACPZ-RL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 31/73页 |
| 文件大小： | 0K |
| 描述： | IC CAP-TO-DGTL CONV PROG 24LFCSP |
| 标准包装： | 5,000 |
| 系列： | CapTouch™ |
| 类型： | 电容数字转换器 |
| 分辨率（位）： | 16 b |
| 采样率（每秒）： | 250k |
| 数据接口： | 串行，SPI? |
| 电压电源： | 单电源 |
| 电源电压： | 2.6 V ~ 3.6 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-VFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 24-LFCSP-VQ（4x4） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页当前第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页
AD7147
Data Sheet
Rev. D | Page 36 of 72
SDI
CW
15
CW
14
CW
13
CW
8
CW
1
CW
0
XX
SCLK
CW
12
XX
X
READBACK DATA FOR
STARTING REGISTER ADDRESS
X
1
32
23
4
15
16
17
18
31
34
33
48
47
49
CW
11
CW
10
CW
9
CW
7
CW
2
CW
6
CW
5
CW
4
CW
3
11
12
13
14
56
7
8
910
XXX XXX XXX
XXX D15 D14
D1
D0
D1
D0
D15
D14
XXX XXX XXX XXX XXX XXX XXX XXX XXX XXX XXX XXX
SDO
ENABLE WORD
R/W
REGISTER ADDRESS
NOTES
1. MULTIPLE REGISTERS CAN BE READ BACK CONTINUOUSLY.
2. THE 16-BIT CONTROL WORD MUST BE WRITTEN ON SDI: 5 BITS FOR ENABLE WORD, 1 BIT FOR R/W, AND 10 BITS FOR REGISTER ADDRESS.
3. THE ADDRESS AUTOMATICALLY INCREMENTS WITH EACH 16-BIT DATA-WORD BEING READ BACK ON THE SDO PIN.
4. CS IS HELD LOW UNTIL ALL REGISTER BITS HAVE BEEN READ BACK.
5. X DENOTES DON’T CARE.
6. XXX DENOTES HIGH IMPEDANCE THREE-STATE OUTPUT.
7. 16-BIT COMMAND WORD SETTINGS FOR SEQUENTIAL READBACK OPERATION:
CW [15:11] = 11100 (ENABLE WORD)
CW [10] = 1 (R/W)
CW [9:0] = [AD9, AD8, AD7, AD6, AD5, AD4, AD3, AD2, AD1, AD0] (STARTING MSB-JUSTIFIED REGISTER ADDRESS)
READBACK DATA FOR
NEXT REGISTER ADDRESS
CS
16-BIT COMMAND WORD
0
6663-
049
Figure 52. Sequential Register Readback SPI Timing
I2C-COMPATIBLE INTERFACE
The AD7147-1 supports the industry standard 2-wire I2C serial
interface protocol. The two wires associated with the I2C timing
are the SCLK and SDA inputs. The SDA is an I/O pin that allows
both register write and register readback operations. The AD7147-1
is always a slave device on the I2C serial interface bus.
It has a 7-bit device address, Address 0101 1XX. The lower two
bits are set by tying the ADD0 and ADD1 pins high or low. The
AD7147-1 responds when the master device sends its device
address over the bus. The AD7147-1 cannot initiate data trans-
fers on the bus.
Table 18. AD7147-1 I2C Device Address
ADD1
ADD0
I2C Address
0
0101 100
0
1
0101 101
1
0
0101 110
1
0101 111
Data Transfer
Data is transferred over the I2C serial interface in 8-bit bytes.
The master initiates a data transfer by establishing a start con-
dition, defined as a high-to-low transition on the serial data
line, SDA, while the serial clock line, SCLK, remains high. This
indicates that an address/data stream follows.
All slave peripherals connected to the serial bus respond to the
start condition and shift in the next eight bits, consisting of a
7-bit address (MSB first) plus an R/W bit that determines the
direction of the data transfer. The peripheral whose address
corresponds to the transmitted address responds by pulling the
data line low during the ninth clock pulse. This is known as the
acknowledge bit. All other devices on the bus then remain idle
while the selected device waits for data to be read from or written
to it. If the R/W bit is 0, the master writes to the slave device. If
the R/W bit is 1, the master reads from the slave device.
Data is sent over the serial bus in a sequence of nine clock
pulses—eight bits of data followed by an acknowledge bit from
the slave device. Transitions on the data line must occur during
the low period of the clock signal and remain stable during the
high period, because a low-to-high transition when the clock is
high can be interpreted as a stop signal. The number of data
bytes transmitted over the serial bus in a single read or write
operation is limited only by what the master and slave devices
can handle.
When all data bytes are read or written, a stop condition is
established. A stop condition is defined by a low-to-high
transition on SDA while SCLK remains high. If the AD7147
encounters a stop condition, it returns to its idle condition, and
the address pointer register resets to Address 0x00.
相关PDF资料 |
PDF描述 |
|---|---|
| D38999/24FE8HN | CONN RCPT 8POS JAM NUT W/PINS |
| AD7142ACPZ-REEL | IC CAP-TO-DGTL CONV PROG 32LFCSP |
| V375B15M300B2 | CONVERTER MOD DC/DC 15V 300W |
| MS27473T18F35SD | CONN PLUG 66POS STRAIGHT W/SCKT |
| V375B15M300B | CONVERTER MOD DC/DC 15V 300W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7148 | 制造商:AD 制造商全称:Analog Devices 功能描述:Programmable Touch Controller for Single Electrode Capacitance Sensors |
| AD7148ACPZ-1500RL7 | 功能描述:IC CAP-TO-DGTL CONV PROG 16LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 触摸屏控制器 系列:- 标准包装:96 系列:- 类型:- 触摸面板接口:- 输入数/键:- 分辨率（位）:- 评估套件:* 数据接口:- 数据速率/采样率 (SPS，BPS):- 电压基准:- 电源电压:- 电流 - 电源:- 工作温度:- 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:带卷 (TR) |
| AD7148ACPZ-1REEL | 功能描述:IC CAP-TO-DGTL CONV PROG 16LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 触摸屏控制器 系列:- 标准包装:96 系列:- 类型:- 触摸面板接口:- 输入数/键:- 分辨率（位）:- 评估套件:* 数据接口:- 数据速率/采样率 (SPS，BPS):- 电压基准:- 电源电压:- 电流 - 电源:- 工作温度:- 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:带卷 (TR) |
| AD7150 | 制造商:AD 制造商全称:Analog Devices 功能描述:Ultra Low Power, 2 Channel, Capacitance Converter for Proximity Sensing |
| AD7150BRMZ | 功能描述:IC CAP CONV 2CH ULT LP 10MSOP RoHS:是 类别:集成电路 (IC) >> 接口 - 传感器和探测器接口 系列:- 其它有关文件:Automotive Product Guide 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:74 系列:- 类型:触控式传感器 输入类型:数字 输出类型:数字 接口:JTAG，串行 电流 - 电源:100µA 安装类型:表面贴装 封装/外壳:20-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:20-TSSOP 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。