参数资料
型号: AD7193BRUZ
厂商: Analog Devices Inc
文件页数: 36/57页
文件大小: 0K
描述: IC ADC 24BIT SPI 4.8K 28-TSSOP
产品培训模块: Weigh Scale Introduction
标准包装: 50
位数: 24
采样率(每秒): 4.8k
数据接口: DSP,MICROWIRE?,QSPI?,串行,SPI?
转换器数目: 1
电压电源: 模拟和数字
工作温度: -40°C ~ 105°C
安装类型: 表面贴装
封装/外壳: 28-TSSOP(0.173",4.40mm 宽)
供应商设备封装: 28-TSSOP
包装: 管件
输入数目和类型: 4 个差分,单极;4 个差分,双极;8 个伪差分,单极;8 个伪差分,双极
产品目录页面: 777 (CN2011-ZH PDF)
AD7193
Data Sheet
Rev. D | Page 40 of 56
The offset error is, typically, ±150 V/gain. If the gain is changed,
it is advisable to perform a calibration. A zero-scale calibration
(an internal zero-scale calibration or a system zero-scale calibration)
reduces the offset error to the order of the noise.
The gain error of the AD7193 is factory calibrated at a gain of 1
with a 5 V power supply at ambient temperature. Following this
calibration, the gain error is, typically, ±0.001% at 5 V. Table 27
shows the typical uncalibrated gain error for the different gain
settings.
Table 27. Typical Precalibration Gain Error vs. Gain
Gain
Precalibration Gain Error (%)
8
0.11
16
0.20
32
0.23
64
0.29
128
0.39
An internal full-scale calibration reduces the gain error to
±0.001%, typically, when the gain is equal to 1. For higher gains,
the gain error postinternal full-scale calibration is ±0.003%,
typically, when AVDD is equal to or higher than 4.75 V. When
AVDD is less than 4.75 V, the gain error after internal full-scale
calibration is ±0.005%, typically.
When AVDD is less than 4.75 V, the CLK_DIV bit must be set
when performing internal full-scale calibrations. This increases
the calibration time by a factor of 2. The accuracy of the internal
full-scale calibration is further increased if chop is enabled and
a low output data rate is used while performing the calibration.
A system full-scale calibration reduces the gain error to the
order of the noise irrespective of the analog power supply
voltage.
The AD7193 gives the user access to the on-chip calibration
registers, allowing the microprocessor to read the calibration
coefficients of the device and also to write its own calibration
coefficients from prestored values in the EEPROM. A read of
the registers can be performed at any time. However, the ADC
must be placed in power-down or idle mode when writing to
the registers. The values in the calibration registers are 24 bits
wide. The span and offset of the part can also be manipulated
using the registers.
相关PDF资料
PDF描述
LM293AN IC COMPARATOR DUAL DIFF 8-DIP
KA393DTF IC COMPARATOR DUAL DIFF 8-SOP
AMIS42700WCGA4H IC TXRX CAN DUAL HS 20SOIC
AD7718BRUZ IC ADC 24BIT R-R 8/10CH 28-TSSOP
AD7718BRZ IC ADC 24BIT R-R 8/10CH 28SOIC
相关代理商/技术参数
参数描述
AD7193BRUZ 制造商:Analog Devices 功能描述:IC ADC 24BIT 4.8KHZ TSSOP-28
AD7193BRUZ-REEL 功能描述:IC ADC 24BIT SPI 4.8KHZ 28TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率(每秒):45k 数据接口:串行 转换器数目:2 功率耗散(最大):315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC(0.295",7.50mm 宽) 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端,单极
AD7194 制造商:AD 制造商全称:Analog Devices 功能描述:8-Channel, 4.8 kHz, Ultralow Noise, 24-Bit Sigma-Delta ADC with PGA
AD7194BCPZ 功能描述:IC ADC 24BIT SPI 4.8K 32-LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:12 采样率(每秒):300k 数据接口:并联 转换器数目:1 功率耗散(最大):75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC(0.295",7.50mm 宽) 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端,单极;1 个单端,双极
AD7194BCPZ-REEL 功能描述:IC ADC 24BIT SPI 4.8KHZ 32LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率(每秒):45k 数据接口:串行 转换器数目:2 功率耗散(最大):315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC(0.295",7.50mm 宽) 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端,单极