- 您现在的位置：买卖IC网 > PDF目录10973 > AD723ARUZ (Analog Devices Inc)IC ENCODER RGB-NTSC/PAL 28-TSSOP PDF资料下载
参数资料
| 型号： | AD723ARUZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 10/20页 |
| 文件大小： | 0K |
| 描述： | IC ENCODER RGB-NTSC/PAL 28-TSSOP |
| 标准包装： | 50 |
| 类型： | 视频编码器 |
| 应用： | 照相机，互联网设备，机顶盒 |
| 电压 - 电源，数字： | 2.7 V ~ 5.5 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 28-TSSOP |
| 包装： | 管件 |
| 产品目录页面： | 788 (CN2011-ZH PDF) |
REV. 0
AD723
–18–
Implementing a Luma Trap
The AD723 implementation of a luma trap uses an on-chip
resistor along with an off-chip inductor and capacitor to create
an RLC notch filter. The filter must be tuned to the center
frequency of the video standard being output by the AD723,
3.58 MHz for NTSC or 4.43 MHz for PAL.
The circuit is shown in Figure 11. The 1.4 k
series resistor in
the composite video luma path on the AD723 works against the
impedance of the off-chip series LC to form a notch filter. The
frequency of the filter is given by:
f C
=
1
2
π LC
1.4k
14.318180MHz
YTRAP
LUMA
CV
CSET
C
4FSC
A
B
A/
B
17.734475MHz
STND
L
68 H
C1
18pF
47k
D1
1N4148
NTSC/
PAL
AD723
C2
9pF
375
300
375
300
375
300
CVSET
Y
YSET
CHROMA
Figure 11. Luma Trap Circuit for NTSC and PAL Video
Dual-Standard Luma Trap
For a filter that will work for both PAL and NTSC, a means is
required to switch the tuning of the filter between the two
subcarrier frequencies. The PAL standard requires a higher
frequency than NTSC. A basic filter can be made that is tuned
to the PAL subcarrier and a simple diode circuit can then be
used to switch in an extra parallel capacitor that will lower the
filter’s frequency for NTSC operation.
Figure 11 shows how the logic signal that drives STND (Pin 1)
can also be used to drive the circuit that selects the tuning of
the luma trap circuit. When the signal applied to STND is
low (ground), the PAL mode is selected. This results in a bias
of 0 V across D1, which is an Off condition. As a result, C2 is
out of the filter circuit and only C1 tunes the notch filter to the
PAL subcarrier frequency, 4.43 MHz.
On the other hand, when STND is high (3 V), NTSC is selected
and there is a forward bias across D1. This turns the diode on
and adds C2 in parallel with C1. The notch filter is now tuned
to the NTSC subcarrier frequency, 3.58 MHz.
Measuring the Luma Trap Frequency Response
The frequency response of the luma trap can be measured in
two different ways. The first involves using an RGB frequency
sweep input pattern into the AD723 and observing the compos-
ite output on a TV monitor, a TV waveform monitor or on an
oscilloscope.
On a TV monitor, the composite video display will look like
vertical black and white lines that are coarsely spaced (low fre-
quency) on the left side and progress to tightly spaced (high
frequency) on the right side. Somewhere to the right of center,
there will not be discernible stripes, but rather only a gray verti-
cal area. This is the effect of the luma trap, which filters out
luminance detail at a band of frequencies.
At the bottom of the display are markings at each megahertz
that establish a scale of frequency vs. horizontal position. The
location of the center of the gray area along the frequency
marker scale indicates the range of frequencies that are being
filtered out. The gray area should be about halfway between the
3 MHz and 4 MHz markers for NTSC, and about halfway
between the 4 MHz and 5 MHz markers for PAL.
When a horizontal line is viewed on an oscilloscope or video
waveform monitor, the notch in the response will be apparent.
The frequency will have to be interpolated from the location of
the notch position along the H-line.
060
10
20
30
40
50
100
50
0
–50
1.0
0.5
–0.5
0.0
s
VOLTS
IRE
Figure 12. Luminance Sweep with Trap, CV Pin
6
3
–24
0.1
10.0
1.0
0
–3
–6
–9
–12
–15
–18
–21
FREQUENCY – MHz
GAIN
–
dB
Y (LUMA)
C (COMP)
Figure 13. Luminance Frequency Response with NTSC Trap
相关PDF资料 |
PDF描述 |
|---|---|
| VE-B5L-IX-B1 | CONVERTER MOD DC/DC 28V 75W |
| MK20DX128VLF5 | IC ARM CORTEX MCU 128KB 48LQFP |
| VE-B5K-IX-B1 | CONVERTER MOD DC/DC 40V 75W |
| MCF51JE256VLL | IC MCU 32BIT 256K FLASH 100LQFP |
| VE-B5K-IW-B1 | CONVERTER MOD DC/DC 40V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD723ARUZ-REEL | 功能描述:IC ENCODER RGB-NTSC/PAL 28-TSSOP RoHS:是 类别:集成电路 (IC) >> 接口 - 编码器，解码器，转换器 系列:- 产品变化通告:Development Systems Discontinuation 26/Apr/2011 标准包装:1 系列:- 类型:编码器 应用:DVB-S.2 系统 电压 - 电源，模拟:- 电压 - 电源，数字:- 安装类型:- 封装/外壳:模块 供应商设备封装:模块 包装:散装 其它名称:Q4645799 |
| AD723ARUZ-REEL7 | 功能描述:IC ENCODER RGB-NTSC/PAL 28-TSSOP RoHS:是 类别:集成电路 (IC) >> 接口 - 编码器，解码器，转换器 系列:- 产品变化通告:Development Systems Discontinuation 26/Apr/2011 标准包装:1 系列:- 类型:编码器 应用:DVB-S.2 系统 电压 - 电源，模拟:- 电压 - 电源，数字:- 安装类型:- 封装/外壳:模块 供应商设备封装:模块 包装:散装 其它名称:Q4645799 |
| AD723-EVAL | 制造商:Analog Devices 功能描述:AD723 EVALUATION BOARD - Bulk |
| AD723WARUZ-RL7 | 功能描述:RGB to NTSC/PAL Encoder IC Video 28-TSSOP 制造商:analog devices inc. 系列:- 包装:剪切带（CT） 零件状态:有效 类型:RGB 转 NTSC/PAL 编码器 应用:视频 电压 - 电源，模拟:2.7 V ~ 5.5 V 电压 - 电源，数字:2.7 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:28-TSSOP（0.173"，4.40mm 宽） 供应商器件封装:28-TSSOP 标准包装:1 |
| AD724 | 制造商:AD 制造商全称:Analog Devices 功能描述:RGB to NTSC/PAL Encoder |
发布紧急采购，3分钟左右您将得到回复。