- 您现在的位置：买卖IC网 > PDF目录1980 > AD7324BRUZ-REEL (Analog Devices Inc)IC ADC 12BIT+SAR 4CHAN 16-TSSOP PDF资料下载
参数资料
| 型号： | AD7324BRUZ-REEL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 11/37页 |
| 文件大小： | 0K |
| 描述： | IC ADC 12BIT+SAR 4CHAN 16-TSSOP |
| 标准包装： | 2,500 |
| 位数： | 12 |
| 采样率（每秒）： | 1M |
| 数据接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 30mW |
| 电压电源： | 双 ± |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 16-TSSOP |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 4 个单端，单极；4 个单端，双极；2 个差分，单极；2 个差分，双极 |
| 配用： | EVAL-AD7324CBZ-ND - BOARD EVALUATION FOR AD7324CBZ |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页
AD7324
Data Sheet
Rev. B | Page 18 of 36
D
VDD
C2
R1
VIN+
VSS
C1
D
VDD
C2
R1
VIN–
VSS
C1
04864-
024
Figure 30. Equivalent Analog Input Circuit (Differential)
Care should be taken to ensure that the analog input does not
exceed the VDD and VSS supply rails by more than 300 mV.
Exceeding this value causes the diodes to become forward
biased and to start conducting into either the VDD supply rail or
VSS supply rail. These diodes can conduct up to 10 mA without
causing irreversible damage to the part.
In Figure 29 and Figure 30, Capacitor C1 is typically 4 pF and
can primarily be attributed to pin capacitance. Resistor R1 is a
lumped component made up of the on resistance of the input
multiplexer and the track-and-hold switch. Capacitor C2 is the
sampling capacitor; its capacitance varies depending on the
analog input range selected (see the Specifications section).
Track-and-Hold Section
The track-and-hold on the analog input of the AD7324 allows
the ADC to accurately convert an input sine wave of full-scale
amplitude to 13-bit accuracy. The input bandwidth of the track-
and-hold is greater than the Nyquist rate of the ADC. The
AD7324 can handle frequencies up to 22 MHz.
The track-and-hold enters its tracking mode on the 14th SCLK
rising edge after the CS falling edge. The time required to
acquire an input signal depends on how quickly the sampling
capacitor is charged. With 0 source impedance, 305 ns are
sufficient to acquire the signal to the 13-bit level. The
acquisition time required is calculated using the following
formula:
tACQ = 10 × ((RSOURCE + R) × C)
where C is the sampling capacitance and R is the resistance seen
by the track-and-hold amplifier looking back on the input. For
the AD7324, the value of R includes the on resistance of the
input multiplexer and is typically 300 . RSOURCE should include
any extra source impedance on the analog input.
When running the AD7324 at a throughput rate of 1 MSPS with
a 20 MHz SCLK signal, the ADC has approximately
1.5 SCLK + t8 + tQUIET
to acquire the analog input signal. The ADC goes back into
hold mode on the CS falling edge.
As the VDD/VSS supply voltage is reduced, the on resistance of
the input multiplexer increases. Therefore, based on the equation
for tACQ, it is necessary to increase the amount of acquisition
time provided to the AD7324 and, therefore, decrease the overall
throughput rate. Figure 31 shows that if the throughput rate is
reduced when operating with minimum VDD and VSS supplies,
the specified THD performance is maintained.
–50
–95
5
19
±VDD/VSS SUPPLIES (V)
T
HD
(
d
B)
–55
–60
–65
–70
–75
–80
–85
–90
7
9
11
13
15
17
500kSPS
750kSPS
1MSPS
VCC = VDRIVE = 5V
INTERNAL REFERENCE
TA = 25°C
FIN = 10kHz
±5V RANGE
SE MODE
04864-
051
Figure 31. THD vs. ±VDD/VSS Supply Voltage at 500 kSPS, 750 kSPS,
and 1 MSPS
Unlike other bipolar ADCs, the AD7324 does not have a
resistive analog input structure. On the AD7324, the bipolar
analog signal is sampled directly onto the sampling capacitor.
This gives the AD7324 high analog input impedance. An
approximation for the analog input impedance can be
calculated from the following formula:
Z = 1/(fS × CS)
where fS is the sampling frequency, and CS is the sampling
capacitor value.
CS depends on the analog input range chosen (see the
Specifications section). When operating at 1 MSPS, the analog
input impedance is typically 75 kΩ for the ±10 V range. As the
sampling frequency is reduced, the analog input impedance
further increases. As the analog input impedance increases the
current required to drive the analog input, therefore, decreases.
相关PDF资料 |
PDF描述 |
|---|---|
| AD7327BRUZ-REEL7 | IC ADC 12BIT+ SAR 8CHAN 20TSSOP |
| AD7328BRUZ-REEL | IC ADC 12BIT+SAR 8CHAN 20-TSSOP |
| AD7329BRUZ-REEL7 | IC ADC 12BIT+SAR 8CHAN 24-TSSOP |
| AD73311ARSZ | IC ANALOG FRONT END 20-SSOP |
| AD73322LARUZ-REEL | IC PROCESSOR FRONTEND DL 28TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7324BRUZ-REEL7 | 功能描述:IC ADC 12BIT+ SAR 4CHAN 16TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| AD7327 | 制造商:AD 制造商全称:Analog Devices 功能描述:500 kSPS, 8-Channel, Software-Selectable, True Bipolar Input, 12-Bit Plus Sign ADC |
| AD7327BRUZ | 功能描述:IC ADC 12BIT+ SAR 8CHAN 20TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:microPOWER™ 位数:8 采样率（每秒）:1M 数据接口:串行，SPI? 转换器数目:1 功率耗散（最大）:- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘（4x4） 包装:Digi-Reel® 输入数目和类型:8 个单端，单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6 |
| AD7327BRUZ-REEL | 功能描述:IC ADC 12BIT+SAR 8CHAN 20-TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| AD7327BRUZ-REEL7 | 功能描述:IC ADC 12BIT+ SAR 8CHAN 20TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
发布紧急采购，3分钟左右您将得到回复。