- 您现在的位置：买卖IC网 > PDF目录10674 > AD7366BRUZ (Analog Devices Inc)IC ADC 12BIT SAR 1MSPS 24TSSOP PDF资料下载
参数资料
| 型号： | AD7366BRUZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 7/29页 |
| 文件大小： | 0K |
| 描述： | IC ADC 12BIT SAR 1MSPS 24TSSOP |
| 设计资源： | Driving the AD7366/7 Bipolar SAR ADC in Low-Distortion DC-Coupled Appls (CN0042) |
| 标准包装： | 62 |
| 系列： | iCMOS® |
| 位数： | 12 |
| 采样率（每秒）： | 1M |
| 数据接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 转换器数目： | 2 |
| 功率耗散（最大）： | 88.8mW |
| 电压电源： | 模拟和数字，双 ± |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 24-TSSOP |
| 包装： | 管件 |
| 输入数目和类型： | 4 个单端，单极；4 个单端，双极 |
| 产品目录页面： | 777 (CN2011-ZH PDF) |
| 配用： | EVAL-AD7366CBZ-ND - BOARD EVALUATION FOR AD7366 |
第1页第2页第3页第4页第5页第6页当前第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页
AD7366/AD7367
Rev. D | Page 14 of 28
TERMINOLOGY
Differential Nonlinearity (DNL)
DNL is the difference between the measured and the ideal
1 LSB change between any two adjacent codes in the ADC.
Integral Nonlinearity (INL)
INL is the maximum deviation from a straight line passing
through the endpoints of the ADC transfer function. The
endpoints of the transfer function are zero scale, a point 1 LSB
below the first code transition, and full scale, a point 1 LSB above
the last code transition.
Zero Code Error
The deviation of the midscale transition (all 1s to all 0s) from
the ideal VIN voltage, that is, AGND LSB for bipolar ranges
and 2 × VREF 1 LSB for the unipolar range.
Positive Full-Scale Error
The deviation of the last code transition (011…110) to (011…111)
from the ideal (that is, +4 × VREF 1 LSB or +2 × VREF – 1 LSB)
after the zero code error has been factored out.
Negative Full-Scale Error
The deviation of the first code transition (10…000) to (10…001)
from the ideal (that is, 4 × VREF + 1 LSB, 2 × VREF + 1 LSB, or
AGND + 1 LSB) after the zero code error has been factored out.
Zero Code Error Match
The difference in zero code error across all channels.
Positive Full-Scale Error Match
The difference in positive full-scale error across all channels.
Negative Full-Scale Error Match
The difference in negative full-scale error across all channels.
Track-and-Hold Acquisition Time
The track-and-hold amplifier returns to track mode at the end
of a conversion. Track-and-hold acquisition time is the time
required for the output of the track-and-hold amplifier to reach
its final value, within ± LSB, after the end of a conversion.
Signal-to-Noise (+ Distortion) Ratio (SINAD)
This ratio is the measured ratio of signal-to-noise (+ distortion)
at the output of the ADC. The signal is the rms amplitude of the
fundamental. Noise is the sum of all nonfundamental signals up
to half the sampling frequency (fS/2), excluding dc. The ratio is
dependent on the number of quantization levels in the digitiza-
tion process: the more levels, the smaller the quantization noise.
The theoretical signal-to-noise (+ distortion) ratio for an ideal
N-bit converter with a sine wave input is as follows:
Signal-to-Noise (+ Distortion) = (6.02N + 1.76) dB
Thus, for a 12-bit converter, the SINAD is 74 dB.
Total Harmonic Distortion (THD)
THD is the ratio of the rms sum of harmonics to the fundamental.
For the AD7366/AD7367, THD is defined as follows:
1
6
5
4
3
2
V
THD
2
log
20
)
dB
(
+
=
where:
V1 is the rms amplitude of the fundamental.
V2, V3, V4, V5, and V6 are the rms amplitudes of the second
through the sixth harmonics.
Peak Harmonic or Spurious Noise
Peak harmonic, or spurious noise, is the ratio of the rms value
of the next largest component in the ADC output spectrum
(up to fS/2, excluding dc) to the rms value of the fundamental.
Normally, the value of this specification is determined by the
largest harmonic in the spectrum. However, for ADCs where
the harmonics are buried in the noise floor, it is a noise peak.
Channel-to-Channel Isolation
Channel-to-channel isolation is a measure of the level of cross-
talk between any two channels when operating in any of the
input ranges. It is measured by applying a full-scale, 150 kHz
sine wave signal to all unselected input channels and determining
how much that signal is attenuated in the selected channel with
a 50 kHz signal. The figure given is the typical value across all
four channels for the AD7366/AD7367 (see Figure 9 for more
information).
Intermodulation Distortion (IMD)
With inputs consisting of sine waves at two frequencies, fa and
fb, any active device with nonlinearities creates distortion prod-
ucts at the sum, and different frequencies of mfa ± nfb, where
m, n = 0, 1, 2, 3, and so on. Intermodulation distortion terms
are those for which neither m nor n is equal to zero. For example,
the second-order terms include (fa + fb) and (fa fb), and the
third-order terms include (2fa + fb), (2fa fb), (fa + 2fb), and
(fa 2fb).
The AD7366/AD7367 are tested using the CCIF standard where
two input frequencies near the top end of the input bandwidth
are used. In this case, the second-order terms are usually distanced
in frequency from the original sine waves, and the third-order
terms are usually at a frequency close to the input frequencies.
As a result, the second- and third-order terms are specified
separately. The calculation of the intermodulation distortion is
as per the THD specification, where it is the ratio of the rms
sum of the individual distortion products to the rms amplitude
of the sum of the fundamentals expressed in decibels.
相关PDF资料 |
PDF描述 |
|---|---|
| AD7866ARUZ | IC ADC 12BIT 2CH DUAL 20-TSSOP |
| AD7190BRUZ | IC ADC 2CH 24BIT W/PGA 24TSSOP |
| AD7715ARZ-5 | IC ADC 16BIT SIGMA-DELTA 16-SOIC |
| AD7766BRUZ-2 | IC ADC 24BIT 32KSPS SAR 16TSSOP |
| LM2901VDG | IC COMP QUAD SGL SUPPLY 14SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7366BRUZ-5 | 功能描述:IC ADC 12BIT DUAL 500KSPS 24-TSS RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:iCMOS® 其它有关文件:TSA1204 View All Specifications 标准包装:1 系列:- 位数:12 采样率（每秒）:20M 数据接口:并联 转换器数目:2 功率耗散（最大）:155mW 电压电源:模拟和数字 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-TQFP 供应商设备封装:48-TQFP（7x7） 包装:Digi-Reel® 输入数目和类型:4 个单端，单极；2 个差分，单极 产品目录页面:1156 (CN2011-ZH PDF) 其它名称:497-5435-6 |
| AD7366BRUZ-500RL7 | 功能描述:IC ADC 12BIT SAR 1MSPS 24TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:iCMOS® 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| AD7366BRUZ-5500RL7 | 功能描述:IC ADC 12BIT DUAL BIPO 24-TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:iCMOS® 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| AD7366BRUZ-5-RL7 | 功能描述:IC ADC 12BIT DUAL BIPO 24-TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:iCMOS® 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| AD7366BRUZ-REEL7 | 制造商:AD 制造商全称:Analog Devices 功能描述:True Bipolar Input, Dual 1us, 12-Bit, 2-Channel SAR ADC |
发布紧急采购，3分钟左右您将得到回复。