参数资料
型号: AD7367BRUZ-RL7
厂商: Analog Devices Inc
文件页数: 11/29页
文件大小: 0K
描述: IC ADC 14BIT SAR 1MSPS 24TSSOP
设计资源: Driving the AD7366/7 Bipolar SAR ADC in Low-Distortion DC-Coupled Appls (CN0042)
标准包装: 1,000
位数: 14
采样率(每秒): 1M
数据接口: DSP,MICROWIRE?,QSPI?,串行,SPI?
转换器数目: 2
功率耗散(最大): 88.8mW
电压电源: 模拟和数字,双 ±
工作温度: -40°C ~ 85°C
安装类型: 表面贴装
封装/外壳: 24-TSSOP(0.173",4.40mm 宽)
供应商设备封装: 24-TSSOP
包装: 带卷 (TR)
输入数目和类型: 4 个单端,单极;4 个单端,双极
AD7366/AD7367
Rev. D | Page 18 of 28
Unlike other bipolar ADCs, the AD7366/AD7367 do not have a
resistive analog input structure. On the AD7366/AD7367, the
bipolar analog signal is sampled directly onto the sampling
capacitor. This gives the AD7366/AD7367 high analog input
impedance. The analog input impedance can be calculated from
the following formula:
Z = 1/(fS × CS)
where:
fS is the sampling frequency.
CS is the sampling capacitor value.
CS depends on the analog input range chosen (see the Analog
Inputs section). When operating at 1 MSPS, the analog input
impedance is typically 260 kΩ for the ±10 V range. As the
sampling frequency is reduced, the analog input impedance
further increases. As the analog input impedance increases, the
current required to drive the analog input therefore decreases
(see Figure 7 for more information).
TYPICAL CONNECTION DIAGRAM
Figure 20 shows a typical connection diagram for the AD7366/
AD7367. In this configuration, the AGND pin is connected
to the analog ground plane of the system, and the DGND pin
is connected to the digital ground plane of the system. The
analog inputs on the AD7366/AD7367 accept bipolar single-
ended signals. The AD7366/AD7367 can operate with either
an internal or an external reference. In Figure 20, the AD7366/
AD7367 are configured to operate with the internal 2.5 V reference.
A 680 nF decoupling capacitor is required when operating with
the internal reference.
The AVCC and DVCC pins are connected to a 5 V supply voltage.
The VDD and VSS are the dual supplies for the high voltage analog
input structures. The voltage on these pins must be equal to or
greater than ±11.5 V (see Table 7 for more information). The
VDRIVE pin is connected to the supply voltage of the microprocessor.
The voltage applied to the VDRIVE input controls the voltage of
the serial interface. VDRIVE can be set to 3 V or 5 V.
AD7366/
AD7367
M
IC
R
OC
ON
TR
OLLE
R
/
MI
C
R
O
PR
O
C
ESSO
R
CS
VDRIVE
10F
0.1F
+
+3V OR +5V SUPPLY
+11.5V TO +16.5V
SUPPLY
–16.5V TO –11.5V
SUPPLY
+5V SUPPLY
DVCC AVCC
BUSY
CNVST
REFSEL
VDRIVE
DCAPA
DCAPB
ADDR
ANALOG INPUTS ±10V,
±5V, AND 0V TO +10V
680nF
SCLK
DOUTA
DOUTB
DGND
AGND
VSS
VB1
VB2
VA1
VDD
VA2
10F
0.1F
+
0.1F
+
10F
+
0.1F
+
SERIAL
INTERFACE
10F
+
0.1F
+
RANGE1
RANGE0
06703-
022
Figure 20. Typical Connection Diagram Using Internal Reference
相关PDF资料
PDF描述
AD7394ARZ IC DAC 12BIT SERIAL 3V 14SOIC
AD7398BR IC DAC 12BIT QUAD SRL 16-SOIC
AD7401AYRWZ-RL IC MODULATOR SIGMA-DELTA 16SOIC
AD7401YRWZ IC MODULATOR SIGMA-DELTA 16SOIC
AD7450ABRT-R2 IC ADC 12BIT W/DIFF INP SOT-23-8
相关代理商/技术参数
参数描述
AD736AK 制造商:Analog Devices 功能描述:
AD736AQ 功能描述:IC TRUE RMS/DC CONV LP 8-CDIP RoHS:否 类别:集成电路 (IC) >> PMIC - RMS 至 DC 转换器 系列:- 标准包装:46 系列:- 电流 - 电源:1.2mA 电源电压:±18 V,36 V 安装类型:表面贴装 封装/外壳:16-SOIC(0.295",7.50mm 宽) 供应商设备封装:16-SOIC W 包装:管件
AD736AR 制造商:Analog Devices 功能描述:True RMS to DC Converter 8-Pin SOIC N
AD736AR-REEL 功能描述:IC TRUE RMS/DC CONV LP 8-SOIC TR RoHS:否 类别:集成电路 (IC) >> PMIC - RMS 至 DC 转换器 系列:- 标准包装:46 系列:- 电流 - 电源:1.2mA 电源电压:±18 V,36 V 安装类型:表面贴装 封装/外壳:16-SOIC(0.295",7.50mm 宽) 供应商设备封装:16-SOIC W 包装:管件
AD736AR-REEL7 功能描述:IC TRUE RMS/DC CONV LP 8-SOIC TR RoHS:否 类别:集成电路 (IC) >> PMIC - RMS 至 DC 转换器 系列:- 标准包装:46 系列:- 电流 - 电源:1.2mA 电源电压:±18 V,36 V 安装类型:表面贴装 封装/外壳:16-SOIC(0.295",7.50mm 宽) 供应商设备封装:16-SOIC W 包装:管件