- 您现在的位置：买卖IC网 > PDF目录19716 > LTC4245IG#TRPBF (Linear Technology)IC CNTRLR HOT SWAP 36-SSOP PDF资料下载
参数资料
| 型号： | LTC4245IG#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 10/36页 |
| 文件大小： | 431K |
| 描述： | IC CNTRLR HOT SWAP 36-SSOP |
| 标准包装： | 1,000 |
| 类型： | 热交换控制器 |
| 应用： | CompactPCI? |
| 内部开关： | 无 |
| 电源电压： | 3.3V，5V，12V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 36-SSOP（0.209"，5.30mm 宽） |
| 供应商设备封装： | 36-SSOP |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
LTC4245
10
4245fa
PI FU CTIO S
U
U
5V
OUT
: 5V Gate Drive Return; Foldback, ADC and Power
Bad Input. Connect this pin to the source of the 5V supply
external N-channel MOSFET switch for gate drive return.
Power is considered bad if this pin drops below 4.63V or
2.9V depending on the CFG pin. The comparator on this
pin has a built-in hysteresis of 17mV or 11mV. This pin
is also an input to the ADC and the current limit foldback
circuit. A 180?active pull-down discharges 5V
OUT
to
ground when the external MOSFET is turned off.
5V
SENSE
: 5V Supply Current Sense and ADC Input. Con-
nect this pin to the output of the 5V current sense resistor.
The current limit circuit controls the 5V
GATE
pin to limit
the sense voltage between the 5V
IN
and 5V
SENSE
pins to
25mV or less during start-up and 75mV thereafter. Dur-
ing start-up a foldback feature reduces the current limit
to 7.5mV as the 5V
OUT
pin approaches ground. A circuit
breaker, enabled after start-up, trips when the sense voltage
exceeds 25mV for 22約. To disable current limit, connect
this pin to 5V
IN
.
ADR0 to ADR3: Serial Bus Address Inputs. ADR0 and
ADR1 are two-state inputs; ADR2 and ADR3 are three-
state inputs. Tying these pins to ground, open or INTV
CC
con gures one of 32 possible addresses. The addressing
scheme is compatible with the CompactPCI geographic
addressing for slot identi cation. See Table 5 in Applica-
tions Information.
ALERT#: Fault Alert Output. Open-drain logic output that can
be pulled to ground, when a fault occurs, to alert the host
controller. A fault alert is enabled by the ALERT register.
This device is compatible with SMBus alert protocol. See
Applications Information. Tie to ground if unused.
BD_SEL#: Board Present Input. Ground this pin to enable
the N-channel MOSFETs to turn on. When this pin is high,
the MOSFETs are off. An internal 10糀 current source
pulls up this pin to INTV
CC
. Transitions on this pin will be
recorded in the FAULT2 register. A high-to-low transition
activates the logic to read the state of the ON pin and clear
faults. See Applications Information.
CFG: Supply Con guration Three-State Input. When this
pin is grounded, all four supply inputs must satisfy their
undervoltage lockout levels to allow the external MOSFETs
to turn on. Floating this pin disables V
EE
undervoltage
lockout and power bad functions, allowing other supplies
to turn-on even when 12V supply is absent. Tying this
pin to INTV
CC
not only disables V
EE
, but also converts
the 5V
IN
undervoltage, power bad and ADC levels to 3.3V
levels. This allows using an extra 3.3V supply instead of
a 5V supply as in a PCI Express application.
EXPOSED PAD (Pin 39, UHF Package): Exposed Pad may
be left open or connected to device ground.
GND: Device Ground.
GPIO1 to GPIO3 (GPIO2, GPIO3 on UHF package only):
General Purpose Input/Output and ADC Input. Open-drain
logic outputs and logic inputs. Any one of the three pins
can be multiplexed to the GPIO channel of the internal
ADC. GPIO1 has a state change fault associated with it.
The GPIO register (Table 13) contains status and control
bits for these pins.
HEALTHY#: Board Power Status Output. This pin is pulled
low by an open-drain output when all supply outputs are
above their power bad thresholds and when all external
N-channel MOSFETs are on. When any supply output
falls below its power bad threshold voltage, this pin will
go high after a 15約 deglitching time.
INTV
CC
: Internal Low Voltage Supply Decoupling Output.
Connect a 0.1糉 capacitor from this pin to ground. When
this pin falls below 3.8V, the internal registers are reset.
LOCAL_PCI_RST#: Reset Output. This pin is pulled low by
an open-drain output whenever HEALTHY# is high or when
the PCI_RST# input is low. Tie to ground if unused.
ON: On Control Input. A rising edge turns on the external
N-channel MOSFETs and a falling edge turns them off.
This pin is also used to con gure the state of the FET On
control bits (and hence the external FETs) in the ON regis-
ter. For example, if the ON pin is tied high, then one or all
(depending on the Sequence control bit) FET On control
bits will go high 100ms after power-up. Likewise if the ON
pin is tied low then the part will remain off after power-up
until the FET On control bits are set high using the I
2
C
bus. If the Sequence control bit is set, taking ON pin high
turns on the supplies in a 12V, 5V, 3.3V, 12V sequence.
A high-to-low transition on this pin will clear faults.
相关PDF资料 |
PDF描述 |
|---|---|
| 190-009-163R001 | CONN DB9 MALE R/A SOLDER SMD |
| ESA43DRMN | CONN EDGECARD 86POS .125 SQ WW |
| ISPLSI 2128E-135LT176 | IC PLD ISP 128I/O 7.5NS 176TQFP |
| EMA43DRMN | CONN EDGECARD 86POS .125 SQ WW |
| MIC39150-2.5BT | IC REG LDO 2.5V 1.5A TO-220 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7606BSTZ | 制造商:Analog Devices 功能描述:IC ADC 16BIT 200KSPS QFP-64 制造商:Analog Devices 功能描述:IC, ADC, 16BIT, 200KSPS, QFP-64 |
| AD7606BSTZ-4 | 功能描述:IC DAS W/ADC 16BIT 4CH 64LQFP RoHS:是 类别:集成电路 (IC) >> 数据采集 - ADCs/DAC - 专用型 系列:- 产品培训模块:Data Converter Basics 标准包装:1 系列:- 类型:电机控制 分辨率（位）:12 b 采样率（每秒）:1M 数据接口:串行，并联 电压电源:单电源 电源电压:2.7 V ~ 3.6 V，4.5 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:100-TQFP 供应商设备封装:100-TQFP（14x14） 包装:剪切带 (CT) 其它名称:296-18373-1 |
| AD7606BSTZ-4 | 制造商:Analog Devices 功能描述:IC, ADC, 16BIT, 200KSPS, QFP-64 |
| AD7606BSTZ-4RL | 功能描述:IC DAS W/ADC 16BIT 64LQFP RoHS:是 类别:集成电路 (IC) >> 数据采集 - ADCs/DAC - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 类型:数据采集系统（DAS） 分辨率（位）:16 b 采样率（每秒）:21.94k 数据接口:MICROWIRE?，QSPI?，串行，SPI? 电压电源:模拟和数字 电源电压:1.8 V ~ 3.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（6x6） 包装:托盘 |
| AD7606BSTZ-6 | 功能描述:IC DAS W/ADC 16BIT 6CH 64LQFP RoHS:是 类别:集成电路 (IC) >> 数据采集 - ADCs/DAC - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 类型:数据采集系统（DAS） 分辨率（位）:16 b 采样率（每秒）:21.94k 数据接口:MICROWIRE?，QSPI?，串行，SPI? 电压电源:模拟和数字 电源电压:1.8 V ~ 3.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（6x6） 包装:托盘 |
发布紧急采购，3分钟左右您将得到回复。