- 您现在的位置：买卖IC网 > PDF目录19716 > LTC4245IG#TRPBF (Linear Technology)IC CNTRLR HOT SWAP 36-SSOP PDF资料下载
参数资料
| 型号： | LTC4245IG#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 17/36页 |
| 文件大小： | 431K |
| 描述： | IC CNTRLR HOT SWAP 36-SSOP |
| 标准包装： | 1,000 |
| 类型： | 热交换控制器 |
| 应用： | CompactPCI? |
| 内部开关： | 无 |
| 电源电压： | 3.3V，5V，12V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 36-SSOP（0.209"，5.30mm 宽） |
| 供应商设备封装： | 36-SSOP |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
LTC4245
17
4245fa
Turn-Off
The switches can be turned off by a variety of condi-
tions.
1. ON pin going low or BD_SEL# going high turns off all
switches.
2. Individual switches can be turned off by resetting
the particular FET On control bit (D0 to D3) through
the serial bus.
3. A variety of fault conditions will turn off all switches
together. These include supply undervoltage,
overcurrent circuit breaker and PGI faults.
4. Writing a logic one into the undervoltage, overcurrent
or PGI fault bits will turn off all switches, if the
corresponding autoretry is not enabled.
Normally the 12V, 5V and 3.3V switches are turned off
with a 1.3mA current pulling down the gate to ground.
V
EEGATE
is pulled through a resistive switch to V
EEIN
. All
supply outputs are also discharged to ground through
internal switches. When any MOSFET is shut off, the
HEALTHY# signal pulls high and LOCAL_PCI_RST# will
be asserted low. Figure 4 shows all supplies being turned
off by BD_SEL# going high.
ON Register and Sequencing
The LTC4245 features an ON register (Table 10) consisting
of four On control bits (D0 to D3) and four On status bits
(D4 to D7). D0 to D3 provide independent on/off control
for each supply through the I
2
C bus. Bits D4 to D7 report
the on status of each supply. Even though a supply may
be commanded to turn-on by setting its On control bit,
it may remain off (On status bit low) because the condi-
tions to turn on, as listed in the Turn-On section, may not
be present.
The sequence control bit, C6, determines whether the four
supply MOSFETs turn-on together or in a xed sequence.
The default state is no sequencing. In this case taking
the ON pin high sets all the four On control bits. If the
start-up conditions are satis ed, all switches will turn on
under the control of a single TIMER and SS cycle. Due to
different input voltage offsets in the current limit ampli er
of each supply, the gate turn-on of all MOSFETs will not
occur at the same moment but will happen in random
order depending on ampli er offset and soft-start ramp
rate. The gate turn-ons will be truly simultaneous only if
SS pin is left open.
If bit C6 is set, then the ON pin going high sets only the
12V On control bit, D0. The 12V back-end supply ramps
up. The end of the TIMER and SS cycle sets the 5V On
control bit, D1, starting the ramp of the 5V supply output.
The end of the 5V timing cycle sets bit D2 and the end of
the 3.3V ramp sets bit D3. In this way, the four On control
APPLICATIO S I FOR ATIO
U
U
U
Figure 4. Normal Turn-Off Waveform
TIME 100ms/DIV
4245 F04
12V
OUT
, 5V
OUT
3V
OUT
, V
EEOUT
, 10V/DIV
BD_SEL#
5V/DIV
HEALTHY#
5V/DIV
LOCAL_PCI_RST#
5V/DIV
Figure 5. Sequential Turn-On Waveform
TIME 50ms/DIV
4245 F05
SS
2.5V/DIV
TIMER
2.5V/DIV
12V
OUT
, 5V
OUT
3V
OUT
, V
EEOUT
, 10V/DIV
BD_SEL#
5V/DIV
HEALTHY#
5V/DIV
LOCAL_PCI_RST#
5V/DIV
bits get set one after another, leading to a 12V, 5V, 3.3V,
12V start-up sequence. Figure 5 illustrates this. If C6 is set
and any of the start-up conditions goes bad, all switches
turn-off, and all On control bits except D0 are reset. This
ensures that the part goes through a sequenced turn-on
during auto-retry. D1 to D3 are also reset when BD_SEL#
goes low with C6 set.
相关PDF资料 |
PDF描述 |
|---|---|
| 190-009-163R001 | CONN DB9 MALE R/A SOLDER SMD |
| ESA43DRMN | CONN EDGECARD 86POS .125 SQ WW |
| ISPLSI 2128E-135LT176 | IC PLD ISP 128I/O 7.5NS 176TQFP |
| EMA43DRMN | CONN EDGECARD 86POS .125 SQ WW |
| MIC39150-2.5BT | IC REG LDO 2.5V 1.5A TO-220 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4245IUHF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Multiple Supply Hot Swap Controller with I2C Compatible Monitoring |
| LTC4245IUHF#PBF | 功能描述:IC CNTRLR HOT SWAP 38-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:119 系列:- 类型:热交换控制器 应用:通用型，PCI Express? 内部开关:无 电流限制:- 电源电压:3.3V，12V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:80-TQFP 供应商设备封装:80-TQFP（12x12） 包装:托盘 产品目录页面:1423 (CN2011-ZH PDF) |
| LTC4245IUHF#TRPBF | 功能描述:IC CNTRLR HOT SWAP 38-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:119 系列:- 类型:热交换控制器 应用:通用型，PCI Express? 内部开关:无 电流限制:- 电源电压:3.3V，12V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:80-TQFP 供应商设备封装:80-TQFP（12x12） 包装:托盘 产品目录页面:1423 (CN2011-ZH PDF) |
| LTC4251 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Negative Voltage Hot Swap Controllers in SOT-23 |
| LTC4251_12 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Negative Voltage Hot Swap Controllers in SOT-23 |
发布紧急采购，3分钟左右您将得到回复。