参数资料
型号: LTC4245IG#TRPBF
厂商: Linear Technology
文件页数: 11/36页
文件大小: 431K
描述: IC CNTRLR HOT SWAP 36-SSOP
标准包装: 1,000
类型: 热交换控制器
应用: CompactPCI?
内部开关:
电源电压: 3.3V,5V,12V
工作温度: -40°C ~ 85°C
安装类型: 表面贴装
封装/外壳: 36-SSOP(0.209",5.30mm 宽)
供应商设备封装: 36-SSOP
包装: 带卷 (TR)
LTC4245
11
4245fa
PI   FU CTIO S
U
U
PCI_RST#: Reset Input. Pulling this pin low causes LO-
CAL_PCI_RST# to pull low. When high, LOCAL_PCI_RST#
is the logical inverse of HEALTHY#. Tie to INTV
CC
  if
unused.
PGI: Power Good Input. Tie this pin to the 
?/DIV>
R
?/DIV>
E
?/DIV>
S
?/DIV>
E
?/DIV>
T output
of an external supply monitor or power good output of a
DC/DC converter. When all supplies have been turned on,
a timing cycle is started at the end of which the PGI pin is
sampled. If it is low, all external MOSFETs are shut off. If
the PGI Disable control bit C3 is not set, pulling this pin
low for more than 20約 during normal operation will also
shut off all MOSFETs. Tie to INTV
CC
 if unused.
PRECHARGE: Bus Precharge Output. This pin can source 
70mA at 1V as soon as 3V
IN
 is powered-up. Leave it open
if unused.
SCL: Serial Bus Clock Input. Data at the SDA pin is shifted 
in or out on rising edges of SCL. This is a high impedance
pin that is generally driven by an open-collector output
from a master controller.
SDA: Serial Bus Data Input and Output. This is a high 
impedance input when address, command or data bits
are shifted in. It is an open-drain output when sending
data back to the master controller or acknowledging a
write operation. An external pull-up resistor or current
source is required.
SS: Soft-Start Input. Connect a capacitor between this pin 
and ground to set the rate of increase of current limit during
start-up for dI/dt limited inrush current. When an external
MOSFET is turned on, a 20糀 pull-up current charges the
capacitor. The voltage ramp on the capacitor is converted
into an internal current limit increasing linearly with time.
Leave it open if dI/dt limited inrush is not required.
TIMER: Timer Input. A capacitor between this pin and 
ground sets the duration of the start-up, PGI and auto-retry
timing cycles to be 23.3ms/糉, 233ms/糉 and 1.17s/糉
respectively. A timing cycle consists of TIMER being
charged to 2.56V with an internal pull-up current source
and then being reset by a switch to ground. The timing
cycle ends when TIMER falls below 0.23V. The start-up,
PGI and auto-retry timing cycles use 100糀, 10糀 and
2糀 pull-up current sources respectively.
V
EEGATE
: Gate Drive for 12V Supply External N-Chan-
nel MOSFET. An internal 20糀 current source charges
the gate of the external N-channel MOSFET. An internal
clamp limits the gate voltage to 6.2V above V
EEIN
. During
turn-off, a 3.5mA pull-down current discharges V
EEGATE
 
to V
EEIN
. During short-circuit a 65mA pull-down current
between V
EEGATE
 and V
EEIN
 is activated. If a 12V supply
is not available, connect V
EEGATE
 to ground and use the
CFG pin appropriately.
V
EEIN
: 12V Supply, Current Sense and ADC Input. An 
undervoltage lockout circuit, with 38mV hysteresis, pre-
vents any external MOSFET from turning on when this
pin is above 10.5V. The V
EEIN
 undervoltage lockout can
be disabled by using the CFG pin. If a 12V supply is not
available, connect V
EEIN
 to ground and use the CFG pin
appropriately.
V
EEOUT
: 12V Supply Foldback, ADC and Power Bad Input. 
Connect this pin to the drain of the 12V supply external
N-channel MOSFET switch. Power is considered bad if this
pin rises above 11.1V. The comparator on this pin has a
built-in hysteresis of 54mV. The V
EEOUT
 power bad function
can be disabled by using the CFG pin. This pin is also an
input to the ADC and the current limit foldback circuit. A
1800?active pull-up discharges V
EEOUT
 to ground when
the external MOSFET is turned off. If a 12V supply is not
available, connect V
EEOUT
 to ground and use the CFG pin
appropriately.
V
EESENSE
: 12V Supply Current Sense and ADC Input. 
Connect this pin to the output of the 12V current sense
resistor. The current limit circuit controls the V
EEGATE
 pin
to limit the sense voltage between the V
EESENSE
 and V
EEIN
 
pins to 50mV or less during start-up and 150mV thereafter.
During start-up a foldback feature lowers the current limit
to 16mV as the V
EEOUT
 pin approaches ground. A circuit
breaker, enabled after start-up, trips when the sense voltage
exceeds 50mV for 22約. To disable current limit, connect
this pin to V
EEIN
. If a 12V supply is not available, connect
V
EESENSE
 to ground and use the CFG pin appropriately.
相关PDF资料
PDF描述
190-009-163R001 CONN DB9 MALE R/A SOLDER SMD
ESA43DRMN CONN EDGECARD 86POS .125 SQ WW
ISPLSI 2128E-135LT176 IC PLD ISP 128I/O 7.5NS 176TQFP
EMA43DRMN CONN EDGECARD 86POS .125 SQ WW
MIC39150-2.5BT IC REG LDO 2.5V 1.5A TO-220
相关代理商/技术参数
参数描述
AD7606BSTZ 制造商:Analog Devices 功能描述:IC ADC 16BIT 200KSPS QFP-64 制造商:Analog Devices 功能描述:IC, ADC, 16BIT, 200KSPS, QFP-64
AD7606BSTZ-4 功能描述:IC DAS W/ADC 16BIT 4CH 64LQFP RoHS:是 类别:集成电路 (IC) >> 数据采集 - ADCs/DAC - 专用型 系列:- 产品培训模块:Data Converter Basics 标准包装:1 系列:- 类型:电机控制 分辨率(位):12 b 采样率(每秒):1M 数据接口:串行,并联 电压电源:单电源 电源电压:2.7 V ~ 3.6 V,4.5 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:100-TQFP 供应商设备封装:100-TQFP(14x14) 包装:剪切带 (CT) 其它名称:296-18373-1
AD7606BSTZ-4 制造商:Analog Devices 功能描述:IC, ADC, 16BIT, 200KSPS, QFP-64
AD7606BSTZ-4RL 功能描述:IC DAS W/ADC 16BIT 64LQFP RoHS:是 类别:集成电路 (IC) >> 数据采集 - ADCs/DAC - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 类型:数据采集系统(DAS) 分辨率(位):16 b 采样率(每秒):21.94k 数据接口:MICROWIRE?,QSPI?,串行,SPI? 电压电源:模拟和数字 电源电压:1.8 V ~ 3.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP(6x6) 包装:托盘
AD7606BSTZ-6 功能描述:IC DAS W/ADC 16BIT 6CH 64LQFP RoHS:是 类别:集成电路 (IC) >> 数据采集 - ADCs/DAC - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 类型:数据采集系统(DAS) 分辨率(位):16 b 采样率(每秒):21.94k 数据接口:MICROWIRE?,QSPI?,串行,SPI? 电压电源:模拟和数字 电源电压:1.8 V ~ 3.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP(6x6) 包装:托盘