参数资料
| 型号： | AD7650ACPZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 9/20页 |
| 文件大小： | 0K |
| 描述： | IC ADC 16BIT CMOS 5V 48LFCSP |
| 标准包装： | 1 |
| 位数： | 16 |
| 采样率（每秒）： | 570k |
| 数据接口： | 串行，并联 |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 77mW |
| 电压电源： | 模拟和数字 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-VFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 48-LFCSP-VQ（7x7） |
| 包装： | 托盘 |
| 输入数目和类型： | 1 个伪差分，单极 |
| 配用： | EVAL-AD7650CBZ-ND - BOARD EVALUATION FOR AD7650 |
REV. 0
–17–
AD7650
MICROPROCESSOR INTERFACING
The AD7650 is ideally suited for traditional dc measurement appli-
cations supporting a microprocessor, and ac signal processing
applications interfacing to a digital signal processor. The AD7650
is designed to interface either with a parallel 16-bit-wide interface or
with a general-purpose serial port or I/O ports on a microcontroller.
A variety of external buffers can be used with the AD7650 to
prevent digital noise from coupling into the ADC. The following
sections illustrate the use of the AD7650 with an SPI-equipped
microcontroller, the ADSP-21065L and ADSP-218x signal
processors.
SPI Interface (MC68HC11)
Figure 18 shows an interface diagram between the AD7650 and an
SPI-equipped microcontroller like the MC68HC11. To accom-
modate the slower speed of the microcontroller, the AD7650 acts
as a slave device and data must be read after conversion. This mode
allows also the “daisy chain” feature.
The convert command could be initiated in response to an internal
timer interrupt. The reading of output data, one byte at a time,
if necessary, could be initiated in response to the end-of-conversion
signal (BUSY going low) using to an interrupt line of the
microcontroller. The Serial Peripheral Interface (SPI) on the
MC68HC11 is configured for master mode (MSTR = 1), Clock
Polarity Bit (CPOL) = 0, Clock Phase Bit (CPHA) = 1 and SPI
Interrupt Enable (SPIE = 1) by writing to the SPI Control Reg-
ister (SPCR). The IRQ is configured for edge-sensitive-only
operation (IRQE = 1 in OPTION register).
IRQ
MC68HC11
*
CNVST
AD7650*
CS
BUSY
MISO/SDI
SCK
I/O PORT
SDOUT
SCLK
RD
INVSCLK
EXT/
INT
SER/
PAR
DVDD
*ADDITIONAL PINS OMITTED FOR CLARITY
OVDD
Figure 18. Interfacing the AD7650 to SPI Interface
ADSP-21065L in Master Serial Interface
As shown in Figure 19, the AD7650 can be interfaced to the
ADSP-21065L using the serial interface in master mode without
any glue logic required. This mode combines the advantages of
reducing the number of wire connections and being able to read
the data during or after conversion at user convenience.
The AD7650 is configured for the internal clock mode (EXT/
INT
low) and acts, therefore, as the master device. The convert com-
mand can be generated by either an external low jitter oscillator
or, as shown, by a FLAG output of the ADSP-21065L or by a
frame output TFS of one serial port of the ADSP-21065L which
can be used as a timer. The serial port on the ADSP-21065L is
configured for external clock (IRFS = 0), rising edge active
(CKRE = 1), external late framed sync signals (IRFS = 0, LAFS = 1,
RFSR = 1) and active high (LRFS = 0). The serial port of the
ADSP-21065L is configured by writing to its receive control
register (SRCTL)—see ADSP-2106x SHARC User’s Manual.
Because the serial port within the ADSP-21065L will be seeing
a discontinuous clock, an initial word reading has to be done
after the ADSP-21065L has been reset to ensure that the serial
port is properly synchronized to this clock during each following
data read operation.
RFS
ADSP-21065L*
SHARC
CNVST
AD7650*
CS
SYNC
RD
DR
RCLK
FLAG OR TFS
SDOUT
SCLK
INVSYNC
INVSCLK
EXT/
INT
RDC/SDIN
SER/
PAR
DVDD
*ADDITIONAL PINS OMITTED FOR CLARITY
OVDD
OR
OGND
Figure 19. Interfacing to the ADSP-21065L Using the
Serial Master Mode
相关PDF资料 |
PDF描述 |
|---|---|
| AD7651ACPZ | IC ADC 16BIT UNIPOLAR 48LFCSP |
| AD7652ASTZ | IC ADC 16BIT 500KSPS REF 48LQFP |
| AD7653ACPZRL | IC ADC 16BIT UNIPOLAR 48LFCSP |
| AD7654ACPZ | IC ADC 16BIT DUAL 2CH 48-LFCSP |
| AD7655ACPZRL | IC ADC 16BIT 4CHAN 48LFCSP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7650ACPZRL | 功能描述:IC ADC 16BIT CMOS 5V 48LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极 |
| AD7650AST | 制造商:Analog Devices 功能描述:ADC Single SAR 570ksps 16-bit Parallel/Serial 48-Pin LQFP 制造商:Rochester Electronics LLC 功能描述:16-BIT, 570KSPS CMOS LOW COST CMOS ADC - Bulk |
| AD7650ASTRL | 制造商:Analog Devices 功能描述:ADC Single SAR 570ksps 16-bit Parallel/Serial 48-Pin LQFP T/R 制造商:Rochester Electronics LLC 功能描述:16-BIT, 570KSPS LOW COST CMOS ADC - Tape and Reel |
| AD7650ASTZ | 功能描述:IC ADC 16BIT 570KSPS 48LQFP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 其它有关文件:TSA1204 View All Specifications 标准包装:1 系列:- 位数:12 采样率（每秒）:20M 数据接口:并联 转换器数目:2 功率耗散（最大）:155mW 电压电源:模拟和数字 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-TQFP 供应商设备封装:48-TQFP（7x7） 包装:Digi-Reel® 输入数目和类型:4 个单端，单极；2 个差分，单极 产品目录页面:1156 (CN2011-ZH PDF) 其它名称:497-5435-6 |
| AD7650ASTZRL | 功能描述:IC ADC 16BIT CMOS 5V 48LQFP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极 |
发布紧急采购，3分钟左右您将得到回复。