- 您现在的位置：买卖IC网 > PDF目录10672 > AD7680BRMZ (Analog Devices Inc)IC ADC 16BIT LP UNIPOLAR 8-MSOP PDF资料下载
参数资料
| 型号： | AD7680BRMZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 24/24页 |
| 文件大小： | 0K |
| 描述： | IC ADC 16BIT LP UNIPOLAR 8-MSOP |
| 标准包装： | 50 |
| 系列： | PulSAR® |
| 位数： | 16 |
| 采样率（每秒）： | 100k |
| 数据接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 26.4mW |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-MSOP |
| 包装： | 管件 |
| 输入数目和类型： | 1 个单端，单极 |
| 产品目录页面： | 778 (CN2011-ZH PDF) |
AD7680
Rev. A | Page 9 of 24
TERMINOLOGY
Integral Nonlinearity
This is the maximum deviation from a straight line passing
through the endpoints of the ADC transfer function. The
endpoints of the transfer function are zero scale, a point
1/2 LSB below the first code transition, and full scale, a point
1/2 LSB above the last code transition.
Differential Nonlinearity
This is the difference between the measured and the ideal 1 LSB
change between any two adjacent codes in the ADC.
Offset Error
This is the deviation of the first code transition (00 . . . 000) to
(00 . . . 001) from the ideal, i.e., AGND + 1 LSB.
Gain Error
This is the deviation of the last code transition (111 . . . 110) to
(111 . . . 111) from the ideal (i.e., VREF 1 LSB) after the offset
error has been adjusted out.
Track-and-Hold Acquisition Time
The track-and-hold amplifier returns to track mode at the end
of conversion. The track-and-hold acquisition time is the time
required for the output of the track-and-hold amplifier to reach
its final value, within ±1 LSB, after the end of the conversion.
See the Serial Interface section for more details.
Signal-to-(Noise + Distortion) Ratio
This is the measured ratio of signal-to-(noise + distortion) at
the output of the ADC. The signal is the rms amplitude of the
fundamental. Noise is the sum of all nonfundamental signals up
to half the sampling frequency (fS/2, excluding dc). The ratio
depends on the number of quantization levels in the digitization
process; the more levels, the smaller the quantization noise. The
theoretical signal-to-(noise + distortion) ratio for an ideal N-bit
converter with a sine wave input is given by
Signal-to-(Noise + Distortion) = (6.02 N + 1.76) dB
Thus, for a 16-bit converter, this is 98 dB.
Total Harmonic Distortion (THD)
THD is the ratio of the rms sum of harmonics to the
fundamental. For the AD7680, it is defined as
1
2
6
2
5
2
4
2
3
2
V
dB
THD
+
=
log
20
)
(
where V1 is the rms amplitude of the fundamental and V2, V3,
V4, V5, and V6 are the rms amplitudes of the second through the
sixth harmonics.
Peak Harmonic or Spurious Noise
Peak harmonic or spurious noise is defined as the ratio of the
rms value of the next largest component in the ADC output
spectrum (up to fS/2, excluding dc) to the rms value of the
fundamental. Normally, the value of this specification is
determined by the largest harmonic in the spectrum, but for
ADCs where the harmonics are buried in the noise floor, it is a
noise peak.
Intermodulation Distortion
With inputs consisting of sine waves at two frequencies, fa and fb,
any active device with nonlinearities creates distortion products
at the sum and difference frequencies of mfa ± nfb where m, n =
0, 1, 2, 3. Intermodulation distortion terms are those for which
neither m nor n are equal to zero. For example, the second-order
terms include (fa + fb) and (fa fb), while the third-order terms
include (2fa + fb), (2fa fb), (fa + 2fb), and (fa 2fb).
The AD7680 is tested using the CCIF standard where two input
frequencies near the top end of the input bandwidth are used.
In this case, the second-order terms are usually distanced in
frequency from the original sine waves, while the third-order
terms are usually at a frequency close to the input frequencies.
As a result, the second- and third-order terms are specified
separately. The calculation of the intermodulation distortion is
as per the THD specification where it is the ratio of the rms
sum of the individual distortion products to the rms amplitude
of the sum of the fundamentals expressed in dBs.
相关PDF资料 |
PDF描述 |
|---|---|
| AD7472ARUZ | IC ADC 12BIT PAR 1.5MSPS 24TSSOP |
| ISL3333IRZ | IC TXRX RS485/422 2PRT 40-QFN |
| LTC1594IS#PBF | IC A/D CONV 12BIT SRL 4CH 16SOIC |
| ISL81334IAZ | IC TXRX DUAL 2PORT ESD 28-SSOP |
| ISL41334IRZ | IC TXRX DUAL PROTOCAL ESD 40-QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7680BRMZ | 制造商:Analog Devices 功能描述:IC 16BIT ADC SMD 7680 MSOP8 |
| AD7680BRMZ-REEL | 功能描述:IC ADC 16BIT LP UNIPOLR 8MSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:PulSAR® 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| AD7680BRMZ-REEL7 | 功能描述:IC ADC 16BIT LP UNIPOLR 8MSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:PulSAR® 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| AD7682 | 制造商:AD 制造商全称:Analog Devices 功能描述:14-Bit, 8-Channel, 250 kSPS PulSAR ADC |
| AD7682BCBZ-RL7 | 功能描述:16 Bit Analog to Digital Converter 4 Input 1 SAR 20-WLCSP (2.39x2.39) 制造商:analog devices inc. 系列:PulSAR? 包装:带卷（TR） 零件状态:有效 位数:16 采样率（每秒）:250k 输入数:4 输入类型:差分，单端 数据接口:SPI，DSP 配置:MUX-S/H-ADC 无线电 - S/H:ADC:1:1 A/D 转换器数:1 架构:SAR 参考类型:外部， 内部 电压 - 电源，模拟:2.3 V ~ 5.5 V 电压 - 电源，数字:* 特性:温度传感器 工作温度:-40°C ~ 85°C 封装/外壳:20-UFBGA，WLCSP 供应商器件封装:20-WLCSP（2.39x2.39） 标准包装:1,500 |
发布紧急采购，3分钟左右您将得到回复。