参数资料
型号: AD7688BCPZRL7
厂商: Analog Devices Inc
文件页数: 10/28页
文件大小: 0K
描述: IC ADC 16BIT SAR 500KSPS 10LFCSP
标准包装: 1
系列: PulSAR®
位数: 16
采样率(每秒): 500k
数据接口: DSP,MICROWIRE?,QSPI?,串行,SPI?
转换器数目: 1
功率耗散(最大): 21.5mW
电压电源: 模拟和数字
工作温度: -40°C ~ 85°C
安装类型: 表面贴装
封装/外壳: 10-WFDFN 裸露焊盘,CSP
供应商设备封装: 10-LFCSP-WD(3x3)
包装: 标准包装
输入数目和类型: 2 个单端,单极;2 个单端,双极;1 个差分,单极;1 个差分,双极
其它名称: AD7688BCPZRL7DKR
AD7688
Rev. A | Page 18 of 28
CS MODE 3-WIRE WITH BUSY INDICATOR
This mode is usually used when a single AD7688 is connected
to an SPI-compatible digital host having an interrupt input.
The connection diagram is shown in Figure 36 and the
corresponding timing is given in Figure 37.
With SDI tied to VIO, a rising edge on CNV initiates a
conversion, selects the CS mode, and forces SDO to high
impedance. SDO is maintained in high impedance until the
completion of the conversion irrespective of the state of CNV.
Prior to the minimum conversion time, CNV could be used to
select other SPI devices, such as analog multiplexers, but CNV
must be returned low before the minimum conversion time and
held low until the maximum conversion time to guarantee the
generation of the BUSY signal indicator. When the conversion
is complete, SDO goes from high impedance to low. With a
pull-up on the SDO line, this transition can be used as an
interrupt signal to initiate the data reading controlled by the
digital host. The AD7688 then enters the acquisition phase and
powers down. The data bits are then clocked out, MSB first, by
subsequent SCK falling edges. The data is valid on both SCK
edges. Although the rising edge can be used to capture the data,
a digital host using the SCK falling edge allows a faster reading
rate provided it has an acceptable hold time. After the optional
17th SCK falling edge, or when CNV goes high, whichever is
earlier, SDO returns to high impedance.
If multiple AD7688s are selected at the same time, the SDO
output pin handles this contention without damage or induced
latch-up. Meanwhile, it is recommended to keep this contention
as short as possible to limit extra power dissipation.
DATA IN
IRQ
CLK
CONVERT
VIO
DIGITAL HOST
02973-
035
47k
Ω
CNV
SCK
SDO
SDI
VIO
AD7688
Figure 36. CS Mode 3-Wire with BUSY Indicator
Connection Diagram (SDI High)
SDO
D15
D14
D1
D0
tDIS
SCK
12
3
15
16
17
tSCK
tSCKL
tSCKH
tHSDO
tDSDO
CNV
CONVERSION
ACQUISITION
tCONV
tCYC
tCNVH
tACQ
ACQUISITION
SDI = 1
02973-
036
Figure 37. CS Mode 3-Wire with BUSY Indicator Serial Interface Timing (SDI High)
相关PDF资料
PDF描述
AD7689BCPZRL7 IC ADC 16BIT 250KSPS 8CH 20LFCSP
AD7690BCPZRL IC ADC 18BIT 400KSPS 10-LFCSP
AD7691BCPZRL7 IC ADC 18BIT SAR 250KSPS 10LFCSP
AD7693BRMZRL7 IC ADC 16BIT 500KSPS 10-MSOP
AD7694ARMZ IC ADC 16BIT SAR 250KSPS 8MSOP
相关代理商/技术参数
参数描述
AD7688BRM 制造商:Analog Devices 功能描述:ADC Single SAR 500ksps 16-bit Serial 10-Pin MSOP Tube 制造商:Rochester Electronics LLC 功能描述:16-BIT DIFF, 550KSPS SERIAL MSOP ADC - Bulk 制造商:Analog Devices 功能描述:IC 16-BIT ADC
AD7688BRMRL7 制造商:Analog Devices 功能描述:ADC Single SAR 500ksps 16-bit Serial 10-Pin MSOP T/R
AD7688BRMZ 功能描述:IC ADC DIFF 16BIT 500KSPS 10MSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:PulSAR® 标准包装:1 系列:microPOWER™ 位数:8 采样率(每秒):1M 数据接口:串行,SPI? 转换器数目:1 功率耗散(最大):- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘(4x4) 包装:Digi-Reel® 输入数目和类型:8 个单端,单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6
AD7688BRMZRL7 功能描述:IC ADC 16BIT 500KSPS 10MSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:PulSAR® 标准包装:1,000 系列:- 位数:12 采样率(每秒):300k 数据接口:并联 转换器数目:1 功率耗散(最大):75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC(0.295",7.50mm 宽) 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端,单极;1 个单端,双极
AD7689 制造商:AD 制造商全称:Analog Devices 功能描述:14-Bit, 8-Channel, 250 kSPS PulSAR ADC