参数资料
型号: AD7690BRMZ
厂商: Analog Devices Inc
文件页数: 7/24页
文件大小: 0K
描述: IC ADC 18BIT 400KSPS 10MSOP
标准包装: 1
系列: PulSAR®
位数: 18
采样率(每秒): 400k
数据接口: DSP,MICROWIRE?,QSPI?,串行,SPI?
转换器数目: 1
功率耗散(最大): 20mW
电压电源: 模拟和数字
工作温度: -40°C ~ 85°C
安装类型: 表面贴装
封装/外壳: 10-TFSOP,10-MSOP(0.118",3.00mm 宽)
供应商设备封装: 10-MSOP
包装: 管件
输入数目和类型: 1 个差分,双极
产品目录页面: 778 (CN2011-ZH PDF)
AD7690
Rev. B | Page 15 of 24
For ac applications, the driver should have a THD
performance commensurate with the AD7690.
For multichannel multiplexed applications, the driver
amplifier and the AD7690 analog input circuit must settle
for a full-scale step onto the capacitor array at an 18-bit
level (0.0004%, 4 ppm). In the amplifier’s data sheet, settling
at 0.1% to 0.01% is more commonly specified. This may
differ significantly from the settling time at an 18-bit level
and should be verified prior to driver selection.
Table 8. Recommended Driver Amplifiers
Amplifier
Typical Application
Very low noise, low power single to differential
Very low noise, small, and low power
5 V single supply, low noise
Very low noise and high frequency
Low noise and high frequency
Low power, low noise, and low frequency
5 V single supply, low power
SINGLE-TO-DIFFERENTIAL DRIVER
For applications using a single-ended analog signal, either bipolar
or unipolar, the ADA4941-1 single-ended-to-differential driver
allows for a differential input into the part. The schematic is
shown in Figure 30.
R1 and R2 set the attenuation ratio between the input range and
the ADC range (VREF). R1, R2, and CF are chosen depending on
the desired input resistance, signal bandwidth, antialiasing, and
noise contribution. For example, for the ±10 V range with a 4 kΩ
impedance, R2 = 1 kΩ and R1 = 4 kΩ.
R3 and R4 set the common mode on the IN input, and R5 and
R6 set the common mode on the IN+ input of the ADC. The
common mode should be set close to VREF/2; however, if single
supply is desired, it can be set slightly above VREF/2 to provide
some headroom for the ADA4941-1 output stage. For example,
for the ±10 V range with a single supply, R3 = 8.45 kΩ, R4 =
11.8 kΩ, R5 = 10.5 kΩ, and R6 = 9.76 kΩ.
AD7690
REF
GND
VDD
IN+
2.7nF
100nF
2.7nF
IN–
+5V REF
±10V, ±5V, ...
+5.2V
15
10F
15
R2
CF
ADA4941
R1
R3
100nF
R5
R4
R6
05
79
2-
01
0
Figure 30. Single-Ended-to-Differential Driver Circuit
VOLTAGE REFERENCE INPUT
The AD7690 voltage reference input, REF, has a dynamic input
impedance and should therefore be driven by a low impedance
source with efficient decoupling between the REF and GND
pins, as explained in the Layout section.
When REF is driven by a very low impedance source (for
example, a reference buffer using the AD8031 or the AD8605),
a 10 μF (X5R, 0805 size) ceramic chip capacitor is appropriate
for optimum performance.
If an unbuffered reference voltage is used, the decoupling value
depends on the reference used. For instance, a 22 μF (X5R,
1206 size) ceramic chip capacitor is appropriate for optimum
performance using a low temperature drift ADR43x reference.
If desired, a reference-decoupling capacitor with a value as small
as 2.2 μF can be used with a minimal impact on performance,
especially DNL.
Regardless, there is no need for an additional lower value
ceramic decoupling capacitor (for example, 100 nF) between the
REF and GND pins.
相关PDF资料
PDF描述
MAX933CSA+T IC COMPARATOR W/REF 8-SOIC
VE-B1T-IV-F3 CONVERTER MOD DC/DC 6.5V 150W
VE-B1T-IV-F2 CONVERTER MOD DC/DC 6.5V 150W
MAX982CSA+T IC COMPARATOR OD 8-SOIC
AD7710ARZ IC ADC 24BIT DIFF INP 24-SOIC
相关代理商/技术参数
参数描述
AD7690BRMZ-RL7 功能描述:IC ADC 18BIT 400KSPS 10-MSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:PulSAR® 标准包装:1 系列:- 位数:14 采样率(每秒):83k 数据接口:串行,并联 转换器数目:1 功率耗散(最大):95mW 电压电源:双 ± 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:28-DIP(0.600",15.24mm) 供应商设备封装:28-PDIP 包装:管件 输入数目和类型:1 个单端,双极
AD7690BRNZ 制造商:Analog Devices 功能描述:
AD7691 制造商:AD 制造商全称:Analog Devices 功能描述:16-Bit Lower Power
AD76911 制造商:AD 制造商全称:Analog Devices 功能描述:18-Bit, 2 MSPS PulSAR 15 mW ADC in LFCSP (QFN)
AD7691BCPZ-R2 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: