- 您现在的位置：买卖IC网 > PDF目录10181 > AD7691BRMZ-RL7 (Analog Devices Inc)IC ADC 18BIT SAR 250KSPS 10-MSOP PDF资料下载
参数资料
| 型号： | AD7691BRMZ-RL7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 14/28页 |
| 文件大小： | 0K |
| 描述： | IC ADC 18BIT SAR 250KSPS 10-MSOP |
| 标准包装： | 1,000 |
| 系列： | PulSAR® |
| 位数： | 18 |
| 采样率（每秒）： | 250k |
| 数据接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 12.5mW |
| 电压电源： | 模拟和数字 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 10-MSOP |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 1 个差分，双极 |
| 配用： | EVAL-AD7691CBZ-ND - BOARD EVALUATION FOR AD7691CBZ |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
Data Sheet
AD7691
Rev. C | Page 21 of 28
CS MODE, 4-WIRE WITH BUSY INDICATOR
This mode is normally used when a single AD7691 is connected
to an SPI-compatible digital host with an interrupt input, and it
is desired to keep CNV, which is used to sample the analog
input, independent of the signal used to select the data reading.
This requirement is particularly important in applications
where low jitter on CNV is desired.
The connection diagram is shown in Figure 41, and the
corresponding timing is given in Figure 42.
With SDI high, a rising edge on CNV initiates a conversion,
selects the CS mode, and forces SDO to high impedance. In this
mode, CNV must be held high during the conversion phase and
the subsequent data readback. (If SDI and CNV are low, SDO is
driven low.) Prior to the minimum conversion time, SDI can be
used to select other SPI devices, such as analog multiplexers,
but SDI must be returned low before the minimum conversion
time elapses and then held low for the maximum possible
conversion time to guarantee the generation of the busy signal
indicator. When the conversion is complete, SDO goes from
high impedance to low impedance. With a pull-up on the SDO
line, this transition can be used as an interrupt signal to initiate
the data readback controlled by the digital host. The AD7691
then enters the acquisition phase and powers down. The data
bits are clocked out, MSB first, by subsequent SCK falling edges.
The data is valid on both SCK edges. Although the rising edge
can be used to capture the data, a digital host using the SCK
falling edge can allow a faster reading rate, provided it has an
acceptable hold time. After the optional 19th SCK falling edge,
or SDI going high, whichever occurs first, SDO returns to high
impedance.
DATA IN
IRQ
CLK
CONVERT
CS1
VIO
DIGITAL HOST
47k
CNV
SCK
SDO
SDI
AD7691
06
14
6-
01
7
Figure 41. 4-Wire CS Mode with Busy Indicator Connection Diagram
SDO
D17
D16
D1
D0
tDIS
SCK
1
2
3
171819
tSCK
tSCKL
tSCKH
tHSDO
tDSDO
tEN
CONVERSION
ACQUISITION
tCONV
tCYC
tACQ
ACQUISITION
SDI
CNV
tSSDICNV
tHSDICNV
06
14
6-
01
8
Figure 42. 4-Wire CS Mode with Busy Indicator Serial Interface Timing
相关PDF资料 |
PDF描述 |
|---|---|
| MS3106F24-22S | CONN PLUG 4POS STRAIGHT W/SCKT |
| VE-B7J-MY | CONVERTER MOD DC/DC 36V 50W |
| ADM3307EARUZ-REEL7 | IC TXRX RS-232 5:3 2.7V 28TSSOP |
| CXS3106A282P | CONN PLUG 14POS STRGHT PIN |
| LTC2850CDD#TRPBF | IC TXRX RS485 20MBPS 8-DFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7693 | 制造商:AD 制造商全称:Analog Devices 功能描述:16-Bit Lower Power |
| AD76931 | 制造商:AD 制造商全称:Analog Devices 功能描述:18-Bit, 2 MSPS PulSAR 15 mW ADC in LFCSP (QFN) |
| AD7693BCPZ | 制造商:Analog Devices 功能描述:ADC SGL SAR 500KSPS 16BIT SERL 10LFCSP - Rail/Tube |
| AD7693BCPZ-R2 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
| AD7693BCPZRL | 功能描述:IC ADC 16BIT 500KSPS 10LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:PulSAR® 标准包装:1 系列:- 位数:14 采样率（每秒）:83k 数据接口:串行，并联 转换器数目:1 功率耗散（最大）:95mW 电压电源:双 ± 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:28-DIP（0.600"，15.24mm） 供应商设备封装:28-PDIP 包装:管件 输入数目和类型:1 个单端，双极 |
发布紧急采购，3分钟左右您将得到回复。