- 您现在的位置：买卖IC网 > PDF目录10113 > AD7701AN (Analog Devices Inc)IC ADC 16BIT LC2MOS 20-DIP PDF资料下载
参数资料
| 型号： | AD7701AN |
| 厂商： | Analog Devices Inc |
| 文件页数： | 3/20页 |
| 文件大小： | 0K |
| 描述： | IC ADC 16BIT LC2MOS 20-DIP |
| 标准包装： | 18 |
| 位数： | 16 |
| 采样率（每秒）： | 4k |
| 数据接口： | 串行 |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 37mW |
| 电压电源： | 模拟和数字，双 ± |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 20-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 20-PDIP |
| 包装： | 管件 |
| 输入数目和类型： | 1 个单端，单极；1 个单端，双极 |
REV. E
AD7701
–11–
INPUT SIGNAL CONDITIONING
Reference voltages from 1 V to 3 V may be used with the AD7701
with little degradation in performance. Input ranges that cannot
be accommodated by this range of reference voltages may be
achieved by input signal conditioning. This may take the form
of gain to accommodate a smaller signal range, or passive attenua-
tion to reduce a larger input voltage range.
Source Resistance
If passive attenuators are used in front of the AD7701, care must
be taken to ensure that the source impedance is sufficiently low.
The AD7701 has an analog input with over 1 G
dc input
resistance. In parallel with this, there is a small dynamic load that
varies with the clock frequency (see Figure 13). Each time the
analog input is sampled, a 10 pF capacitor draws a charge packet
of maximum 1 pC (10 pF
× 100 mV) from the analog source
AIN
R1
R2
CEXT
AGND
AD7701
V OS 100mV
CIN
10pF
Figure 13. Equivalent Input Circuit and Input Attenuator
with a frequency fCLKIN/256. For a 4.096 MHz CLKIN, this
yields an average current draw of 16 nA. After each sample, the
AD7701 allows 62 clock periods for the input voltage to settle.
The equation that defines settling time is:
VV
e
OIN
tRC
=
[]
1
where
VO is the final settled value.
VIN is the value of the input signal.
R is the value of the input source resistance.
C is the 10 pF sample capacitor.
t is equal to 62/fCLKIN.
From this, the following equation can be developed, which
gives the maximum allowable source resistance, RS(MAX), for
an error of VE:
RS (MAX )
=
62
fCLKIN
×(10 pF)× ln(100mV /V
E )
Provided the source resistance is less than this value, the analog
input will settle within the desired error band in the requisite 62
clock periods. Insufficient settling leads to offset errors. These
can be calibrated in system calibration schemes.
If a limit of 10
V (0.25 LSB at 16 bits) is set for the maximum
offset voltage, then the maximum allowable source resistance is
160 k
from the above equation, assuming that there is no
external stray capacitance.
An RC filter may be added in front of the AD7701 to reduce
high frequency noise. With an external capacitor added from
AIN to AGND, the following equation will specify the maximum
allowable source resistance:
RS (Max) =
62
f CLKIN ×(CIN + CEXT )× ln
100 mV
× C
IN /( CIN + CEXT )
V
E
The practical limit to the maximum value of source resistance is
thermal (Johnson) noise. A practical resistor may be modeled as
an ideal (noiseless) resistor in series with a noise voltage source
or in parallel with a noise current source:
V
kTRf Volts
n
= 4
i
kTRf R Amperes
n
= 4
where
k is Boltzmann’s constant (1.38
× 10–23 J/K).
T is temperature in degrees Kelvin (
°C + 273).
Active signal conditioning circuits such as op amps generally do
not suffer from problems of high source impedance. Their open-
loop output resistance is normally only tens of ohms and, in any
case, most modern general-purpose op amps have sufficiently
fast closed-loop settling time for this not to be a problem. Offset
voltage in op amps can be eliminated in a system calibration
routine. With the wide dynamic range and small LSB size of the
AD7701, noise can also be a problem, but the digital filter will
reject most broadband noise above its cutoff frequency. How-
ever, in certain applications there may be a need for analog
input filtering.
Antialias Considerations
The digital filter of the AD7701 does not provide any rejection
at integer multiples of the sampling frequency (nfCLKlN/256,
where n = 1, 2, 3 . . . ).
With a 4.096 MHz master clock, there are narrow (
± 10 Hz)
bands at 16 kHz, 32 kHz, 48 kHz, and so on, where noise
passes unattenuated to the output.
However, due to the AD7701’s high oversampling ratio of 800
(16 kHz to 20 Hz), these bands occupy only a small fraction of
the spectrum and most broadband noise is filtered. The reduc-
tion in broadband noise is given by:
eOUT
= e
IN
2 f C / f S
= 0.035 e
IN
where
elN and eOUT are rms noise terms referred to the input.
fC is the filter –3 dB corner frequency (fCLKIN/409600).
fS is the sampling frequency (fCLKIN/256).
Since the ratio of fS to fCLKIN is fixed, the digital filter reduces
broadband white noise by 96.5% independent of the master
clock frequency.
相关PDF资料 |
PDF描述 |
|---|---|
| MS3102R36-4S | CONN RCPT 3POS BOX MNT W/SCKT |
| MS3102E36-4S | CONN RCPT 3POS BOX MNT W/SCKT |
| MS3106R16-9S | CONN PLUG 4POS STRAIGHT W/SCKT |
| LT1785HS8#PBF | IC TXRX RS485/RS422 60V 8-SOIC |
| LTC1608AIG#TR | IC CONV A/D 16BIT 500KSPS 36SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7701ANZ | 功能描述:IC ADC 16BIT LC2MOS 20-DIP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:microPOWER™ 位数:8 采样率（每秒）:1M 数据接口:串行，SPI? 转换器数目:1 功率耗散（最大）:- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘（4x4） 包装:Digi-Reel® 输入数目和类型:8 个单端，单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6 |
| AD7701AQ | 制造商:AD 制造商全称:Analog Devices 功能描述:LC2MOS 16-Bit A/D Converter |
| AD7701AR | 功能描述:IC ADC 16BIT LC2MOS 20-SOIC RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:- 位数:14 采样率（每秒）:83k 数据接口:串行，并联 转换器数目:1 功率耗散（最大）:95mW 电压电源:双 ± 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:28-DIP（0.600"，15.24mm） 供应商设备封装:28-PDIP 包装:管件 输入数目和类型:1 个单端，双极 |
| AD7701AR-REEL | 制造商:Rochester Electronics LLC 功能描述:- Tape and Reel |
| AD7701ARS | 功能描述:IC ADC 16BIT LC2MOS MONO 28-SSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:- 位数:14 采样率（每秒）:83k 数据接口:串行，并联 转换器数目:1 功率耗散（最大）:95mW 电压电源:双 ± 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:28-DIP（0.600"，15.24mm） 供应商设备封装:28-PDIP 包装:管件 输入数目和类型:1 个单端，双极 |
发布紧急采购，3分钟左右您将得到回复。