- 您现在的位置：买卖IC网 > PDF目录10113 > AD7701AN (Analog Devices Inc)IC ADC 16BIT LC2MOS 20-DIP PDF资料下载
参数资料
| 型号： | AD7701AN |
| 厂商： | Analog Devices Inc |
| 文件页数： | 8/20页 |
| 文件大小： | 0K |
| 描述： | IC ADC 16BIT LC2MOS 20-DIP |
| 标准包装： | 18 |
| 位数： | 16 |
| 采样率（每秒）： | 4k |
| 数据接口： | 串行 |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 37mW |
| 电压电源： | 模拟和数字，双 ± |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 20-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 20-PDIP |
| 包装： | 管件 |
| 输入数目和类型： | 1 个单端，单极；1 个单端，双极 |
REV. E
–16–
AD7701
Asynchronous Communications (AC) Mode
The AC mode (MODE pin tied to –5 V) offers a UART com-
patible interface that allows the AD7701 to transmit data
asynchronously from remote locations. An external SCLK sets
the baud rate and data is transmitted in two bytes in UART
compatible format. Using the AC mode, the AD7701 can be
interfaced directly to microprocessors with UART interfaces,
such as the 8051 and TMS70X2.
Data transmission is initiated by
CS going low. If CS is low on a
falling edge of SCLK, the AD7701 begins transmitting an 8-bit
data byte (DB8 to DB15) with one start bit and two stop bits,
as in Figure 21. The SDATA output will then go three-state.
The second byte is transmitted by bringing
CS low again and
DB0 to DB7 are transmitted in the same format as the first byte.
UART baud rates are typically low compared to the AD7701’s
4 kHz output update rate. If
CS is low and data is still being
transmitted when a new data-word becomes available, the new
data will be ignored. However, if
CS has been taken high between
bytes, when a new data-word becomes available, the AD7701
could update the output register before the second byte is trans-
mitted. In this case, the UART would receive the first byte of
the new word instead of the second byte of the old word. When
using the AC mode, care must obviously be taken to ensure that
this does not occur.
DIGITAL NOISE AND OUTPUT LOADING
As mentioned earlier, the AD7701 divides its internal timing
into two distinct phases, analog sampling and settling and digi-
tal computation. In the SSC mode, data is transmitted only
during the digital computation periods to minimize the effects
of digital noise on analog performance. In the SEC and AC
modes, data transmission is externally controlled, so this auto-
matic safeguard does not exist.
Whatever mode of operation is used, resistive and capacitive
loads on digital outputs should be minimized in order to reduce
crosstalk between analog and digital portions of the circuit. For
this reason, connection to low power CMOS logic such as one
of the 4000 series or 74C families is recommended.
It is especially important to minimize the load on SDATA in the
AC mode, as transmission in this mode is inherently asynchro-
nous. In the SEC mode, the AD7701 should be synchronized to
the digital system clock via CLKIN.
SCLK (I)
SDATA (O)
DB9
START
BIT
DB8
DB14
DB15
STOP
BIT
DB0
DB1
DB6
DB7
HI-Z
STOP
BIT
START
BIT
STOP
BIT
STOP
BIT
DRDY (O)
CS (I)
Figure 21. Timing Diagram for Asynchronous Communications Mode
相关PDF资料 |
PDF描述 |
|---|---|
| MS3102R36-4S | CONN RCPT 3POS BOX MNT W/SCKT |
| MS3102E36-4S | CONN RCPT 3POS BOX MNT W/SCKT |
| MS3106R16-9S | CONN PLUG 4POS STRAIGHT W/SCKT |
| LT1785HS8#PBF | IC TXRX RS485/RS422 60V 8-SOIC |
| LTC1608AIG#TR | IC CONV A/D 16BIT 500KSPS 36SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7701ANZ | 功能描述:IC ADC 16BIT LC2MOS 20-DIP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:microPOWER™ 位数:8 采样率（每秒）:1M 数据接口:串行，SPI? 转换器数目:1 功率耗散（最大）:- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘（4x4） 包装:Digi-Reel® 输入数目和类型:8 个单端，单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6 |
| AD7701AQ | 制造商:AD 制造商全称:Analog Devices 功能描述:LC2MOS 16-Bit A/D Converter |
| AD7701AR | 功能描述:IC ADC 16BIT LC2MOS 20-SOIC RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:- 位数:14 采样率（每秒）:83k 数据接口:串行，并联 转换器数目:1 功率耗散（最大）:95mW 电压电源:双 ± 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:28-DIP（0.600"，15.24mm） 供应商设备封装:28-PDIP 包装:管件 输入数目和类型:1 个单端，双极 |
| AD7701AR-REEL | 制造商:Rochester Electronics LLC 功能描述:- Tape and Reel |
| AD7701ARS | 功能描述:IC ADC 16BIT LC2MOS MONO 28-SSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:- 位数:14 采样率（每秒）:83k 数据接口:串行，并联 转换器数目:1 功率耗散（最大）:95mW 电压电源:双 ± 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:28-DIP（0.600"，15.24mm） 供应商设备封装:28-PDIP 包装:管件 输入数目和类型:1 个单端，双极 |
发布紧急采购，3分钟左右您将得到回复。