- 您现在的位置：买卖IC网 > PDF目录10527 > AD7711AARZ (Analog Devices Inc)IC ADC 24BIT RTD I SOURCE 24SOIC PDF资料下载
参数资料
| 型号： | AD7711AARZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 28/28页 |
| 文件大小： | 0K |
| 描述： | IC ADC 24BIT RTD I SOURCE 24SOIC |
| 标准包装： | 1 |
| 位数： | 24 |
| 采样率（每秒）： | 1.03k |
| 数据接口： | 串行 |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 52.5mW |
| 电压电源： | 模拟和数字，双 ± |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 24-SOIC W |
| 包装： | 管件 |
| 输入数目和类型： | 2 个差分，单极；2 个差分，双极 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页当前第28页
2
AD7711A
–9–
REV. D
Control Register (24 Bits)
A write to the device with the A0 input low writes data to the control register. A read to the device with the A0 input low accesses the
contents of the control register. The control register is 24 bits wide and when writing to the register 24 bits of data must be written;
otherwise the data will not be loaded to the control register. In other words, it is not possible to write just the first 12 bits of data into
the control register. If more than 24 clock pulses are provided before
TFS returns high, then all clock pulses after the 24th clock
pulse are ignored. Similarly, a read operation from the control register should access 24 bits of data.
MSB
MD2
MD1
MD0
G2
G1
G0
CH
PD
WL
IO
BO
B/U
FS11
* FS10
FS9
FS8
FS7
FS6
FS5
FS4
FS3
FS2
FS1
FS0
*Must always be 0 to ensure correct operation of the device.
FS0
Operating Mode
MD2
MD1
MD0
Operating Mode
00
0Normal Mode. This is the normal mode of operation of the device whereby a read to the device with A0
high accesses data from the data register. This is the default condition of these bits after the internal
power-on reset.
00
1Activate Self-Calibration. This activates self-calibration on the channel selected by CH. This is a one-step
calibration sequence, and when complete, the part returns to normal mode (with MD2, MD1, MD0 of
the control register returning to 0, 0, 0). The
DRDY output indicates when this self-calibration is complete
and valid data is available in the output register. For this calibration type, the zero-scale calibration is done
internally on shorted (zeroed) inputs, and the full-scale calibration is done internally on VREF.
01
0Activate System Calibration. This activates system calibration on the channel selected by CH. This is a
two-step calibration sequence, with the zero-scale calibration done first on the selected input channel and
DRDY indicating when this zero-scale calibration is complete. The part returns to normal mode at the
end of this first step in the two-step sequence.
01
1Activate System Calibration. This is the second step of the system calibration sequence with full-scale
calibration being performed on the selected input channel. Once again,
DRDY indicates when the full-
scale calibration is complete. When this calibration is complete, the part returns to normal mode.
10
0Activate System Offset Calibration. This activates system offset calibration on the channel selected by
CH. This is a one-step calibration sequence and, when complete, the part returns to normal mode with
DRDY indicating when this system offset calibration is complete. For this calibration type, the zero-scale
calibration is done on the selected input channel, and the full-scale calibration is done internally on VREF.
10
1Activate Background Calibration. This activates background calibration on the channel selected by CH. If
the background calibration mode is on, then the AD7711A provides continuous self-calibration of the
reference and shorted (zeroed) inputs. This calibration takes place as part of the conversion sequence,
extending the conversion time and reducing the word rate by a factor of 6. Its major advantage is that
the user does not have to worry about recalibrating the device when there is a change in the ambient
temperature. In this mode, the shorted (zeroed) inputs and VREF, as well as the analog input voltage, are
continuously monitored, and the calibration registers of the device are automatically updated.
11
0Read/Write Zero-Scale Calibration Coefficients. A read to the device with A0 high accesses the contents
of the zero-scale calibration coefficients of the channel selected by CH. A write to the device with A0 high
writes data to the zero-scale calibration coefficients of the channel selected by CH. The word length for
reading and writing these coefficients is 24 bits, regardless of the status of the WL bit of the control
register. Therefore, when writing to the calibration register 24 bits of data must be written; otherwise the
new data will not be transferred to the calibration register.
11
1Read/Write Full-Scale Calibration Coefficients. A read to the device with A0 high accesses the contents of
the full-scale calibration coefficients of the channel selected by CH. A write to the device with A0 high
writes data to the full-scale calibration coefficients of the channel selected by CH. The word length for
reading and writing these coefficients is 24 bits, regardless of the status of the WL bit of the control
register. Therefore, when writing to the calibration register, 24 bits of data must be written; otherwise the
new data will not be transferred to the calibration register.
相关PDF资料 |
PDF描述 |
|---|---|
| ICL3227EIAZA | IC TXRX SGL RS232 3-5.5V 16SSOP |
| AD7880CRZ | IC ADC 12BIT MONO LP 24-SOIC |
| AD9238BCPZ-65 | IC ADC 12BIT DUAL 65MSPS 64LFCSP |
| AD9238BSTZ-65 | IC ADC 12BIT DUAL 65MSPS 64-LQFP |
| ICL3226ECA | IC TXRX RS-232 3-5.5V ESD 16SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7711AN | 功能描述:IC ADC 24BIT RTD I SOURCE 24-DIP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 位数:12 采样率（每秒）:3M 数据接口:- 转换器数目:- 功率耗散（最大）:- 电压电源:- 工作温度:- 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-23-6 包装:带卷 (TR) 输入数目和类型:- |
| AD7711ANZ | 功能描述:IC ADC 24BIT RTD I SOURCE 24-DIP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 其它有关文件:TSA1204 View All Specifications 标准包装:1 系列:- 位数:12 采样率（每秒）:20M 数据接口:并联 转换器数目:2 功率耗散（最大）:155mW 电压电源:模拟和数字 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-TQFP 供应商设备封装:48-TQFP（7x7） 包装:Digi-Reel® 输入数目和类型:4 个单端，单极；2 个差分，单极 产品目录页面:1156 (CN2011-ZH PDF) 其它名称:497-5435-6 |
| AD7711ANZ | 制造商:Analog Devices 功能描述:IC ADC 24-BIT SIGMA DELTA |
| AD7711AQ | 功能描述:IC ADC 24BIT RTD I SOURCE 24CDIP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:- 位数:14 采样率（每秒）:83k 数据接口:串行，并联 转换器数目:1 功率耗散（最大）:95mW 电压电源:双 ± 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:28-DIP（0.600"，15.24mm） 供应商设备封装:28-PDIP 包装:管件 输入数目和类型:1 个单端，双极 |
| AD7711AR | 功能描述:IC ADC 24BIT RTD I SOURCE 24SOIC RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:- 位数:14 采样率（每秒）:83k 数据接口:串行，并联 转换器数目:1 功率耗散（最大）:95mW 电压电源:双 ± 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:28-DIP（0.600"，15.24mm） 供应商设备封装:28-PDIP 包装:管件 输入数目和类型:1 个单端，双极 |
发布紧急采购，3分钟左右您将得到回复。