- 您现在的位置：买卖IC网 > PDF目录10296 > AD7813YNZ (Analog Devices Inc)IC ADC 10BIT PARALLEL 16-DIP PDF资料下载
参数资料
| 型号： | AD7813YNZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 9/11页 |
| 文件大小： | 0K |
| 描述： | IC ADC 10BIT PARALLEL 16-DIP |
| 标准包装： | 25 |
| 位数： | 10 |
| 采样率（每秒）： | 400k |
| 数据接口： | 并联 |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 17.5mW |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 16-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 16-PDIP |
| 包装： | 管件 |
| 输入数目和类型： | 1 个单端，单极 |
AD7813
–7–
REV. C
During the acquisition phase the sampling capacitor must be
charged to within a 1/2 LSB of its final value. The time it takes
to charge the sampling capacitor (TCHARGE) is given by the
following formula:
TCHARGE = 7.6
× (R2 + 125 ) × 3.5 pF
For small values of source impedance, the settling time associ-
ated with the sampling circuit (100 ns) is, in effect, the acquisi-
tion time of the ADC. For example, with a source impedance
(R2) of 10
the charge time for the sampling capacitor is
approximately 4 ns. The charge time becomes significant for
source impedances of 2 k
and greater.
AC Acquisition Time
In ac applications it is recommended to always buffer analog
input signals. The source impedance of the drive circuitry must
be kept as low as possible to minimize the acquisition time of
the ADC. Large values of source impedance will cause the
THD to degrade at high throughput rates.
ADC TRANSFER FUNCTION
The output coding of the AD7813 is straight binary. The
designed code transitions occur at successive integer LSB values
(i.e., 1 LSB, 2 LSBs, etc.). The LSB size is = VREF/1024. The
ideal transfer characteristic for the AD7813 is shown in Figure 7.
000...000
0V
ANALOG INPUT
111...111
000...001
000...010
111...110
111...000
011...111
1LSB
+VREF–1LSB
1LSB = VREF/1024
ADC
CODE
Figure 7. Transfer Characteristic
POWER-UP TIMES
The AD7813 has a 1.5
s power-up time. When VDD is first
connected, the AD7813 is in a low current mode of operation.
In order to carry out a conversion the AD7813 must first be
powered up. The ADC is powered up by a rising edge on an
internally generated CONVST signal, which occurs as a result
of a rising edge on the external CONVST pin. The rising edge
of the external CONVST signal initiates a 1.5
s pulse on the
internal CONVST signal. This pulse is present to ensure the
part has enough time to power up before a conversion is initi-
ated, as a conversion is initiated on the falling edge of gated
CONVST. See Timing and Control section. Care must be taken
to ensure that the CONVST pin of the AD7813 is logic low
when VDD is first applied.
When operating in Mode 2, the ADC is powered down at the
end of each conversion and powered up again before the next
conversion is initiated. (See Figure 8.)
t POWER-UP
1.5 s
t POWER-UP
1.5 s
t POWER-UP
1.5 s
MODE 1
MODE 2
VDD
EXT
CONVST
INT
CONVST
VDD
EXT
CONVST
INT
CONVST
Figure 8. Power-Up Times
POWER VS. THROUGHPUT RATE
By operating the AD7813 in Mode 2, the average power con-
sumption of the AD7813 decreases at lower throughput rates.
Figure 9 shows how the Automatic Power-Down is implemented
using the external CONVST signal to achieve the optimum
power performance for the AD7813. The AD7813 is operated
in Mode 2, and the duration of the external CONVST pulse is
set to be equal to or less than the power-up time of the device.
As the throughput rate is reduced, the device remains in its power-
down state longer and the average power consumption over time
drops accordingly.
EXT
CONVST
INT
CONVST
POWER-DOWN
t POWER-UP
1.5 s
t CONVERT
2.3 s
t CYCLE
100 s @ 10kSPS
Figure 9. Automatic Power-Down
For example, if the AD7813 is operated in a continuous sam-
pling mode, with a throughput rate of 10 kSPS, the power con-
sumption is calculated as follows. The power dissipation during
normal operation is 10.5 mW, VDD = 3 V. If the power-up time
is 1.5
s and the conversion time is 2.3 s, the AD7813 can then
be said to dissipate 10.5 mW for 3.8
s (worst-case) during each
conversion cycle. If the throughput rate is 10 kSPS, the cycle
time is 100
s and the average power dissipated during each
cycle is (3.8/100)
× (10.5 mW) = 400 W.
相关PDF资料 |
PDF描述 |
|---|---|
| AD7708BRZ-REEL7 | IC ADC 16BIT R-R 8/10CH 28SOIC |
| CS3100A-14S-78P | CONN RCPT 2POS WALL MNT W/PINS |
| AD7366BRUZ-5-RL7 | IC ADC 12BIT DUAL BIPO 24-TSSOP |
| MS27467E21B11BA | CONN HSG PLUG 11POS STRGHT SCKT |
| D38999/26MD19SNLC | CONN HSG PLUG 19POS STRGHT SCKT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7813YR | 制造商:Analog Devices 功能描述:ADC Single SAR 400ksps 10-bit Parallel 16-Pin SOIC N 制造商:Analog Devices 功能描述:IC 10-BIT ADC |
| AD7813YR-REEL | 制造商:Analog Devices 功能描述:ADC Single SAR 400ksps 10-bit Parallel 16-Pin SOIC N T/R |
| AD7813YR-REEL7 | 制造商:Analog Devices 功能描述:ADC Single SAR 400ksps 10-bit Parallel 16-Pin SOIC N T/R |
| AD7813YRU | 功能描述:IC ADC 10BIT PARALLEL 16-TSSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 位数:12 采样率（每秒）:3M 数据接口:- 转换器数目:- 功率耗散（最大）:- 电压电源:- 工作温度:- 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-23-6 包装:带卷 (TR) 输入数目和类型:- |
| AD7813YRU-REEL | 制造商:Analog Devices 功能描述:ADC Single SAR 400ksps 10-bit Parallel 16-Pin TSSOP T/R 制造商:Analog Devices 功能描述:ADC SGL SAR 400KSPS 10-BIT PARALLEL 16TSSOP - Tape and Reel |
发布紧急采购，3分钟左右您将得到回复。