- 您现在的位置：买卖IC网 > PDF目录10289 > AD7829BRW-1RL7 (Analog Devices Inc)IC ADC 8BIT 8CH 2MSPS 28-SOIC PDF资料下载
参数资料
| 型号： | AD7829BRW-1RL7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 10/20页 |
| 文件大小： | 0K |
| 描述： | IC ADC 8BIT 8CH 2MSPS 28-SOIC |
| 标准包装： | 400 |
| 位数： | 8 |
| 采样率（每秒）： | 2M |
| 数据接口： | 并联 |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 36mW |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 28-SOIC W |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 8 个单端，单极 |
AD7829-1
Rev. 0 | Page 18 of 20
MICROPROCESSOR INTERFACING
PSP0 TO PSP7
RD
INT
PIC16C6x/7x1
DB0 TO DB7
RD
EOC
CS
1ADDITIONAL PINS OMITTED FOR CLARITY.
CS
AD7829-11
06179-
026
The parallel port on the AD7829-1 allows the ADCs to be
interfaced to a range of many different microcontrollers. This
section explains how to interface the AD7829-1 with some of
the more common microcontroller parallel interface protocols.
AD7829-1 TO 8051
Figure 24 shows a parallel interface between the AD7829-1 and
the 8051 microcontroller. The EOC signal on the AD7829-1
provides an interrupt request to the 8051 when a conversion
ends and data is ready. Port 0 of the 8051 can serve as an input
or output port, or, as in this case when used together with the
address latch enable (ALE) of the AD8051, it can be used as a
bidirectional low order address and data bus. The ALE output
of the 8051 is used to latch the low byte of the address during
accesses to the device, while the high order address byte is
supplied from Port 2. Port 2 latches remain stable when the
AD7829-1 is addressed, because they do not have to be turned
around (set to 1) for data input, as is the case for Port 0.
Figure 25. Interfacing to the PIC16C6x/PIC16C7x
AD7829-1 TO ADSP-21xx
Figure 26 shows a parallel interface between the AD7829-1 and
the ADSP-21xx series of DSPs. As before, the EOC signal on the
AD7829-1 provides an interrupt request to the DSP when a
conversion ends.
AD0 TO AD7
ALE
A8 TO A15
RD
INT
80511
LATCH
DECODER
DB0 TO DB7
RD
EOC
CS
1ADDITIONAL PINS OMITTED FOR CLARITY.
AD7829-11
061
79-
0
25
D7 TO D0
RD
IRQ
ADSP-21xx1
DB0 TO DB7
RD
EOC
CS
1ADDITIONAL PINS OMITTED FOR CLARITY.
DMS
EN
ADDRESS
DECODE
LOGIC
A13 TO A0
06179-
027
AD7829-11
Figure 24. Interfacing to the 8051
Figure 26. Interfacing to the ADSP-21xx
AD7829-1 TO PIC16C6x/PIC16C7x
INTERFACING MULTIPLEXER ADDRESS INPUTS
Figure 25 shows a parallel interface between the AD7829-1 and
the PIC16C64/PIC16C65/PIC16C74. The
Figure 27 shows a simplified interfacing scheme between the
AD7829-1 and any microprocessor or microcontroller that
facilitates easy channel selection on the ADCs. The multiplexer
address is latched on the falling edge of the
EOC signal on the
AD7829-1 provides an interrupt request to the microcontroller
when a conversion begins. Of the PIC16C6x/PIC16C7x range of
microcontrollers, only the PIC16C64/PIC16C65/PIC16C74 can
provide the option of a parallel slave port. Port D of the micro-
controller operates as an 8-bit wide parallel slave port when Control
Bit PSPMODE in the TRISE register is set. Setting PSPMODE
enables Port Pin RE0 to be the
RD signal, as outlined
in the Parallel Interface section, which allows the use of the three
LSBs of the address bus to select the channel address. As shown in
Figure 27, only Address Bit A3 to Address Bit A15 are address
decoded, allowing A0 to A2 to be changed according to desired
channel selection without affecting chip selection.
RD
CS
output and RE2 to be the
(chip select) output. For this functionality, the corresponding
data direction bits of the TRISE register must be configured as
outputs (reset to 0). See the PIC16C6x/PIC16C7x Microcontroller
User Manual for more information.
相关PDF资料 |
PDF描述 |
|---|---|
| D38999/26JG39SNLC | CONN HSG PLUG 39POS STRGHT SCKT |
| D38999/20JG11PNLC | CONN HSG RCPT 11POS WALL MT PINS |
| LTC1407HMSE#PBF | IC ADC 12BIT 3MSPS 10-MSOP |
| LTC1850CFW | IC ADC 10BIT 1.25MSPS 48-TSSOP |
| MS27499E16F8P | CONN RCPT 8POS BOX MNT W/PINS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7829BRWZ-1 | 功能描述:IC ADC 8BIT 8CH 2MSPS 28-SOIC RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| AD7829BRWZ-1RL7 | 功能描述:IC ADC 8BIT 8CH 2MSPS 28-SOIC RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| AD7829BRZ | 功能描述:IC ADC 8BIT 8CH 2MSPS 28-SOIC RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:microPOWER™ 位数:8 采样率（每秒）:1M 数据接口:串行，SPI? 转换器数目:1 功率耗散（最大）:- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘（4x4） 包装:Digi-Reel® 输入数目和类型:8 个单端，单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6 |
| AD7829BRZ1 | 制造商:AD 制造商全称:Analog Devices 功能描述:3 V/5 V, 2 MSPS, 8-Bit, 1-/4-/8-Channel Sampling ADCs |
| AD7829BRZ-REEL | 功能描述:IC ADC 8BIT 8CH 2MSPS 28-SOIC RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
发布紧急采购，3分钟左右您将得到回复。