- 您现在的位置：买卖IC网 > PDF目录10184 > AD7854AR (Analog Devices Inc)IC ADC 12BIT PARALLEL LP 28-SOIC PDF资料下载
参数资料
| 型号： | AD7854AR |
| 厂商： | Analog Devices Inc |
| 文件页数： | 19/28页 |
| 文件大小： | 0K |
| 描述： | IC ADC 12BIT PARALLEL LP 28-SOIC |
| 标准包装： | 27 |
| 位数： | 12 |
| 采样率（每秒）： | 200k |
| 数据接口： | 并联 |
| 转换器数目： | 2 |
| 功率耗散（最大）： | 30mW |
| 电压电源： | 模拟和数字 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 28-SOIC W |
| 包装： | 管件 |
| 输入数目和类型： | 1 个伪差分，单极；1 个伪差分，双极 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
AD7854/AD7854L
–26–
REV. B
APPLICATION HINTS
Grounding and Layout
The analog and digital supplies of the AD7854/AD7854L are
independent and separately pinned out to minimize coupling
between the analog and digital sections of the device. The part
has very good immunity to noise on the power supplies as can
be seen by the PSRR versus frequency graph. However, care
should still be taken with regard to grounding and layout.
The printed circuit board on which the AD7854/AD7854L is
mounted should be designed such that the analog and digital
sections are separated and confined to certain areas of the
board. This facilitates the use of ground planes that can be
easily separated. A minimum etch technique is generally best
for ground planes as it gives the best shielding. Digital and
analog ground planes should only be joined in one place. If
the AD7854/AD7854L is the only device requiring an AGND
to DGND connection, then the ground planes should be
connected at the AGND and DGND pins of the AD7854/
AD7854L. If the AD7854/AD7854L is in a system where
multiple devices require AGND to DGND connections, the
connection should still be made at one point only, a star ground
point which should be established as close as possible to the
AD7854/AD7854L.
Avoid running digital lines under the device as these couple
noise onto the die. The analog ground plane should be allowed
to run under the AD7854/AD7854L to avoid noise coupling.
The power supply lines to the AD7854/AD7854L should use as
large a trace as possible to provide low impedance paths and
reduce the effects of glitches on the power supply line. Fast
switching signals like clocks and the data inputs should be
shielded with digital ground to avoid radiating noise to other
sections of the board and clock signals should never be run near
the analog inputs. Avoid crossover of digital and analog signals.
Traces on opposite sides of the board should run at right angles
to each other. This reduces the effects of feedthrough through
the board. A microstrip technique is by far the best but is not
always possible with a double-sided board. In this technique,
the component side of the board is dedicated to ground planes
while signals are placed on the solder side.
Good decoupling is also important. All analog supplies should
be decoupled with a 10
F tantalum capacitor in parallel with
0.1
F disc ceramic capacitor to AGND. All digital supplies
should have a 0.1
F disc ceramic capacitor to DGND. To
achieve the best performance from these decoupling compo-
nents, they must be placed as close as possible to the device,
ideally right up against the device. In systems where a common
supply voltage is used to drive both the AVDD and DVDD of the
AD7854/AD7854L, it is recommended that the system’s AVDD
supply is used. In this case an optional 10
resistor between
the AVDD pin and DVDD pin can help to filter noise from digital
circuitry. This supply should have the recommended analog
supply decoupling capacitors between the AVDD pin of the
AD7854/AD7854L and AGND and the recommended digital
supply decoupling capacitor between the DVDD pin of the
AD7854/AD7854L and DGND.
Evaluating the AD7854/AD7854L Performance
The recommended layout for the AD7854/AD7854L is outlined
in the evaluation board for the AD7854/AD7854L. The evalua-
tion board package includes a fully assembled and tested
evaluation board, documentation, and software for controlling
the board from the PC via the EVAL-CONTROL BOARD.
The EVAL-CONTROL BOARD can be used in conjunction
with the AD7854/AD7854L Evaluation board, as well as many
other Analog Devices evaluation boards ending in the CB desig-
nator, to demonstrate/evaluate the ac and dc performance of the
AD7854/AD7854L.
The software allows the user to perform ac (fast Fourier trans-
form) and dc (histogram of codes) tests on the AD7854/
AD7854L. It also gives full access to all the AD7854/AD7854L
on-chip registers allowing for various calibration and power-
down options to be programmed.
AD785x Family
All parts are 12 bits, 200 kSPS, 3.0 V to 5.5 V.
AD7853 – Single Channel Serial
AD7854 – Single Channel Parallel
AD7858 – Eight Channel Serial
AD7859 – Eight Channel Parallel
相关PDF资料 |
PDF描述 |
|---|---|
| ADM3312EARUZ-REEL | IC TXRX RS-232 3:3 2.7V 24TSSOP |
| VE-25K-IU-F3 | CONVERTER MOD DC/DC 40V 200W |
| VI-2NH-CU-F3 | CONVERTER MOD DC/DC 52V 200W |
| VI-263-IW-S | CONVERTER MOD DC/DC 24V 100W |
| MS27468T15F18SB | CONN RCPT 18POS JAM NUT W/SCKT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7854AR-REEL | 制造商:Analog Devices 功能描述:ADC Single SAR 200ksps 12-bit Parallel 28-Pin SOIC W T/R 制造商:Analog Devices 功能描述:ADC SGL SAR 200KSPS 12-BIT PARALLEL 28SOIC W - Tape and Reel |
| AD7854ARS | 功能描述:IC ADC 12BIT PARALLEL LP 28-SSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极 |
| AD7854ARS-REEL | 功能描述:IC ADC 12BIT PARALLEL LP 28-SSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极 |
| AD7854ARSZ | 功能描述:IC ADC 12BIT PARALLEL LP 28-SSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 其它有关文件:TSA1204 View All Specifications 标准包装:1 系列:- 位数:12 采样率（每秒）:20M 数据接口:并联 转换器数目:2 功率耗散（最大）:155mW 电压电源:模拟和数字 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-TQFP 供应商设备封装:48-TQFP（7x7） 包装:Digi-Reel® 输入数目和类型:4 个单端，单极；2 个差分，单极 产品目录页面:1156 (CN2011-ZH PDF) 其它名称:497-5435-6 |
| AD7854ARZ | 功能描述:IC ADC 12BIT PARALLEL LP 28SOIC RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极 |
发布紧急采购，3分钟左右您将得到回复。