- 您现在的位置：买卖IC网 > PDF目录1984 > AD7864BSZ-1REEL (Analog Devices Inc)IC ADC 12BIT DUAL 4CHAN 44-MQFP PDF资料下载
参数资料
| 型号： | AD7864BSZ-1REEL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 3/28页 |
| 文件大小： | 0K |
| 描述： | IC ADC 12BIT DUAL 4CHAN 44-MQFP |
| 标准包装： | 800 |
| 位数： | 12 |
| 采样率（每秒）： | 520k |
| 数据接口： | 并联 |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 120mW |
| 电压电源： | 模拟和数字 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 44-QFP |
| 供应商设备封装： | 44-MQFP（10x10） |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 4 个差分，双极 |
第1页第2页当前第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
AD7864
Rev. D | Page 11 of 28
THEORY OF OPERATION
CONVERTER DETAILS
The AD7864 is a high speed, low power, 4-channel simultaneous
sampling 12-bit ADC that operates from a single 5 V supply.
The part contains a 1.65 μs successive approximation ADC, four
track-and-hold amplifiers, an internal 2.5 V reference, and a
high speed parallel interface. There are four analog inputs that
can be simultaneously sampled, thus preserving the relative
phase information of the signals on all four analog inputs.
Thereafter, conversions are completed on the selected subset of
the four channels. The part accepts an analog input range of
±10 V or ±5 V (AD7864-1), ±2.5 V (AD7864-3), and 0 V to
+2.5 V or 0 V to +5 V (AD7864-2). Overvoltage protection on
the analog inputs of the part allows the input voltage to go to
±20 V, (AD7864-1 ±10 V range), 7 V or +20 V (AD7864-1
±5 V range), 1 V to +20 V (AD7864-2), and 7 V to +20 V
(AD7864-3), without causing damage. The AD7864 has two
operating modes: reading-between-conversions and reading-
after-the-conversion sequence. These modes are discussed in
more detail in the Timing
and Control section.
A conversion is initiated on the AD7864 by pulsing the CONVST
input. On the rising edge of CONVST, all four on-chip track-
and-holds are placed into hold simultaneously and the conversion
sequence is started on all the selected channels. Channel selection
is made via the SL1 to SL4 pins if H/S SEL is Logic 0 or via the
channel select register if H/S SEL is Logic 1—see the
section. The channel select register is
programmed via the bidirectional data lines (DB0 to DB3) and
a standard write operation. The selected conversion sequence is
latched on the rising edge of
CONVST, therefore, changing a
selection only takes effect once a new conversion sequence is
initiated. The BUSY output signal is triggered high on the rising
edge of CONVST and remains high for the duration of the conver-
sion sequence. The conversion clock for the part is generated
internally using a laser trimmed, clock oscillator circuit.
There is also the option of using an external clock, by tying the
INT/EXT CLK pin logic high, and applying an external clock to
the CLKIN pin. However, the optimum throughput is obtained
by using the internally generated clock—see the
section. The
EOC signal indicates the end of
each conversion in the conversion sequence. The BUSY signal
indicates the end of the full conversion sequence, and at this
time, all four track and holds return to tracking mode. The
conversion results can be read either at the end of the full
conversion sequence (indicated by BUSY going low), or as each
result becomes available (indicated by EOC going low). Data is
read from the part via a 12-bit parallel data bus with standard
CS and RD signals—see the
section.
Conversion time for each channel of the AD7864 is 1.65 μs, and
the track-and-hold acquisition time is 0.35 μs. To obtain optimum
performance from the part, the read operation should not occur
during a channel conversion or during the 100 ns prior to the
next CONVST rising edge. This allows the part to operate at
throughput rates up to 130 kHz for all four channels and
achieve data sheet specifications.
Track-and-Hold Amplifiers
The track-and-hold amplifiers on the AD7864 allow the ADCs
to accurately convert an input sine wave of full-scale amplitude
to 12-bit accuracy. The input bandwidth of the track-and-hold
is greater than the Nyquist rate of the ADC even when the ADC
is operated at its maximum throughput rate of 500 kSPS (that is,
the track-and-hold can handle input frequencies in excess of
250 kHz).
The track-and-hold amplifiers acquire input signals to 12-bit
accuracy in less than 350 ns. The operation of the track-and-
holds are essentially transparent to the user. The four track-and-
hold amplifiers sample their respective input channels simulta-
neously, on the rising edge of CONVST. The aperture time for
the track-and-holds (that is, the delay time between the external
CONVST signal and the track-and-hold actually going into hold)
is typically 15 ns and, more importantly, is well matched across
the four track-and-holds on one device as well as being well
matched from device to device. This allows the relative phase
information between different input channels to be accurately
preserved. It also allows multiple AD7864s to sample more than
four channels simultaneously. At the end of a conversion sequence,
the part returns to its tracking mode. The acquisition time of
the track-and-hold amplifiers begin at this point.
Reference
The AD7864 contains a single reference pin, labeled VREF. The
VREF pin provides access to the 2.5 V reference within the part,
or it serves as the reference source for the part by connecting
VREF to an external 2.5 V reference. The part is specified with a
2.5 V reference voltage. Errors in the reference source result in
gain errors in the transfer function of the AD7864 and adds to
the specified full-scale errors on the part. On the AD7864-1 and
AD7864-3, it also results in an offset error injected in the attenuator
The AD7864 contains an on-chip 2.5 V reference. To use this
reference as the reference source for the AD7864, simply con-
nect a 0.1 μF disk ceramic capacitor from the VREF pin to AGND.
The voltage that appears at this pin is internally buffered before
being applied to the ADC. If this reference is used externally to
the AD7864, it should be buffered because the part has a FET
switch in series with the reference output resulting in a 6 kΩ
相关PDF资料 |
PDF描述 |
|---|---|
| AD7865YSZ-3 | IC ADC 14BIT 4CHAN 5V 44-MQFP |
| AD7866ARU-REEL7 | IC ADC 12BIT 2CH DUAL 20TSSOP |
| AD7871KP | IC ADC 14BIT SAMPLING 28-PLCC |
| AD7873ARUZ | IC ADC 12BIT TOUCHSCREEN 16TSSOP |
| AD7875LNZ | IC ADC 12BIT SAMPLING 5V 24-DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7864BSZ-1REEL2 | 制造商:AD 制造商全称:Analog Devices 功能描述:4-Channel, Simultaneous Sampling, High Speed, 12-Bit ADC |
| AD7865 | 制造商:AD 制造商全称:Analog Devices 功能描述:Four-Channel, Simultaneous Sampling, Fast, 14-Bit ADC |
| AD7865AS-1 | 制造商:Rochester Electronics LLC 功能描述:4 CH. SIMULTANEOUS BIPOLAR,14-B ADC I.C. - Bulk 制造商:Analog Devices 功能描述:Analog-Digital Converter IC Number of Bi |
| AD7865AS-1REEL | 制造商:Analog Devices 功能描述:ADC Single SAR 350ksps 14-bit Parallel 44-Pin MQFP T/R 制造商:Rochester Electronics LLC 功能描述:4 CH. SIMULTANEOUS BIPOLAR,14-B ADC I.C. - Tape and Reel |
| AD7865AS2 | 制造商:AD 功能描述:* |
发布紧急采购，3分钟左右您将得到回复。