参数资料
| 型号： | AD7869JRZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 12/16页 |
| 文件大小： | 0K |
| 描述： | IC I/O PORT 14BIT ANLG 28SOIC |
| 标准包装： | 1 |
| 应用： | 模拟 I/O |
| 接口： | TTL/CMOS |
| 电源电压： | 4.75 V ~ 5.25 V |
| 封装/外壳： | 28-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 28-SOIC W |
| 包装： | 管件 |
| 安装类型： | 表面贴装 |
AD7869
–5–
AD7869 PIN FUNCTION DESCRIPTION
DIP Pin
Number
Mnemonic
Function
POWER SUPPLY
7 & 23
VDD
Positive Power Supply, 5 V
± 5%. Both VDD pins must be tied together.
10 & 22
VSS
Negative Power Supply, –5 V
± 5%. Both VSS pins must be tied together.
8 & 19
AGND
Analog Ground. Both AGND pins must be tied together.
6 & 17
DGND
Digital Ground. Both DGND pins must be tied together.
ANALOG SIGNAL AND REFERENCE
21
VIN
ADC Analog Input. The ADC input range is
±3 V.
9VOUT
Analog Output Voltage from DAC. This output comes from a buffer amplifier. The range is bipolar,
±3 V
with RI DAC = +3 V.
20
RO ADC
Voltage Reference Output. The internal ADC 3 V reference is provided at this pin. This output may be used as a
reference for the DAC by connecting it to the RI DAC input. The external load capability of this reference is 500
μA.
11
RO DAC
DAC Voltage Reference Output. This is one of two internal voltage references. To operate the DAC with this
internal reference, RO DAC should be connected to RI DAC. The external load capability of the reference is 500
μA.
12
RI DAC
DAC Voltage Reference Input. The voltage reference for the DAC must be applied to this pin. It is internally
buffered before being applied to the DAC. The nominal reference voltage for correct operation of the AD7869 is 3 V.
ADC INTERFACE AND CONTROL
2
CLK
Clock Input. An external TTL-compatible clock may be applied to this input. Alternatively, tying this pin to VSS
enables the internal laser-trimmed oscillator.
3
RFS
Receive Frame Synchronization, Logic Output. This is an active low open-drain output that provides a framing
pulse for serial data. An external 4.7 k
Ω pull-up resistor is required on RFS.
4
RCLK
Receive Clock, Logic Output. RCLK is the gated serial clock output that is derived from the internal or external
ADC clock. If the CONTROL input is at VSS, the clock runs continuously. With the CONTROL input at DGND,
the RCLK output is gated off (three-state) after serial transmission is complete. RCLK is an open-drain output and
requires an external 2 k
Ω pull-up resistor.
5
DR
Receive Data, Logic Output. This is an open-drain data output used in conjunction with
RFS and RCLK to transmit
data from the ADC. Serial data is valid on the falling edge of RCLK when
RFS is low. An external 4.7 kΩ resistor is
required on the DR output.
1
CONVST
Convert Start, Logic Input. A low to high transition on this input puts the track-and-hold amplifier into the hold
mode and starts an ADC conversion. This input is asynchronous to the CLK input.
24
CONTROL
Control, Logic Input. With this pin at 0 V, the RCLK is noncontinuous. With this pin at –5 V, the RCLK is contin-
uous. Note, tying this pin to VDD places the part in a factory test mode where normal operation is not exhibited.
DAC INTERFACE AND CONTROL
14
TFS
Transmit Frame Synchronization, Logic Input. This is a frame or synchronization signal for the DAC with serial
data expected after the falling edge of this signal.
15
DT
Transmit Data, Logic Input. This is the data input that is used in conjunction with
TFS and TCLK to transfer
serial data to the input latch.
16
TCLK
Transmit Clock, Logic Input. Serial data bits are latched on the falling edge of TCLK when
TFS is low.
13
LDAC
Load DAC, Logic Input. A new word is transferred into the DAC latch from the input latch on the falling edge
of this signal.
18
NC
No Connect.
REV. B
CONVST
1
CLK
2
RFS
3
RCLK
4
CONTROL
24
VDD
23
VSS
22
VIN
21
DR
5
DGND
6
VDD 7
RO ADC
20
AGND
19
NC
18
AGND
8
DGND
17
VOUT 9
TCLK
16
VSS 10
DT
15
RO DAC 11
TFS
14
RI DAC 12
LDAC
13
NC = NO CONNECT
AD7869
TOP VIEW
(Not to Scale)
AD7869
TOP VIEW
(Not to Scale)
CONVST
1
CLK
2
RFS
3
NC
4
RCLK
5
DR
6
DGND
7
VDD 8
AGND
9
VOUT 10
VSS 12
CONTROL
28
VDD
27
VSS
26
NC
25
VIN
24
RO ADC
23
AGND
22
DGND
21
TCLK
20
NC
19
NC 11
NC
18
RO DAC 13
TFS
16
RI DAC 14
LDAC
15
DT
17
NC = NO CONNECT
DIP
SOIC
PIN CONFIGURATIONS
相关PDF资料 |
PDF描述 |
|---|---|
| AD7874SE | IC DAS 12BIT 4CH 5V 28-CLCC |
| AD7890BRZ-4 | IC DAS 12BIT 8CH 24-SOIC |
| AD7891BPZ-2 | IC DAS 12BIT 8CH 44-PLCC |
| AD80066KRSZRL | IC DSP CTLR 16BIT 28SSOP |
| AD8016AREZ-REEL7 | IC LINE DRIVER ADSL 28TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7870 | 制造商:AD 制造商全称:Analog Devices 功能描述:LC2MOS Complete, 12-Bit, 100 kHz, Sampling ADCs |
| AD7870A | 制造商:AD 制造商全称:Analog Devices 功能描述:LC2MOS Complete, 12-Bit, 100 kHz , Sampling ADC |
| AD7870AJN | 制造商:Analog Devices 功能描述:ADC Single SAR 100ksps 12-bit Parallel/Serial 24-Pin PDIP 制造商:Rochester Electronics LLC 功能描述:12-BIT SAMPLING ADC IC - Bulk |
| AD7870AJNZ | 功能描述:IC ADC 12BIT SAMPLING 3V 24-DIP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:- 位数:14 采样率（每秒）:83k 数据接口:串行，并联 转换器数目:1 功率耗散（最大）:95mW 电压电源:双 ± 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:28-DIP（0.600"，15.24mm） 供应商设备封装:28-PDIP 包装:管件 输入数目和类型:1 个单端，双极 |
| AD7870AQ | 功能描述:IC ADC 12BIT SAMPLING 3V 24-CDIP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 位数:12 采样率（每秒）:3M 数据接口:- 转换器数目:- 功率耗散（最大）:- 电压电源:- 工作温度:- 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-23-6 包装:带卷 (TR) 输入数目和类型:- |
发布紧急采购，3分钟左右您将得到回复。