参数资料
| 型号： | AD7873BRQZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 14/29页 |
| 文件大小： | 0K |
| 描述： | IC ADC 12BIT TOUCHSCREEN 16QSOP |
| 标准包装： | 98 |
| 类型： | 电阻 |
| 触摸面板接口： | 4 线 |
| 输入数/键： | 1 TSC |
| 分辨率（位）： | 12 b |
| 评估套件： | 可供 |
| 数据接口： | 串行 |
| 数据速率/采样率 (SPS，BPS)： | 125k |
| 电压基准： | 外部，内部 |
| 电源电压： | 2.2 V ~ 5.25 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-QSOP |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页
AD7873
Data Sheet
Rev. F | Page 20 of 28
Table 8. Power Management Options
PD1
PD0
PENIRQ
Description
0
Enabled
This configuration results in immediate power-down of the on-chip reference as soon as PD1 is set to 0. The ADC
powers down only between conversions. When PD0 is set to 0, the conversion is performed first and the ADC
powers down upon completion of that conversion (or upon the rising edge of CS, if it occurs first). At the start of
the next conversion, the ADC instantly powers up to full power. This means if the device is being used in the
differential mode, or an external reference is used, there is no need for additional delays to ensure full operation
and the very first conversion is valid. The Y– switch is on while in power-down. When the device is performing
differential table conversions, the reference and reference buffer do not attempt to power up with Bit PD1 and
Bit PD0 programmed in this way.
0
1
Enabled
This configuration results in switching the reference off immediately and the ADC on permanently. When the
device is performing differential tablet conversions, the reference and reference buffer do not attempt to power
up with Bit PD1 and Bit PD0 programmed in this way.
1
0
Enabled
This configuration results in switching the reference on and powering the ADC down between conversions. The
ADC powers down only between conversions. When PD0 is set to 0, the conversion is performed first, and the
ADC powers down upon completion of the conversion (or upon the rising edge of CS if it occurs first). At the start
of the next conversion, the ADC instantly powers up to full power. There is no need for additional delays to ensure
full operation as the reference remains permanently powered up.
1
Disabled
This configuration results in always keeping the device powered up. The reference and the ADC are on.
POWER VS. THROUGHPUT RATE
By using the power-down options on the AD7873 when not
converting, the average power consumption of the device
decreases at lower throughput rates. Figure 35 shows how, as
the throughput rate is reduced while maintaining the DCLK
frequency at 2 MHz, the device remains in its power-down state
longer and the average current consumption over time drops
accordingly.
Figure 35. Supply Current vs. Throughput (A)
For example, if the AD7873 is operated in a 24-DCLK continuous
sampling mode, with a throughput rate of 10 kSPS and a DCLK
of 2 MHz, and the device is placed in the power-down mode
between conversions, (PD0, PD1 = 0, 0), that is, the ADC shuts
down between conversions but the reference remains powered
down permanently, then the current consumption is calculated
as follows. The current consumption during normal operation
with a 2 MHz DCLK is 210 A (VCC = 2.7 V). Assuming an
external reference is used, the power-up time of the ADC is
instantaneous, so when the part is converting, it consumes
210 A. In this mode of operation, the part powers up on the
fourth falling edge of DCLK after the start bit is recognized. It
goes back into power-down at the end of conversion on the
20th falling edge of DCLK, meaning that the part consumes
210 A for 16 DCLK cycles only, 8 s during each conversion
cycle. If the throughput rate is 10 kSPS, the cycle time is 100 s
and the average power dissipated during each cycle is
(8/100) × (210 A) = 16.8 A.
S
UP
P
L
Y
CURRE
NT
(
A)
1
100
10
1000
0
120
THROUGHPUT (kSPS)
40
60
0
20
80
100
fDCLK = 16 × fSAMPLE
fDCLK = 2MHz
VCC = 2.7V
TA = –40°C TO +85°C
02164-
035
相关PDF资料 |
PDF描述 |
|---|---|
| MS27473E14A35PA | CONN PLUG 37POS STRAIGHT W/PINS |
| MS27467T25F29SC | CONN PLUG 29POS STRAIGHT W/SCKT |
| MS3101R22-19S | CONN RCPT 14POS PANEL MNT W/SCKT |
| MS27499E24B35SC | CONN RCPT 128POS BOX MNT W/SCKT |
| MS27467T15F35SB | CONN PLUG 37POS STRAIGHT W/SCKT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7873BRQZ-REEL | 功能描述:IC ADC 12BIT TOUCHSCREEN 16QSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 触摸屏控制器 系列:- 标准包装:96 系列:- 类型:- 触摸面板接口:- 输入数/键:- 分辨率（位）:- 评估套件:* 数据接口:- 数据速率/采样率 (SPS，BPS):- 电压基准:- 电源电压:- 电流 - 电源:- 工作温度:- 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:带卷 (TR) |
| AD7873BRQZ-REEL7 | 功能描述:IC ADC 12BIT TOUCHSCREEN 16QSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 触摸屏控制器 系列:- 标准包装:96 系列:- 类型:- 触摸面板接口:- 输入数/键:- 分辨率（位）:- 评估套件:* 数据接口:- 数据速率/采样率 (SPS，BPS):- 电压基准:- 电源电压:- 电流 - 电源:- 工作温度:- 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:带卷 (TR) |
| AD7874 | 制造商:AD 制造商全称:Analog Devices 功能描述:LC2MOS 4-Channel, 12-Bit Simultaneous Sampling Data Acquisition System |
| AD7874AN | 功能描述:IC DAS 12BIT 4CH LC2MOS 28-DIP RoHS:否 类别:集成电路 (IC) >> 数据采集 - ADCs/DAC - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 类型:数据采集系统（DAS） 分辨率（位）:16 b 采样率（每秒）:21.94k 数据接口:MICROWIRE?，QSPI?，串行，SPI? 电压电源:模拟和数字 电源电压:1.8 V ~ 3.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（6x6） 包装:托盘 |
| AD7874ANZ | 功能描述:IC DAS 12BIT 4CH LC2MOS 28-DIP RoHS:是 类别:集成电路 (IC) >> 数据采集 - ADCs/DAC - 专用型 系列:- 产品培训模块:Data Converter Basics 标准包装:1 系列:- 类型:电机控制 分辨率（位）:12 b 采样率（每秒）:1M 数据接口:串行，并联 电压电源:单电源 电源电压:2.7 V ~ 3.6 V，4.5 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:100-TQFP 供应商设备封装:100-TQFP（14x14） 包装:剪切带 (CT) 其它名称:296-18373-1 |
发布紧急采购，3分钟左右您将得到回复。