参数资料
型号: AD7877ACBZ-REEL
厂商: Analog Devices Inc
文件页数: 19/45页
文件大小: 0K
描述: IC CTRLR TOUCH SCREEN 25-WLCSP
标准包装: 10,000
类型: 电阻
触摸面板接口: 4 线
输入数/键: 1 TSC
分辨率(位): 12 b
评估套件: 可供
数据接口: 串行,SPI?
数据速率/采样率 (SPS,BPS): 125k
电压基准: 外部,内部
电源电压: 2.7 V ~ 5.25 V
电流 - 电源: 1µA
工作温度: -40°C ~ 85°C
安装类型: 表面贴装
封装/外壳: 25-UFBGA,WLCSP
供应商设备封装: 25-WLCSP
包装: 带卷 (TR)
配用: EVAL-AD7877EBZ-ND - BOARD EVALUATION FOR AD7877
Data Sheet
AD7877
Rev. D | Page 25 of 44
If fDCLK = 20 MHz (maximum), then tDCLK = 50 ns.
t2 = 512 s with timer set to 1024 (TMR bits = 01b)
tWRITE = tREAD = 16 CLK period × tDCLK = 800 ns
t3 = maximum time taken to write read address and read
11 registers = 800 ns (write) + [800 ns (read) × 11] = 9.6 s.
t4MAX = t2 t3 = 512 s 9.6 s = 502.4 s
Pen Interrupt (PENIRQ)
The pen interrupt request output (PENIRQ) goes low whenever
the screen is touched. The pen interrupt equivalent output
circuitry is outlined in Figure 43. This is a digital logic output
with an internal pull-up resistor of 50 k, which means it does
not need an external pull-up. The PENIRQ output idles high.
The PENIRQ circuitry is always enabled, except during
conversions.
03796-021
X+
TOUCH
SCREEN
Y+
50k
Y–
X–
PENIRQ
ENABLE
PENIRQ
VCC
Figure 43. PENIRQ Output Equivalent Circuit
When the screen is touched, PENIRQ goes low. This generates
an interrupt request to the host. When the screen touch ends,
and if the ADC is idle, PENIRQ immediately goes high. If the
ADC is converting, PENIRQ goes high once the ADC becomes
idle. The PENIRQ operation for these two conditions is shown
03796-022
SCREEN
PENIRQ
ADC
STATUS
TOUCHED
NOT
TOUCHED
NOT
TOUCHED
NOT
TOUCHED
NOT
TOUCHED
ADC IDLE
SCREEN
PENIRQ
ADC
STATUS
TOUCHED
ADC IDLE
ADC
CONVERTING
ADC IDLE
RELEASE NOT
DETECTED
PENIRQ
DETECTS
RELEASE
PENIRQ
DETECTS
RELEASE
PENIRQ
DETECTS
TOUCH
PENIRQ
DETECTS
TOUCH
Figure 44. PENIRQ Operation for ADC Idle and ADC Converting
SYNCRONIZING THE AD7877 TO THE HOST CPU
The two suggested methods for synchronizing the AD7877
to its host CPU are slave mode, in which the mode bits can
be either 01b or 10b, and master mode, in which the mode
bits are 11b.
In slave mode, PENIRQ can be used as an interrupt to the host.
When PENIRQ goes low to indicate that the screen has been
touched, the host is awakened. The host can then program the
AD7877 to begin converting in either Mode 01b or Mode 10b,
and can read the result registers after the conversions are
completed.
In master mode, DAV can also be used as an interrupt to the
host. However, the host should first initialize the AD7877 in
Mode 11b. The host can then go into sleep mode to conserve
power. The wake-up on touch feature of the AD7877 is active in
this mode, therefore, when the screen is touched, the
programmed sequence of conversions begins automatically.
When the DAV signal asserts, the host reads the new data avail-
able in the AD7877 results registers and returns to sleep mode.
This method can significantly reduce the load on the host.
相关PDF资料
PDF描述
MS27497E24F35S CONN RCPT 128POS WALL MNT W/SCKT
MS3106R32-17PY CONN PLUG 4POS STRAIGHT W/PINS
VI-24D-IW-B1 CONVERTER MOD DC/DC 85V 100W
VI-24B-IW-B1 CONVERTER MOD DC/DC 95V 100W
VE-J54-MX-F1 CONVERTER MOD DC/DC 48V 75W
相关代理商/技术参数
参数描述
AD7877ACBZ-REEL7 功能描述:IC CTRLR TOUCH SCREEN 25-WLCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 触摸屏控制器 系列:- 标准包装:96 系列:- 类型:- 触摸面板接口:- 输入数/键:- 分辨率(位):- 评估套件:* 数据接口:- 数据速率/采样率 (SPS,BPS):- 电压基准:- 电源电压:- 电流 - 电源:- 工作温度:- 安装类型:表面贴装 封装/外壳:16-TSSOP(0.173",4.40mm 宽) 供应商设备封装:16-TSSOP 包装:带卷 (TR)
AD7877ACP 制造商:Analog Devices 功能描述:TOUCH SCREEN CNTRLR 32LFCSP - Bulk
AD7877ACP-500RL7 制造商:Analog Devices 功能描述:TOUCH SCREEN CONTROLLER
AD7877ACP-REEL 制造商:AD 制造商全称:Analog Devices 功能描述:Touch Screen Controller
AD7877ACP-REEL7 制造商:Analog Devices 功能描述:TOUCH SCREEN CONTROLLER