- 您现在的位置：买卖IC网 > PDF目录9712 > AD7877ACBZ-REEL (Analog Devices Inc)IC CTRLR TOUCH SCREEN 25-WLCSP PDF资料下载
参数资料
| 型号： | AD7877ACBZ-REEL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 20/45页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR TOUCH SCREEN 25-WLCSP |
| 标准包装： | 10,000 |
| 类型： | 电阻 |
| 触摸面板接口： | 4 线 |
| 输入数/键： | 1 TSC |
| 分辨率（位）： | 12 b |
| 评估套件： | 可供 |
| 数据接口： | 串行，SPI? |
| 数据速率/采样率 (SPS，BPS)： | 125k |
| 电压基准： | 外部，内部 |
| 电源电压： | 2.7 V ~ 5.25 V |
| 电流 - 电源： | 1µA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 25-UFBGA，WLCSP |
| 供应商设备封装： | 25-WLCSP |
| 包装： | 带卷 (TR) |
| 配用： | EVAL-AD7877EBZ-ND - BOARD EVALUATION FOR AD7877 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页当前第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页
AD7877
Data Sheet
Rev. D | Page 26 of 44
8-BIT DAC
The AD7877 features an on-chip 8-bit DAC for LCD contrast
control. The DAC can be configured for voltage output by
clearing Bit 2 of the DAC register (Address 1110b), or for
current output by setting this bit.
The output voltage range can be set to 0 to VCC/2 by clearing
Bit 0 of the DAC register, or to 0 to VCC by setting this bit. In
current mode, the output range is selectable by an external
resistor, RRNG, connected between the ARNG pin and GND.
This sets the full-scale output current according to the following
equations:
IFS = VCC/(RRNG × 6)
therefore,
RRNG = VCC/(IFS × 6)
(5)
In current mode, the DAC sinks current, that is, positive
current flows into ground. The maximum output current is
1000 A. The DAC is updated by writing to Address 1110b of
the DAC register. The 8 MSBs of the data-word are used for
DAC data.
The most effective way to control LCD contrast with the DAC is
to use it to control the feedback loop of the dc-to-dc converter
that supplies the LCD bias voltage, as shown in Figure 45. The
bias voltage for graphic LCDs is typically in the range of 20 V to
25 V, and the dc-to-dc converter usually has a feedback loop
that attenuates the output voltage and compares it with an
internal reference voltage.
03796-
023
DC-DC
CONVERTER
VFB
VOUT
TO LCD
8-BIT
DAC
AD7877
ARNG
RRNG1
GND
NOTES:
1RRNG IS REQUIRED ONLY IF DAC IS IN CURRENT MODE.
2R1 IS REQUIRED ONLY IF DAC IS IN VOLTAGE MODE.
AOUT
R12
IOUT
R3
R2
COMP
VREF
Figure 45. Using the DAC to Adjust LCD Contrast
The circuit operates as follows. If the DAC is in current mode
when the DAC output is zero, it has no effect on the feedback
loop. Regardless of what the DAC does, the feedback loop
maintains the voltage across R4, VFB, equal to VREF, and the
output voltage, VOUT, is
VREF × (R2 + R3)/R3
As the DAC output is increased, it increases the feedback current,
so the voltage across R2 and, therefore, the output voltage also
increase. Note that the voltage across R3 does not change. This
is important for calculation of the adjustment range.
In current mode, it is quite easy to calculate the resistor values
to give the required adjustment range in VOUT using the
following steps:
1. Find the required maximum and minimum values of VOUT
from the LCD manufacturer’s data
2. Decide on the current around the feedback loop. For
reasonable accuracy of the output voltage, this current
should be at least 100 times the input bias current of the
dc-to-dc converter’s comparator
3. Calculate R3 using the following equation:
R3 = VFB/IFB = VREF/IFB
4. Calculate R2 for the minimum value of VOUT, when the
DAC has no effect
R2 = R3(VOUT(MIN) VREF)/VREF
5. Because the voltage across R3 does not change, subtract
VREF from VOUTMAX and VOUTMIN to get the maximum and
minimum voltages across R2
6. Calculate the change in feedback current between
minimum and maximum output voltages
I = VR2(MAX)/R2 VR2(MIN)/R2
This is the required full-scale current of the DAC.
7. Calculate RRNG from Equation 5
Example:
1. VCC = 5 V
VOUT(MIN) is 20 V and VOUT(MAX) is 25 V
VREF is 1.25 V
2. Allow 100 A around the feedback loop.
3. R3 = 1.25 V/100 A = 12.5 k
Use the nearest preferred value of 12 k and recalculate
the feedback current as
IFB = 1.25 V/12 k = 104 A
4. R2 = (20 V 1.25 V)/104 A = 180 k
5. I = 23.75 V/180 k 18.75 V/180 k = 28 A
6. RRNG = 5 V/(6 × 28 A) = 30 k
In voltage mode, the circuit operation depends on whether the
maximum output voltage of the DAC exceeds the dc to dc
converter VREF.
相关PDF资料 |
PDF描述 |
|---|---|
| MS27497E24F35S | CONN RCPT 128POS WALL MNT W/SCKT |
| MS3106R32-17PY | CONN PLUG 4POS STRAIGHT W/PINS |
| VI-24D-IW-B1 | CONVERTER MOD DC/DC 85V 100W |
| VI-24B-IW-B1 | CONVERTER MOD DC/DC 95V 100W |
| VE-J54-MX-F1 | CONVERTER MOD DC/DC 48V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7877ACBZ-REEL7 | 功能描述:IC CTRLR TOUCH SCREEN 25-WLCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 触摸屏控制器 系列:- 标准包装:96 系列:- 类型:- 触摸面板接口:- 输入数/键:- 分辨率（位）:- 评估套件:* 数据接口:- 数据速率/采样率 (SPS，BPS):- 电压基准:- 电源电压:- 电流 - 电源:- 工作温度:- 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:带卷 (TR) |
| AD7877ACP | 制造商:Analog Devices 功能描述:TOUCH SCREEN CNTRLR 32LFCSP - Bulk |
| AD7877ACP-500RL7 | 制造商:Analog Devices 功能描述:TOUCH SCREEN CONTROLLER |
| AD7877ACP-REEL | 制造商:AD 制造商全称:Analog Devices 功能描述:Touch Screen Controller |
| AD7877ACP-REEL7 | 制造商:Analog Devices 功能描述:TOUCH SCREEN CONTROLLER |
发布紧急采购，3分钟左右您将得到回复。