- 您现在的位置：买卖IC网 > PDF目录10356 > AD7920AKSZ-REEL7 (Analog Devices Inc)IC ADC 12BIT SRL 250KSPS SC70-6 PDF资料下载
参数资料
| 型号： | AD7920AKSZ-REEL7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 4/24页 |
| 文件大小： | 0K |
| 描述： | IC ADC 12BIT SRL 250KSPS SC70-6 |
| 标准包装： | 3,000 |
| 位数： | 12 |
| 采样率（每秒）： | 250k |
| 数据接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 15mW |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 6-TSSOP，SC-88，SOT-363 |
| 供应商设备封装： | SC-70-6 |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 1 个单端，单极 |
| 配用： | EVAL-AD7920CBZ-ND - BOARD EVALUATION FOR AD7920 |
AD7910/AD7920
Rev. C | Page 12 of 24
TERMINOLOGY
Integral Nonlinearity
The maximum deviation from a straight line passing through
the endpoints of the ADC transfer function. For the AD7920
and AD7910, the endpoints of the transfer function are zero
scale, a point 1 LSB below the first code transition, and full
scale, a point 1 LSB above the last code transition.
Differential Nonlinearity
The difference between the measured and the ideal 1 LSB
change between any two adjacent codes in the ADC.
Offset Error
The deviation of the first code transition (00 . . . 000) to (00 . . . 001)
from the ideal, that is, GND + 1 LSB.
Gain Error
The deviation of the last code transition (111 . . . 110) to
(111 . . . 111) from the ideal, that is, VREF 1 LSB after the offset
error has been adjusted out.
Track-and-Hold Acquisition Time
The track-and-hold amplifier returns to track mode at the end
of conversion. Track-and-hold acquisition time is the time
required for the output of the track-and-hold amplifier to reach
its final value, within ±0.5 LSB, after the end of conversion. See
the Serial Interface section for more details.
Signal-to-(Noise + Distortion) Ratio
The measured ratio of signal-to-(noise + distortion) at the output
of the A/D converter. The signal is the rms amplitude of the
fundamental. Noise is the sum of all nonfundamental signals up
to half the sampling frequency (fS/2), excluding dc. The ratio is
dependent on the number of quantization levels in the digiti-
zation process. The more levels, the smaller the quantization
noise. The theoretical signal-to-(noise + distortion) ratio for an
ideal N-bit converter with a sine wave input is given by:
Signal-to-(Noise + Distortion) = (6.02N + 1.76) dB
Thus, for a 12-bit converter this is 74 dB, and for a 10-bit
converter this is 62 dB.
Total Unadjusted Error
A comprehensive specification that includes gain error, linearity
error, and offset error.
Total Harmonic Distortion (THD)
Total harmonic distortion is the ratio of the rms sum of
harmonics to the fundamental. It is defined as:
1
2
6
2
5
2
4
2
3
2
log
20
)
(
V
dB
THD
+
=
where:
V1 is the rms amplitude of the fundamental.
V2, V3, V4, V5, and V6 are the rms amplitudes of the second
through the sixth harmonics.
Peak Harmonic or Spurious Noise
Peak harmonic or spurious noise is the ratio of the rms value of
the next largest component in the ADC output spectrum (up to
fS/2 and excluding dc) to the rms value of the fundamental.
Normally, the value of this specification is determined by the
largest harmonic in the spectrum, but for ADCs whose
harmonics are buried in the noise floor, it is a noise peak.
Intermodulation Distortion
With inputs consisting of sine waves at two frequencies, fa and fb,
any active device with nonlinearities creates distortion products
at sum and difference frequencies of mfa ± nfb where m, n = 0, 1,
2, 3, and so on. Intermodulation distortion terms are those for
which neither m nor n are equal to zero. For example, the second-
order terms include (fa + fb) and (fa fb), while the third-order
terms include (2fa + fb), (2fa fb), (fa + 2fb), and (fa 2fb).
The AD7910/AD7920 are tested using the CCIF standard, where
two input frequencies are used (see fa and fb in the Specifications
page). In this case, the second-order terms are usually distanced in
frequency from the original sine waves, while the third-order terms
are usually at a frequency close to the input frequencies. As a result,
the second- and third-order terms are specified separately. The
calculation of the intermodulation distortion is as per the THD
specification, the ratio of the rms sum of the individual distortion
products to the rms amplitude of the sum of the fundamentals,
expressed in dB.
相关PDF资料 |
PDF描述 |
|---|---|
| VE-J5P-MX | CONVERTER MOD DC/DC 13.8V 75W |
| VI-BNR-IV-F4 | CONVERTER MOD DC/DC 7.5V 150W |
| D38999/26WB5SNLC | CONN HSG PLUG 5POS STRGHT SCKT |
| MS3106A20-25P | CONN PLUG 13POS STRAIGHT W/PINS |
| D38999/20WC4PNLC | CONN HSG RCPT 4POS WALL MT PINS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7920BKS | 制造商:AD 制造商全称:Analog Devices 功能描述:250 kSPS, 10-/12-Bit ADCs in 6-Lead SC70 |
| AD7920BKS-500RL7 | 制造商:Analog Devices 功能描述:ADC Single SAR 250ksps 12-bit Serial 6-Pin SC-70 T/R 制造商:Rochester Electronics LLC 功能描述:12-BIT 250KSPS,ADC SC70 PKG I.C. - Bulk |
| AD7920BKS-REEL | 制造商:AD 制造商全称:Analog Devices 功能描述:250 kSPS, 10-/12-Bit ADCs in 6-Lead SC70 |
| AD7920BKS-REEL7 | 制造商:Analog Devices 功能描述:ADC Single SAR 250ksps 12-bit Serial 6-Pin SC-70 T/R |
| AD7920BKSZ-500RL7 | 功能描述:IC ADC 12BIT SRL 250KSPS SC70-6 RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:microPOWER™ 位数:8 采样率（每秒）:1M 数据接口:串行，SPI? 转换器数目:1 功率耗散（最大）:- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘（4x4） 包装:Digi-Reel® 输入数目和类型:8 个单端，单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6 |
发布紧急采购，3分钟左右您将得到回复。