- 您现在的位置：买卖IC网 > PDF目录10695 > AD7921ARMZ-REEL7 (Analog Devices Inc)IC ADC 12BIT DUAL LP 8MSOP PDF资料下载
参数资料
| 型号： | AD7921ARMZ-REEL7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 10/28页 |
| 文件大小： | 0K |
| 描述： | IC ADC 12BIT DUAL LP 8MSOP |
| 标准包装： | 1,000 |
| 位数： | 12 |
| 采样率（每秒）： | 250k |
| 数据接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 20mW |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-MSOP |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 2 个单端，单极 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
AD7911/AD7921
Rev. A | Page 18 of 28
MODES OF OPERATION
The two modes of operation of the AD7911/AD7921 are
normal mode and power-down mode. The mode of operation is
selected by controlling the logic state of the CS signal. The point
at which CS is pulled high after the conversion has been initi-
ated determines whether the AD7911/AD7921 enter power-
down mode. Similarly, if already in power-down mode, CS can
control whether the device returns to normal operation or
remains in power-down mode.
Power-down mode is designed to provide flexible power
management options and to optimize the ratio of power
dissipation to throughput rate for different application
requirements.
NORMAL MODE
Normal mode is intended for the fastest throughput rate
performance. The user does not have to worry about any
power-up time, because the AD7911/AD7921 remain fully
powered all the time. Figure 26 shows the operation of the
AD7911/AD7921 in this mode.
The conversion is initiated on the falling edge of CS, as
described in the
section. To ensure that the part
remains fully powered up at all times,
CS must remain low until
at least 10 SCLK falling edges have elapsed after the falling edge
of CS. If CS is brought high any time after the 10th SCLK falling
edge but before the end of tCONVERT, the part remains powered-
up, but the conversion is terminated and DOUT goes back into
three-state. For the AD7911/AD7921, a minimum of 14 and
16 serial clock cycles, respectively, are needed to complete the
conversion and access the complete conversion result.
CS can idle high until the next conversion or can idle low until
CS returns high sometime prior to the next conversion
(effectively idling CS low). Once a data transfer is complete
(DOUT has returned to three-state), another conversion can be
initiated after the quiet time, tQUIET, has elapsed by bringing CS
low again.
POWER-DOWN MODE
Power-down mode is intended for use in applications where
slower throughput rates are required. Either the ADC is
powered down between each conversion, or a series of
conversions can be performed at a high throughput rate and
then the ADC is powered down for a relatively long duration
between these bursts of several conversions. When the
AD7911/AD7921 are in power-down mode, all analog circuitry
is powered down.
To enter power-down mode, the conversion process must be
interrupted by bringing CS high any time after the second
falling edge of SCLK and before the 10th falling edge of SCLK,
as shown in
. Once
CS has been brought high in this
window of SCLKs, then the part enters power-down mode, the
conversion that was initiated by the falling edge of CS is
terminated, and DOUT goes back into three-state. If CS is
brought high before the second SCLK falling edge, then the part
remains in normal mode and does not power down. This helps
to avoid accidental power-down due to glitches on the CS line.
To exit this mode of operation and power the AD7911/AD7921
up again, a dummy conversion is performed. On the falling
edge of CS, the device begins to power up and continues to
power up as long as CS is held low until after the falling edge of
the 10th SCLK. The device is fully powered up once 16 SCLKs
have elapsed and valid data results from the next conversion, as
shown in
. If
CS is brought high before the 10th falling
edge of SCLK, then the AD7911/AD7921 go back into power-
down mode. This helps to avoid accidental power-up due to
glitches on the CS line or an inadvertent burst of 8 SCLK cycles
while CS is low. Therefore, although the device might begin to
power up on the falling edge of CS, it powers down again on the
rising edge of CS, as long as this occurs before the 10th SCLK
falling edge.
04350-0-025
CS
1
10
12
14
16
1
10
12
14
16
AD7911/AD7921
SCLK
DIN
DOUT
CHANNEL FOR NEXT CONVERSION
CONVERSION RESULT
Figure 26. Normal Mode Operation
相关PDF资料 |
PDF描述 |
|---|---|
| AD7921ARM-REEL7 | IC ADC 12BIT DUAL LP 8-MSOP |
| VI-2TR-IX-B1 | CONVERTER MOD DC/DC 7.5V 75W |
| LT6700IS6-2#TR | IC COMP DUAL 400MV REF TSOT23-6 |
| VI-2TM-IX-B1 | CONVERTER MOD DC/DC 10V 75W |
| LT6700IS6-1#TRPBF | IC COMP DUAL 400MV REF TSOT23-6 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7921AUJ-R2 | 制造商:Analog Devices 功能描述: 制造商:Rochester Electronics LLC 功能描述:DUAL 12-BIT , 250KSPS ADC I.C. - Bulk |
| AD7921AUJ-REEL7 | 制造商:Analog Devices 功能描述:ADC Single SAR 250ksps 12-bit Serial 8-Pin TSOT T/R |
| AD7921AUJZ-R2 | 功能描述:IC ADC 12BIT DUAL LP TSOT-23-8 RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:2,500 系列:- 位数:16 采样率（每秒）:15 数据接口:MICROWIRE?，串行，SPI? 转换器数目:1 功率耗散（最大）:480µW 电压电源:单电源 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:38-WFQFN 裸露焊盘 供应商设备封装:38-QFN（5x7） 包装:带卷 (TR) 输入数目和类型:16 个单端，双极；8 个差分，双极 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| AD7921AUJZ-REEL7 | 功能描述:IC ADC 12BIT DUAL LP TSOT-23-8 RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:2,500 系列:- 位数:16 采样率（每秒）:15 数据接口:MICROWIRE?，串行，SPI? 转换器数目:1 功率耗散（最大）:480µW 电压电源:单电源 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:38-WFQFN 裸露焊盘 供应商设备封装:38-QFN（5x7） 包装:带卷 (TR) 输入数目和类型:16 个单端，双极；8 个差分，双极 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| AD7922 | 制造商:AD 制造商全称:Analog Devices 功能描述:2-Channel, 2.35 V to 5.25 V, 1 MSPS, 10-/12-Bit ADCs |
发布紧急采购，3分钟左右您将得到回复。