- 您现在的位置：买卖IC网 > PDF目录10310 > AD7922ARMZ-REEL (Analog Devices Inc)IC ADC DUAL 12BIT 2CH 8MSOP PDF资料下载
参数资料
| 型号： | AD7922ARMZ-REEL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 3/32页 |
| 文件大小： | 0K |
| 描述： | IC ADC DUAL 12BIT 2CH 8MSOP |
| 标准包装： | 3,000 |
| 位数： | 12 |
| 采样率（每秒）： | 1M |
| 数据接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 20mW |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-MSOP |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 2 个单端，单极 |
| 配用： | EVAL-AD7922CBZ-ND - BOARD EVAL FOR AD7922 |
第1页第2页当前第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
AD7912/AD7922
Rev. 0 | Page 11 of 32
TERMINOLOGY
Integral Nonlinearity
The maximum deviation from a straight line passing through
the endpoints of the ADC transfer function. For the AD7912/
AD7922, the endpoints of the transfer function are zero scale, a
point 1 LSB below the first code transition, and full scale, a
point 1 LSB above the last code transition.
Differential Nonlinearity
The difference between the measured and the ideal 1 LSB
change between any two adjacent codes in the ADC.
Offset Error
The deviation of the first code transition (00…000) to
(00… 001) from the ideal, that is, AGND + 1 LSB.
Offset Error Match
The difference in offset error between any two channels.
Gain Error
The deviation of the last code transition (111…110) to
(111…111) from the ideal, that is, VDD 1 LSB after the offset
error has been adjusted out.
Gain Error Match
The difference in gain error between any two channels.
Total Unadjusted Error
A comprehensive specification that includes gain error, linearity
error, and offset error.
Channel-to-Channel Isolation
A measure of the level of crosstalk between channels. It is
measured by applying a full-scale sine wave signal of 20 kHz to
500 kHz to the nonselected input channel and determining how
much that signal is attenuated in the selected channel with a
10 kHz signal. The figure is given worst case across both
channels for the AD7912/AD7922.
Track-and-Hold Acquisition Time
The time required for the output of the track-and-hold
amplifier to reach its final value within ±1 LSB after the end of
conversion. The track-and-hold amplifier returns to track mode
at the end of conversion. See the Serial Interface section for
more details.
Signal-to-Noise + Distortion Ratio (SINAD)
The measured ratio of signal-to-noise and distortion at the
output of the A/D converter. The signal is the rms value of the
sine wave, and noise is the rms sum of all nonfundamental
signals up to half the sampling frequency (fs/2), including
harmonics but excluding dc.
Signal-to-Noise Ratio (SNR)
The measured ratio of signal to noise at the output to the A/D
converter. The signal is the rms value of the sine wave input.
Noise is the rms quantization error within the Nyquist
bandwidth (fs/2). The rms value of a sine wave is one-half its
peak-to-peak value divided by √2, and the rms value for the
quantization noise is q/√12. The ratio is dependent on the
number of quantization levels in the digitization process; the
more levels, the smaller the quantization noise. For an ideal
N-bit converter, the SNR is defined as
dB
76
1
02
6
.
N
.
SNR
+
=
Therefore, for a 12-bit converter, SNR is 74 dB; for a 10-bit
converter, SNR is 62 dB.
However, various error sources in the ADC cause the measured
SNR to be less than the theoretical value. These errors occur due
to integral and differential nonlinearities, internal ac noise
sources, and so on.
Total Harmonic Distortion (THD)
The ratio of the rms sum of harmonics to the fundamental,
which is defined as
1
2
6
2
5
2
4
2
V
THD
+
=
3
log
20
)
dB
(
where:
V1 is the rms amplitude of the fundamental.
V2, V3, V4, V5, and V6 are the rms amplitudes of the second
through the sixth harmonics.
Peak Harmonic or Spurious Noise
The ratio of the rms value of the next largest component in the
ADC output spectrum (up to fs /2 and excluding dc) to the rms
value of the fundamental. Normally, the value of this specifica-
tion is determined by the largest harmonic in the spectrum, but
for ADCs where the harmonics are buried in the noise floor, it is
a noise peak.
相关PDF资料 |
PDF描述 |
|---|---|
| D38999/20WE6PNLC | CONN HSG RCPT 6POS WALL MT PINS |
| MS27473T14B35SA | CONN PLUG 37POS STRAIGHT W/SCKT |
| D38999/20WJ11SNLC | CONN HSG RCPT 11POS WALL MT SCKT |
| MS27484T16A26P | CONN PLUG 26POS STRAIGHT W/PINS |
| MS27466T17B55P | CONN RCPT 55POS WALL MT W/PINS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7922ARMZ-REEL7 | 功能描述:IC ADC DUAL 12BIT 2CH 8MSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| AD7922AUJ-R2 | 制造商:Rochester Electronics LLC 功能描述:DUAL 12-BIT, 1MSPS, ADC I.C - Bulk |
| AD7922AUJ-REEL | 制造商:Analog Devices 功能描述:ADC Single SAR 1Msps 12-bit Serial 8-Pin TSOT T/R |
| AD7922AUJ-REEL7 | 制造商:Analog Devices 功能描述:ADC Single SAR 1Msps 12-bit Serial 8-Pin TSOT T/R 制造商:Rochester Electronics LLC 功能描述:DUAL 12-BIT, 1MSPS, ADC I.C - Tape and Reel |
| AD7922AUJZ-REEL7 | 功能描述:IC ADC DUAL 12BIT 2CH TSOT-23-8 RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 其它有关文件:TSA1204 View All Specifications 标准包装:1 系列:- 位数:12 采样率（每秒）:20M 数据接口:并联 转换器数目:2 功率耗散（最大）:155mW 电压电源:模拟和数字 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-TQFP 供应商设备封装:48-TQFP（7x7） 包装:Digi-Reel® 输入数目和类型:4 个单端，单极；2 个差分，单极 产品目录页面:1156 (CN2011-ZH PDF) 其它名称:497-5435-6 |
发布紧急采购，3分钟左右您将得到回复。