- 您现在的位置：买卖IC网 > PDF目录10253 > AD7934BRUZ-6 (Analog Devices Inc)IC ADC 12BIT 4CH 625KSPS 28TSSOP PDF资料下载
参数资料
| 型号： | AD7934BRUZ-6 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 21/32页 |
| 文件大小： | 0K |
| 描述： | IC ADC 12BIT 4CH 625KSPS 28TSSOP |
| 标准包装： | 50 |
| 位数： | 12 |
| 采样率（每秒）： | 625k |
| 数据接口： | 并联 |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 13.5mW |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 28-TSSOP |
| 包装： | 管件 |
| 输入数目和类型： | 4 个单端，单极；2 个差分，单极；2 个伪差分，单极 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页当前第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
AD7933/AD7934
Rev. B | Page 28 of 32
AD7933/AD7934 to ADSP-21065L Interface
Figure 42 shows a typical interface between the AD7933/AD7934
and the ADSP-21065L SHARC processor. This interface is an
example of one of three DMA handshake modes. The MSX
control line is actually three memory select lines. Internal
ADDR25 to 24 are decoded into MS3 to 0, these lines are then
asserted as chip selects. The DMAR1 (DMA Request 1) is used
in this setup as the interrupt to signal the end of the conversion.
The rest of the interface is standard handshaking operation.
AD7933/
AD7934*
ADSP-21065L*
WR
DB0 TO DB11
D0 TO D31
ADDR0 TO ADDR23
MSX
DMAR1
BUSY
CS
CONVST
DSP/USER SYSTEM
WR
RD
*ADDITIONAL PINS OMITTED FOR CLARITY.
ADDRESS BUS
DATA BUS
ADDRESS
LATCH
ADDRESS
DECODER
03
71
3-
0
45
Figure 42. Interfacing to the ADSP-21065L
AD7933/AD7934 to TMS32020, TMS320C25, and
TMS320C5x Interface
Parallel interfaces between the AD7933/AD7934 and the
TMS32020, TMS320C25 and TMS320C5x family of DSPs are
shown in Figure 43. Select the memory-mapped address for the
AD7933/AD7934 to fall in the I/O memory space of the DSPs.
The parallel interface on the AD7933/AD7934 is fast enough to
interface to the TMS32020 with no extra wait states. If high
speed glue logic, such as 74AS devices, is used to drive the
RD and the WR lines when interfacing to the TMS320C25, no
wait states are necessary. However, if slower logic is used, data
accesses may be slowed sufficiently when reading from, and
writing to, the part to require the insertion of one wait state.
Extra wait states are necessary when using the TMS320C5x at
their fastest clock speeds (see the TMS320C5x User’s Guide
for details).
Data is read from the ADC using the following instruction:
IN D, ADC
where:
D is the data memory address.
ADC is the AD7933/AD7934 address.
AD7933/
AD7934*
TMS32020/
TMS320C25/
TMS320C50*
WR
RD
DB11 TO DB0
DMD0 TO DMD15
A0 TO A15
IS
READY
INTX
BUSY
CS
EN
CONVST
DSP/USER SYSTEM
TMS320C25
ONLY
R/W
STRB
*ADDITIONAL PINS OMITTED FOR CLARITY.
ADDRESS BUS
DATA BUS
ADDRESS
DECODER
03
71
3-
0
46
MSC
Figure 43. Interfacing to TMS32020/TMS320C25/TMS320C5x
AD7933/AD7934 to 80C186 Interface
Figure 44 shows the AD7933/AD7934 interfaced to the 80C186
microprocessor. The 80C186 DMA controller provides two
independent, high speed DMA channels where data transfers
can occur between memory and I/O spaces. Each data transfer
consumes two bus cycles, one cycle to fetch data and the other
to store data. After the AD7933/AD7934 finish a conversion,
the BUSY line generates a DMA request to Channel 1 (DRQ1).
Because of the interrupt, the processor performs a DMA read
operation, which also resets the interrupt latch. Sufficient
priority must be assigned to the DMA channel to ensure that
the DMA request is serviced before the completion of the next
conversion.
AD7933/
AD7934*
80C186*
WR
DB0 TO DB11
AD0 TO AD15
A16 TO A19
ALE
DRQ1
BUSY
CS
QR
S
CONVST
MICROPROCESSOR/
USER SYSTEM
WR
RD
*ADDITIONAL PINS OMITTED FOR CLARITY.
ADDRESS/DATA BUS
ADDRESS BUS
DATA BUS
ADDRESS
LATCH
ADDRESS
DECODER
03
71
3-04
7
Figure 44. Interfacing to the 80C186
相关PDF资料 |
PDF描述 |
|---|---|
| MS27505E9B44P | CONN RCPT 4POS BOX MNT W/PINS |
| MS27467E9F98P | CONN PLUG 3POS STRAIGHT W/PINS |
| MS3106F22-1S | CONN PLUG 2POS STRAIGHT W/SCKT |
| MS27513E18B32PA | CONN RCPT 32POS BOX MNT W/PINS |
| MS27468T11F35SD | CONN RCPT 13POS JAM NUT W/SCKT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7934BRUZ-6REEL7 | 功能描述:IC ADC 12BIT 4CH 625KSPS 28TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| AD7934BRUZ-REEL7 | 功能描述:IC ADC 12BIT 4CH 1.5MSPS 28TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| AD7937 | 制造商:AD 制造商全称:Analog Devices 功能描述:LC2MOS 8+4 Loading Dual 12-Bit DAC |
| AD7937AR | 功能描述:IC DAC 12BIT DUAL 8+4 24-SOIC RoHS:否 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 标准包装:2,400 系列:- 设置时间:- 位数:18 数据接口:串行 转换器数目:3 电压电源:模拟和数字 功率耗散（最大）:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:36-TFBGA 供应商设备封装:36-TFBGA 包装:带卷 (TR) 输出数目和类型:* 采样率（每秒）:* |
| AD7937AR-REEL | 功能描述:IC DAC 12BIT DUAL 8+4 24-SOIC RoHS:否 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 标准包装:2,400 系列:- 设置时间:- 位数:18 数据接口:串行 转换器数目:3 电压电源:模拟和数字 功率耗散（最大）:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:36-TFBGA 供应商设备封装:36-TFBGA 包装:带卷 (TR) 输出数目和类型:* 采样率（每秒）:* |
发布紧急采购，3分钟左右您将得到回复。