- 您现在的位置：买卖IC网 > PDF目录10304 > AD7942BCPZRL (Analog Devices Inc)IC ADC 14BIT SAR 250KSPS 10LFCSP PDF资料下载
参数资料
| 型号： | AD7942BCPZRL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 8/24页 |
| 文件大小： | 0K |
| 描述： | IC ADC 14BIT SAR 250KSPS 10LFCSP |
| 标准包装： | 5,000 |
| 系列： | PulSAR® |
| 位数： | 14 |
| 采样率（每秒）： | 250k |
| 数据接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 1.25mW |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-WFDFN 裸露焊盘，CSP |
| 供应商设备封装： | 10-LFCSP-WD（3x3） |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 1 个伪差分，单极 |
| 配用： | EVAL-AD7942CB-ND - BOARD EVALUATION FOR AD7942 |
AD7942
Rev. B | Page 16 of
24
Power Supply
The AD7942 is specified over a wide operating range from
2.3 V to 5.5 V. It has, unlike other low voltage converters, a
noise low enough to design a low supply (2.5 V) 14-bit resolu-
tion system with respectable performance. It uses two power
supply pins: a core supply, VDD, and a digital input/output
interface supply, VIO. VIO allows direct interface with any
logic between 1.8 V and VDD. To reduce the supplies needed,
the VIO and VDD can be tied together. The AD7942 is indepen-
dent of power supply sequencing between VIO and VDD.
Additionally, it is insensitive to power supply variations over
a wide frequency range, as shown in Figure 27.
55
60
65
70
75
80
85
90
P
S
R
(
d
B)
FREQUENCY (kHz)
10
1000
100
10000
04
65
7-
0
27
VDD = 5V
Figure 27. PSRR vs. Frequency
The AD7942 powers down automatically at the end of each
conversion phase and, therefore, the power scales linearly with
the sampling rate, as shown in Figure 28. This makes the part
ideal for low sampling rates (even rates of a few hertz) and low
battery-powered applications.
VDD = 5V
VDD = 2.5V
VIO
0
1000
10
0.1
0.001
O
PER
A
T
ING
CURR
E
NT
(
A)
10
100
1000
10000
100000
1000000
SAMPLING RATE (SPS)
04
65
7-
02
8
Figure 28. Operating Current vs. Sampling Rate
Supplying the ADC from the Reference
For simplified applications, the AD7942, with its low operating
current, can be supplied directly using the reference circuit, as
shown in Figure 29. The reference line can be driven by either
The system power supply directly,
A reference voltage with enough current output capability,
such as the ADR43x, or
A reference buffer, such as the AD8031, that can also filter
the system power supply (see Figure 29).
AD8031
AD7942
VIO
REF
VDD
10F
10
10k
5V
(NOTE 1)
1F
04
65
7-
0
29
NOTE 1: OPTIONAL REFERENCE BUFFER AND FILTER.
1F
Figure 29. Example of Application Circuit
DIGITAL INTERFACE
Although the AD7942 has a reduced number of pins, it offers
flexibility in its serial interface modes.
When in CS mode, the AD7942 is compatible with SPI, QSPI,
digital hosts, and DSPs (for example, Blackfin ADSP-BF53x or
ADSP-219x). A 3-wire interface using the CNV, SCK, and SDO
signals minimizes wiring connections, which is useful, for
instance, in isolated applications. A 4-wire interface using the
SDI, CNV, SCK, and SDO signals allows CNV, which initiates
conversions, to be independent of the readback timing (SDI).
This is useful in low jitter sampling or simultaneous sampling
applications.
When in chain mode, the AD7942 provides a daisy-chain
feature using the SDI input for cascading multiple ADCs on
a single data line similar to a shift register.
The mode in which the part operates depends on the SDI level
when the CNV rising edge occurs. The CS mode is selected if
SDI is high and the chain mode is selected if SDI is low. The
SDI hold time is such that when SDI and CNV are connected
together, the chain mode is always selected.
In either mode, the AD7942 offers the flexibility to optionally
force a start bit in front of the data bits. This start bit can be
used as a busy signal indicator to interrupt the digital host and
trigger the data reading. Otherwise, without a busy indicator,
the user must time out the maximum conversion time prior
to readback.
The busy indicator feature is enabled as follows:
In the CS mode, if CNV or SDI is low when the ADC
conversion ends (see
and
).
In the chain mode, if SCK is high during the CNV rising
edge (see Figure 41).
相关PDF资料 |
PDF描述 |
|---|---|
| D38999/24FJ61BN | CONN HSG RCPT 61POS JAM NUT SCKT |
| AD9283BRSZ-80 | IC ADC 8BIT 80MSPS 3V 20-SSOP |
| D38999/26JC98SALC | CONN HSG PLUG 10POS STRGHT SCKT |
| MS27508E14F35PA | CONN RCPT 37POS BOX MNT W/PINS |
| AD7708BRU-REEL | IC ADC 16BIT R-R 8/10CH 28-TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7942BCPZRL1 | 制造商:AD 制造商全称:Analog Devices 功能描述:14-Bit, 250 kSPS PulSAR, Pseudo Differential ADC in MSOP/QFN |
| AD7942BCPZRL7 | 功能描述:IC ADC 14BIT 250KSPS 10-LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:PulSAR® 其它有关文件:TSA1204 View All Specifications 标准包装:1 系列:- 位数:12 采样率（每秒）:20M 数据接口:并联 转换器数目:2 功率耗散（最大）:155mW 电压电源:模拟和数字 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-TQFP 供应商设备封装:48-TQFP（7x7） 包装:Digi-Reel® 输入数目和类型:4 个单端，单极；2 个差分，单极 产品目录页面:1156 (CN2011-ZH PDF) 其它名称:497-5435-6 |
| AD7942BCPZRL71 | 制造商:AD 制造商全称:Analog Devices 功能描述:14-Bit, 250 kSPS PulSAR, Pseudo Differential ADC in MSOP/QFN |
| AD7942BRM | 制造商:Analog Devices 功能描述:ADC Single SAR 250ksps 14-bit Serial 10-Pin MSOP Tube 制造商:Analog Devices 功能描述:IC 14-BIT ADC |
| AD7942BRMRL7 | 制造商:AD 制造商全称:Analog Devices 功能描述:14-Bit, 250 kSPS PulSAR ADC in MSOP/QFN |
发布紧急采购，3分钟左右您将得到回复。