- 您现在的位置：买卖IC网 > PDF目录294844 > AD7946BRM (ANALOG DEVICES INC) 14-Bit, 500 kSPS PulSAR⑩ ADC in MSOP/QFN PDF资料下载
参数资料
| 型号： | AD7946BRM |
| 厂商： | ANALOG DEVICES INC |
| 元件分类： | ADC |
| 英文描述： | 14-Bit, 500 kSPS PulSAR⑩ ADC in MSOP/QFN |
| 中文描述： | 1-CH 14-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO10 |
| 封装： | MO-187-BA, MSOP-10 |
| 文件页数： | 16/24页 |
| 文件大小： | 637K |
| 代理商： | AD7946BRM |
AD7946
Rev. A | Page 23 of 24
APPLICATION GUIDELINES
LAYOUT
The printed circuit board that houses the AD7946 should be
designed so that the analog and digital sections are separated
and confined to certain areas of the board. The pinout of the
AD7946, with all its analog signals on the left side and all its
digital signals on the right side, eases this task.
Avoid running digital lines under the device because these
couple noise onto the die, unless a ground plane under the
AD7946 is used as a shield. Fast switching signals, such as CNV
or clocks, should never run near analog signal paths. Crossover
of digital and analog signals should be avoided.
At least one ground plane should be used. It could be common
or split between the digital and analog sections. In the latter
case, the planes should be joined underneath the AD7946s.
The AD7946 voltage reference input REF has a dynamic input
impedance and should be decoupled with minimal parasitic
inductances. This is done by placing the reference decoupling
ceramic capacitor close to, and ideally right up against, the REF
and GND pins and connecting it with wide, low impedance
traces.
Finally, the power supplies VDD and VIO of the AD7946
should be decoupled with ceramic capacitors (typically 100 nF)
placed close to the AD7946 and connected using short and wide
traces to provide low impedance paths and reduce the effect of
glitches on the power supply lines.
An example of layout following these rules is shown in
EVALUATING THE AD7946’S PERFORMANCE
Other recommended layouts for the AD7946 are outlined
in the documentation of the evaluation board for the AD7946
(EVAL-AD7946CB). The evaluation board package includes a
fully assembled and tested evaluation board, documentation,
and software for controlling the board from a PC via the
EVAL-CONTROL BRD3.
04656-044
Figure 45. Example of Layout of the AD7946 (Top Layer)
04656-045
Figure 46. Example of Layout of the AD7946 (Bottom Layer)
相关PDF资料 |
PDF描述 |
|---|---|
| AD7946 | 14-Bit, 500 kSPS PulSAR⑩ ADC in MSOP/QFN |
| AD8138-EVAL | Low Distortion Differential ADC Driver |
| AD8138AR | Low Distortion Differential ADC Driver |
| AD8139ACP-REEL | Low Noise Rail-to-Rail Differential ADC Driver |
| AD8139ACP-REEL7 | Low Noise Rail-to-Rail Differential ADC Driver |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7946BRMRL7 | 制造商:AD 制造商全称:Analog Devices 功能描述:14-Bit, 500 kSPS PulSAR⑩ ADC in MSOP/QFN |
| AD7946BRM-RL7 | 制造商:Analog Devices 功能描述:ADC Single SAR 500ksps 14-bit Serial 10-Pin MSOP T/R |
| AD7946BRMZ | 功能描述:IC ADC 14BIT 500KSPS SAR 10-MSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:PulSAR® 其它有关文件:TSA1204 View All Specifications 标准包装:1 系列:- 位数:12 采样率（每秒）:20M 数据接口:并联 转换器数目:2 功率耗散（最大）:155mW 电压电源:模拟和数字 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-TQFP 供应商设备封装:48-TQFP（7x7） 包装:Digi-Reel® 输入数目和类型:4 个单端，单极；2 个差分，单极 产品目录页面:1156 (CN2011-ZH PDF) 其它名称:497-5435-6 |
| AD7946BRMZRL7 | 功能描述:IC ADC 14BIT 500KSPS 10-MSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:PulSAR® 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极 |
| AD7947 | 制造商:AD 制造商全称:Analog Devices 功能描述:3mW, 100kSPS, 14-Bit ADC in 6-Lead SOT-23 |
发布紧急采购，3分钟左右您将得到回复。