- 您现在的位置：买卖IC网 > PDF目录294844 > AD7946BRM (ANALOG DEVICES INC) 14-Bit, 500 kSPS PulSAR⑩ ADC in MSOP/QFN PDF资料下载
参数资料
| 型号： | AD7946BRM |
| 厂商： | ANALOG DEVICES INC |
| 元件分类： | ADC |
| 英文描述： | 14-Bit, 500 kSPS PulSAR⑩ ADC in MSOP/QFN |
| 中文描述： | 1-CH 14-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO10 |
| 封装： | MO-187-BA, MSOP-10 |
| 文件页数： | 9/24页 |
| 文件大小： | 637K |
| 代理商： | AD7946BRM |
AD7946
Rev. A | Page 17 of 24
CS MODE 3-WIRE, NO BUSY INDICATOR
This mode is usually used when a single AD7946 is connected
to an SPI-compatible digital host. The connection diagram is
shown in Figure 33 and the corresponding timing is given in
With SDI tied to VIO, a rising edge on CNV initiates a
conversion, selects the CS mode, and forces SDO to high
impedance. Once a conversion is initiated, it continues to
completion irrespective of the state of CNV. For instance, it
could be useful to bring CNV low to select other SPI devices,
such as analog multiplexers, but CNV must be returned high
before the minimum conversion time and held high until the
maximum conversion time to avoid the generation of the BUSY
signal indicator. When the conversion is complete, the AD7946
enters the acquisition phase and powers down. When CNV
goes low, the MSB is output onto SDO. The remaining data bits
are then clocked by subsequent SCK falling edges. The data is
valid on both SCK edges. Although the rising edge can be used
to capture the data, a digital host using the SCK falling edge
allows a faster reading rate, provided it has an acceptable hold
time. After the 14th SCK falling edge or when CNV goes high,
whichever is earlier, SDO returns to high impedance.
CNV
SCK
SDO
SDI
DATA IN
CLK
CONVERT
VIO
DIGITAL HOST
AD7946
04656-032
Figure 33. CS Mode 3-Wire, No BUSY Indicator
Connection Diagram (SDI High)
SDO
D13
D12
D11
D1
D0
tDIS
SCK
12
3
12
13
14
tSCK
tSCKL
tSCKH
tHSDO
tDSDO
CNV
CONVERSION
ACQUISITION
tCONV
tCYC
ACQUISITION
SDI = 1
tCNVH
tACQ
tEN
04656-033
Figure 34. CS Mode 3-Wire, No BUSY Indicator Serial Interface Timing (SDI High)
相关PDF资料 |
PDF描述 |
|---|---|
| AD7946 | 14-Bit, 500 kSPS PulSAR⑩ ADC in MSOP/QFN |
| AD8138-EVAL | Low Distortion Differential ADC Driver |
| AD8138AR | Low Distortion Differential ADC Driver |
| AD8139ACP-REEL | Low Noise Rail-to-Rail Differential ADC Driver |
| AD8139ACP-REEL7 | Low Noise Rail-to-Rail Differential ADC Driver |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7946BRMRL7 | 制造商:AD 制造商全称:Analog Devices 功能描述:14-Bit, 500 kSPS PulSAR⑩ ADC in MSOP/QFN |
| AD7946BRM-RL7 | 制造商:Analog Devices 功能描述:ADC Single SAR 500ksps 14-bit Serial 10-Pin MSOP T/R |
| AD7946BRMZ | 功能描述:IC ADC 14BIT 500KSPS SAR 10-MSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:PulSAR® 其它有关文件:TSA1204 View All Specifications 标准包装:1 系列:- 位数:12 采样率（每秒）:20M 数据接口:并联 转换器数目:2 功率耗散（最大）:155mW 电压电源:模拟和数字 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-TQFP 供应商设备封装:48-TQFP（7x7） 包装:Digi-Reel® 输入数目和类型:4 个单端，单极；2 个差分，单极 产品目录页面:1156 (CN2011-ZH PDF) 其它名称:497-5435-6 |
| AD7946BRMZRL7 | 功能描述:IC ADC 14BIT 500KSPS 10-MSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:PulSAR® 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极 |
| AD7947 | 制造商:AD 制造商全称:Analog Devices 功能描述:3mW, 100kSPS, 14-Bit ADC in 6-Lead SOT-23 |
发布紧急采购，3分钟左右您将得到回复。