- 您现在的位置：买卖IC网 > PDF目录10659 > AD7983BRMZ (Analog Devices Inc)IC ADC 16BIT 1.33MSPS 10MSOP PDF资料下载
参数资料
| 型号： | AD7983BRMZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 16/24页 |
| 文件大小： | 0K |
| 描述： | IC ADC 16BIT 1.33MSPS 10MSOP |
| 标准包装： | 1 |
| 系列： | PulSAR® |
| 位数： | 16 |
| 采样率（每秒）： | 1.33M |
| 数据接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 12mW |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 10-MSOP |
| 包装： | 管件 |
| 输入数目和类型： | 1 个差分，单极 |
| 产品目录页面： | 780 (CN2011-ZH PDF) |
AD7983
Rev. A | Page 23 of 24
APPLICATION HINTS
LAYOUT
The printed circuit board (PCB) that houses the AD7983
should be designed so that the analog and digital sections are
separated and confined to certain areas of the board. The pinout of
the AD7983, with all its analog signals on the left side and all its
digital signals on the right side, eases this task.
Avoid running digital lines under the device because these couple
noise onto the die, unless a ground plane under the AD7983 is
used as a shield. Fast switching signals, such as CNV or clocks,
should never run near analog signal paths. Crossover of digital
and analog signals should be avoided.
At least one ground plane should be used. It can be common or
split between the digital and analog section. In the latter case,
the planes should be joined underneath the AD7983.
The AD7983 voltage reference input REF has a dynamic input
impedance and should be decoupled with minimal parasitic
inductances. This is done by placing the reference decoupling
ceramic capacitor close to, ideally right up against, the REF and
GND pins and connecting them with wide, low impedance traces.
Finally, the AD7983 power supplies, VDD and VIO, should be
decoupled with ceramic capacitors, typically 100 nF, placed
close to the AD7983 and connected using short and wide traces
to provide low impedance paths and to reduce the effect of
glitches on the power supply lines.
An example of a layout following these rules is shown in
EVALUATING THE PERFORMANCE OF THE AD7983
Other recommended layouts for the AD7983 are outlined
in the documentation of the evaluation board for the AD7983
(EVAL-AD7983CBZ). The evaluation board package includes
a fully assembled and tested evaluation board, documentation,
and software for controlling the board from a PC via the
EVAL-CONTROL BRD.
AD7983
0
69
74
-02
4
Figure 38. Example Layout of the AD7983 (Top Layer)
06
97
4-
02
5
Figure 39. Example Layout of the AD7983 (Bottom Layer)
相关PDF资料 |
PDF描述 |
|---|---|
| MAX3362EKA#TG16 | IC TXRX RS485/422 SGL SOT23-8 |
| VI-J1L-MW-F3 | CONVERTER MOD DC/DC 28V 100W |
| AD1674ARZ | IC ADC 12BIT 100KSPS 28-SOIC |
| AD7693BRMZ | IC ADC 16BIT 500KSPS 10-MSOP |
| VI-J1L-MW-F2 | CONVERTER MOD DC/DC 28V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7983BRMZRL7 | 制造商:AD 制造商全称:Analog Devices 功能描述:16-Bit, 1.33 MSPS PulSAR ADC in MSOP/QFN |
| AD7983BRMZ-RL7 | 功能描述:IC ADC 16BIT 1.33MSPS 10MSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:PulSAR® 标准包装:1 系列:- 位数:14 采样率（每秒）:83k 数据接口:串行，并联 转换器数目:1 功率耗散（最大）:95mW 电压电源:双 ± 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:28-DIP（0.600"，15.24mm） 供应商设备封装:28-PDIP 包装:管件 输入数目和类型:1 个单端，双极 |
| AD7984 | 制造商:AD 制造商全称:Analog Devices 功能描述:18-Bit, 1.33 MSPS PulSAR 10.5 mW ADC in MSOP/QFN |
| AD79841 | 制造商:AD 制造商全称:Analog Devices 功能描述:18-Bit, 2 MSPS PulSAR 15 mW ADC in LFCSP (QFN) |
| AD7984BCPZ | 制造商:AD 制造商全称:Analog Devices 功能描述:18-Bit, 1.33 MSPS PulSAR 10.5 mW ADC in MSOP/QFN |
发布紧急采购，3分钟左右您将得到回复。