参数资料
| 型号： | AD8013ANZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 12/12页 |
| 文件大小： | 0K |
| 描述： | IC OPAMP SINGLE 14DIP |
| 标准包装： | 25 |
| 应用： | 电流反馈 |
| 电路数： | 3 |
| -3db带宽： | 140MHz |
| 转换速率： | 1000 V/µs |
| 电流 - 电源： | 3.5mA |
| 电流 - 输出 / 通道： | 30mA |
| 电压 - 电源，单路/双路(±)： | 4.2 V ~ 13 V，±2.1 V ~ 6.5 V |
| 安装类型： | 通孔 |
| 封装/外壳： | 14-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 14-PDIP |
| 包装： | 管件 |
–9–
REV. A
AD8013
FREQUENCY – Hz
1M
1G
10M
CLOSED-LOOP
GAIN
(NORMALIZED)
–
dB
100M
–6
+1
0
–1
–2
–3
–4
–5
180
90
0
–90
PHASE
SHIFT
–
Degrees
G = –10
RL = 150
VS = ±5V
VS = +5V
VS = ±5V
GAIN
PHASE
Figure 27. Closed-Loop Gain and Phase vs. Frequency,
G = –10, RL = 150
To estimate the –3 dB bandwidth for closed-loop gains of 2 or
greater, for feedback resistors not listed in the following table,
the following single pole model for the AD8013 may be used:
ACL
G
1
+ SC
T ( RF + Gn rin )
where:
CT = transcapacitance
1 pF
RF = feedback resistor
G = ideal closed loop gain
Gn = 1 +
R
F
R
G
= noise gain
rin = inverting input resistance
150
ACL = closed loop gain
The –3 dB bandwidth is determined from this model as:
f3
1
2
π C
T ( RF + Gn rin )
This model will predict –3 dB bandwidth to within about 10%
to 15% of the correct value when the load is 150
and V
S =
±5 V. For lower supply voltages there will be a slight decrease in
bandwidth. The model is not accurate enough to predict either
the phase behavior or the frequency response peaking of the
AD8013.
It should be noted that the bandwidth is affected by attenuation
due to the finite input resistance. Also, the open-loop output
resistance of about 12
reduces the bandwidth somewhat when
driving load resistors less than about 250
. (Bandwidths will
be about 10% greater for load resistances above a few hundred
ohms.)
Table I. –3 dB Bandwidth vs. Closed-Loop Gain and Feedback
Resistor, RL = 150 (SOIC)
VS – Volts
Gain
RF – Ohms
BW – MHz
±5
+1
2000
230
+2
845 (931)
150 (135)
+10
301
80
–1
698 (825)
140 (130)
–10
499
85
+5
+1
2000
180
+2
887 (931)
120 (130)
+10
301
75
–1
698 (825)
130 (120)
–10
499
80
Driving Capacitive Loads
When used in combination with the appropriate feedback
resistor, the AD8013 will drive any load capacitance without
oscillation. The general rule for current feedback amplifiers is
that the higher the load capacitance, the higher the feedback
resistor required for stable operation. Due to the high open-loop
transresistance and low inverting input current of the AD8013,
the use of a large feedback resistor does not result in large closed-
loop gain errors. Additionally, its high output short circuit current
makes possible rapid voltage slewing on large load capacitors.
For the best combination of wide bandwidth and clean pulse
response, a small output series resistor is also recommended.
Table II contains values of feedback and series resistors which
result in the best pulse responses. Figure 29 shows the AD8013
driving a 300 pF capacitor through a large voltage step with
virtually no overshoot. (In this case, the large and small signal
pulse responses are quite similar in appearance.)
General
The AD8013 is a wide bandwidth, triple video amplifier that
offers a high level of performance on less than 4.0 mA per
amplifier of quiescent supply current. The AD8013 uses a
proprietary enhancement of a conventional current feedback
architecture, and achieves bandwidth in excess of 200 MHz with
low differential gain and phase errors, making it an extremely
efficient video amplifier.
The AD8013’s wide phase margin coupled with a high output
short circuit current make it an excellent choice when driving
any capacitive load. High open-loop gain and low inverting
input bias current enable it to be used with large values of
feedback resistor with very low closed-loop gain errors.
It is designed to offer outstanding functionality and performance
at closed-loop inverting or noninverting gains of one or greater.
Choice of Feedback & Gain Resistors
Because it is a current feedback amplifier, the closed-loop band-
width of the AD8013 may be customized using different values
of the feedback resistor. Table I shows typical bandwidths at
different supply voltages for some useful closed-loop gains when
driving a load of 150
.
The choice of feedback resistor is not critical unless it is
important to maintain the widest, flattest frequency response.
The resistors recommended in the table are those (chip
resistors) that will result in the widest 0.1 dB bandwidth without
peaking. In applications requiring the best control of bandwidth,
1% resistors are adequate. Package parasitics vary between the
14-pin plastic DIP and the 14-pin plastic SOIC, and may result
in a slight difference in the value of the feedback resistor used to
achieve the optimum dynamic performance. Resistor values and
widest bandwidth figures are shown in parenthesis for the SOIC
where they differ from those of the DIP. Wider bandwidths than
those in the table can be attained by reducing the magnitude of
the feedback resistor (at the expense of increased peaking),
while peaking can be reduced by increasing the magnitude of
the feedback resistor.
Increasing the feedback resistor is especially useful when driving
large capacitive loads as it will increase the phase margin of the
closed-loop circuit. (Refer to the section on driving capacitive
loads for more information.)
相关PDF资料 |
PDF描述 |
|---|---|
| AD8023ARZ | IC AMP VIDEO TRIPLE HC 14-SOIC |
| AD8073JNZ | IC VIDEO AMP TRIPLE 14-DIP |
| AD8074ARU | IC TRPL VID BUFF 500MHZ 16-TSSOP |
| AD810AN | IC CURR-FDBK AMP VIDEO LP 8-DIP |
| AD811AR-16 | IC CURR-FDBK AMP VIDEO HS 16SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD8013AR-14 | 功能描述:IC OPAMP SINGLE SUPPLY 14-SOIC RoHS:否 类别:集成电路 (IC) >> 线性 - 放大器 - 视频放大器和频缓冲器 系列:- 标准包装:1,000 系列:- 应用:驱动器 输出类型:差分 电路数:3 -3db带宽:350MHz 转换速率:1000 V/µs 电流 - 电源:14.5mA 电流 - 输出 / 通道:60mA 电压 - 电源，单路/双路(±):5 V ~ 12 V，±2.5 V ~ 6 V 安装类型:表面贴装 封装/外壳:20-VFQFN 裸露焊盘 供应商设备封装:20-QFN 裸露焊盘（4x4） 包装:带卷 (TR) |
| AD8013AR-14-EBZ | 功能描述:BOARD EVAL FOR AD8013AR-14 RoHS:是 类别:编程器，开发系统 >> 评估板 - 运算放大器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- |
| AD8013AR-14-REEL | 制造商:Analog Devices 功能描述:OP Amp Triple Current Fdbk 制造商:Rochester Electronics LLC 功能描述:TRPL LO PWR VIDEO OP AMP - Tape and Reel |
| AD8013AR-14-REEL7 | 制造商:Analog Devices 功能描述:OP Amp Triple Current Fdbk ±6.5V/13V 14-Pin SOIC N T/R 制造商:Rochester Electronics LLC 功能描述:TRPL LO PWR VIDEO OP AMP - Tape and Reel |
| AD8013ARZ-14 | 功能描述:IC AMP VIDEO SGL SUPP LP 14-SOIC RoHS:是 类别:集成电路 (IC) >> 线性 - 放大器 - 视频放大器和频缓冲器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 应用:TFT-LCD 面板：VCOM 驱动器 输出类型:满摆幅 电路数:1 -3db带宽:35MHz 转换速率:40 V/µs 电流 - 电源:3.7mA 电流 - 输出 / 通道:1.3A 电压 - 电源，单路/双路(±):9 V ~ 20 V，±4.5 V ~ 10 V 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽）裸露焊盘 供应商设备封装:8-uMax-EP 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。