- 您现在的位置：买卖IC网 > PDF目录10791 > AD8016ARBZ (Analog Devices Inc)IC AMP XDSL LINE DVR 24-SOIC PDF资料下载
参数资料
| 型号： | AD8016ARBZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 11/21页 |
| 文件大小： | 0K |
| 描述： | IC AMP XDSL LINE DVR 24-SOIC |
| 标准包装： | 31 |
| 类型： | 驱动器 |
| 驱动器/接收器数： | 2/0 |
| 规程： | xDSL |
| 电源电压： | 3 V ~ 13 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-SOIC（0.295"，7.50mm 宽）18 引线，熔断式引线 |
| 供应商设备封装： | 24-SOIC，带蝙蝠翼 |
| 包装： | 管件 |
| 产品目录页面： | 772 (CN2011-ZH PDF) |
| 配用： | AD8016ARB-EVAL-ND - BOARD EVAL FOR AD8016ARB |
AD8016
Data Sheet
Rev. C | Page 18 of 20
THERMAL ENHANCEMENTS AND PCB LAYOUT
There are several ways to enhance the thermal capacity of the
CO solution. Additional thermal capacity can be created using
enhanced PCB layout techniques such as interlacing (some-
times referred to as stitching or interconnection) of the layers
immediately beneath the line driver. This technique serves to
increase the thermal mass or capacity of the PCB immediately
beneath the driver. The AD8016 in a TSSOP_EP (ARE model)
package can be designed to operate in the CO solution using
prudent measures to manage the power dissipation through
careful PCB design. The ARE package is available for use in
designing the highest density CO solutions. Maximum heat
transfer to the PCB can be accomplished using the ARE
package when the thermal slug is soldered to an exposed
copper pad directly beneath the AD8016. Optimum thermal
performance can be achieved in the ARE package only when
the back of the package is soldered to a PCB designed for
maximum thermal capacity (see Figure 48). Thermal experi-
ments with the ARE package were conducted without soldering
the heat slug to the PCB. Heat transfer was through physical
contact only. The following offers some insight into the AD8016
power dissipation and relative junction temperature, as well as
the effects of PCB size and composition on the junction-to-air
thermal resistance or θJA.
THERMAL TESTING
A wind tunnel study was conducted to determine the relation-
ship between thermal capacity (that is, printed circuit board
copper area), air flow, and junction temperature. Junction-to-
ambient thermal resistance, θJA, was also calculated for the
operated in a noninverting differential driver configuration,
typical of an xDSL application yet isolated from any other
modem components. Testing was conducted using a 1 oz.
copper board in an ambient temperature of ~24°C over air
flows of 200, 150, 100, and 50 linear feet per minute (LFM)
(0.200 and 400 for AD8016 ARE) and for the ARB packages as
well as in still air. The 4-layer PCB was designed to maximize
the area of copper on the outer two layers of the board, while
the inner layers were used to configure the AD8016 in a
differential driver circuit. The PCB measured 3 inches ×
4 inches in the beginning of the study and was progressively
reduced in size to approximately 2 inches × 2 inches. The
testing was performed in a wind tunnel to control airflow
in units of LFM. The tunnel is approximately 11 inches in
diameter.
AIR FLOW TEST CONDITIONS
DUT Power
A typical DSL DMT signal produces about 1.5 W of power
dissipation in the AD8016 package. The fully biased (PWDN0
and PWDN1 = Logic 1) quiescent current of the AD8016 is
~25 mA. A 1 MHz differential sine wave at an amplitude of
8 V p-p/amplifier into an RLOAD of 100 Ω differential (50 Ω
per side) produces the 1.5 W of power typical in the AD8016
device. (See the Power Dissipation section for details.)
Thermal Resistance
ARB or SOIC_W_BAT package is 8.6°C/W and for the AD8016
ARE or TSSOP_EP it is 5.6°C/W. These package specifications
were used in this study to determine junction temperature
based on the measured case temperature.
PCB Dimensions of a Differential Driver Circuit
Several components are required to support the AD8016 in a
differential driver circuit. The PCB area necessary for these
components (that is, feedback and gain resistors, ac-coupling
and decoupling capacitors, termination and load resistors)
dictated the area of the smallest PCB in this study, 4.7 square
inches. Further reduction in PCB area, although possible, has
consequences in terms of the maximum operating junction
temperature method of thermal enhancement.) A cooling fan
that draws moving air over the PCB and xDSL drivers, while
not always required, may be useful in reducing the operating
temperature.
相关PDF资料 |
PDF描述 |
|---|---|
| VI-JTR-MY-S | CONVERTER MOD DC/DC 7.5V 50W |
| AD790AQ | IC PREC COMPARATOR HS 8-CDIP |
| LTC1518CS#PBF | IC LINE RCVR RS485 QUAD 16-SOIC |
| LTC7545ABG#PBF | IC D/ACONV MULTIPLY 12BIT 20SSOP |
| ADCMP582BCPZ-R2 | IC COMPARATOR PECL UFAST 16LFCSP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD8016ARBZ | 制造商:Analog Devices 功能描述:LINE DRIVER, DUAL, 1000 V/us, WSOIC-24 |
| AD8016ARBZ-REEL | 功能描述:IC AMP XDSL LINE DVR 24-SOIC TR RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:27 系列:- 类型:收发器 驱动器/接收器数:3/3 规程:RS232，RS485 电源电压:4.75 V ~ 5.25 V 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC 包装:管件 |
| AD8016ARE | 制造商:Analog Devices 功能描述:ADSL Driver Dual 28-Pin TSSOP EP Tube 制造商:Rochester Electronics LLC 功能描述:TSSOP LOW POWER, HIGH OUTPUT CURRENT AMP - Bulk |
| AD8016ARE-EVAL | 功能描述:BOARD EVAL FOR AD8016ARE RoHS:否 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081 |
| AD8016ARE-REEL | 制造商:Analog Devices 功能描述:ADSL Driver Dual 28-Pin TSSOP EP T/R 制造商:Rochester Electronics LLC 功能描述:TSSOP LOW POWER, HIGH OUTPUT CURRENT AMP - Tape and Reel |
发布紧急采购，3分钟左右您将得到回复。