参数资料
型号: AD8065ART-EBZ
厂商: Analog Devices Inc
文件页数: 16/29页
文件大小: 0K
描述: BOARD EVAL FOR AD8065ART
标准包装: 1
每 IC 通道数: 1 - 单
放大器类型: 电压反馈
板类型: 裸(未填充)
已供物品:
已用 IC / 零件: SOT-23-5 封装
AD8065/AD8066
Rev. J | Page 22 of 28
THERMAL CONSIDERATIONS
INPUT AND OUTPUT OVERLOAD BEHAVIOR
With 24 V power supplies and 6.5 mA quiescent current, the
AD8065 dissipates 156 mW with no load. The AD8066 dissipates
312 mW. This can lead to noticeable thermal effects, especially
in the small SOT-23-5 (thermal resistance of 160°C/W). VOS
temperature drift is trimmed to guarantee a maximum drift of
17 μV/°C, so it can change up to 0.425 mV due to warm-up
effects for an AD8065/AD8066 in a SOT-23-5 package on 24 V.
A simplified schematic of the AD8065/AD8066 input stage is
shown in Figure 56. This shows the cascoded N-channel JFET
input pair, the ESD and other protection diodes, and the
auxiliary NPN input stage that eliminates any phase inversion
behavior. When the common-mode input voltage to the amplifier
is driven to within approximately 3 V of the positive power supply,
the input JFET’s bias current turns off and the bias of the NPN
pair turns on, taking over control of the amplifier. The NPN
differential pair now sets the amplifier’s offset, and the input
bias current is now in the range of several tens of microamps.
This behavior is shown in Figure 32. Normal operation resumes
when the common-mode voltage goes below the 3 V from the
positive supply threshold.
Ib increases by a factor of 1.7 for every 10°C rise in temperature.
Ib is close to five times higher at 24 V supplies as opposed to a
single 5 V supply.
Heavy loads increase power dissipation and raise the chip
junction temperature as described in the Maximum Power
Dissipation section. Care should be taken not to exceed the
rated power dissipation of the package.
The output transistors of the rail-to-rail output stage have
circuitry to limit the extent of their saturation when the output
is overdriven. This helps output recovery time. Output recovery
from a 0.5 V output overdrive on a ±5 V supply is shown in
VTHRESHOLD
VBIAS
S
VP
TO REST OF AMP
VCC
S
VN
R1
Q2
Q5
Q3
Q1
Q6
Q7
Q4
R5
D1
R6
R3
R4
R2
R8
R7
D2
D3
D4
–VEE
IT1
IT2
02916-E
-056
Figure 56. Simplified Input Stage
相关PDF资料
PDF描述
VE-J7Y-EY CONVERTER MOD DC/DC 3.3V 33W
AD8138ARM-EBZ BOARD EVAL FOR AD8138ARM
VE-J7X-EY CONVERTER MOD DC/DC 5.2V 50W
AD8129AR-EBZ BOARD EVAL FOR AD8129AR
RYM08DTBD CONN EDGECARD 16POS R/A .156 SLD
相关代理商/技术参数
参数描述
AD8065ART-R2 制造商:Analog Devices 功能描述:OP Amp Single Volt Fdbk R-R O/P 制造商:Analog Devices 功能描述:OP Amp Single Volt Fdbk R-R O/P ±12V/24V 5-Pin SOT-23 T/R 制造商:Analog Devices 功能描述:OP AMP SGL VOLT FDBK R-R O/P 12V/24V 5PIN SOT-23 - Tape and Reel 制造商:Rochester Electronics LLC 功能描述:SOT23 HI PERF HI SPD FET AMP W/ DISABLE - Bulk 制造商:Analog Devices 功能描述:IC OP-AMP HIGH PERFORMANCE
AD8065ART-REEL 功能描述:IC OPAMP VF R-R LN LP SOT23-5 RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:FastFET™ 标准包装:50 系列:- 放大器类型:通用 电路数:2 输出类型:满摆幅 转换速率:1.8 V/µs 增益带宽积:6.5MHz -3db带宽:4.5MHz 电流 - 输入偏压:5nA 电压 - 输入偏移:100µV 电流 - 电源:65µA 电流 - 输出 / 通道:35mA 电压 - 电源,单路/双路(±):1.8 V ~ 5.25 V,±0.9 V ~ 2.625 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP,10-MSOP(0.118",3.00mm 宽) 供应商设备封装:10-MSOP 包装:管件
AD8065ART-REEL7 功能描述:IC OPAMP VF R-R LN LP SOT23-5 RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:FastFET™ 标准包装:50 系列:- 放大器类型:通用 电路数:2 输出类型:满摆幅 转换速率:1.8 V/µs 增益带宽积:6.5MHz -3db带宽:4.5MHz 电流 - 输入偏压:5nA 电压 - 输入偏移:100µV 电流 - 电源:65µA 电流 - 输出 / 通道:35mA 电压 - 电源,单路/双路(±):1.8 V ~ 5.25 V,±0.9 V ~ 2.625 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP,10-MSOP(0.118",3.00mm 宽) 供应商设备封装:10-MSOP 包装:管件
AD8065ARTZ-R2 制造商:Analog Devices 功能描述:OP AMP SGL VOLT FDBK R-R O/P 12V/24V 5PIN SOT-23 - Tape and Reel 制造商:Analog Devices 功能描述:IC OP AMP SINGLE 145MHZ 5SOT23 制造商:Analog Devices 功能描述:IC OPERATIONAL AMPLIFIER SINGLE BIPOL 制造商:Analog Devices 功能描述:IC, OP AMP, SINGLE, 145MHZ, 5SOT23 制造商:Analog Devices 功能描述:OP Amp Single Volt Fdbk R-R O/P 12V/24V
AD8065ARTZ-R2 制造商:Analog Devices 功能描述:Operational Amplifier (Op-Amp) IC