参数资料
| 型号： | AD8131ARZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 11/21页 |
| 文件大小： | 0K |
| 描述： | IC AMP DIFF LDIST 60MA 8SOIC |
| 标准包装： | 98 |
| 放大器类型： | 差分 |
| 电路数： | 1 |
| 输出类型： | 差分 |
| 转换速率： | 2000 V/µs |
| -3db带宽： | 400MHz |
| 电流 - 输入偏压： | 500nA |
| 电压 - 输入偏移： | 1500µV |
| 电流 - 电源： | 11.5mA |
| 电流 - 输出 / 通道： | 60mA |
| 电压 - 电源，单路/双路(±)： | 2.8 V ~ 11 V，±1.4 V ~ 5.5 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SO |
| 包装： | 管件 |
| 产品目录页面： | 765 (CN2011-ZH PDF) |
AD8131
Rev. B | Page 18 of 20
APPLICATIONS
TWISTED-PAIR LINE DRIVER
The AD8131 has on-chip resistors that provide for a gain of 2
without any external parts. Several on-chip resistors are
trimmed to ensure that the gain is accurate, the common-mode
rejection is good, and the output is well balanced. This makes
the AD8131 very suitable as a single-ended-to-differential
twisted-pair line driver.
Figure 40 shows a circuit of an AD8131 driving a twisted-pair
line, like a Category 3 or Category 5 (Cat3 or Cat5), that is
already installed in many buildings for telephony and data
communications. The characteristic impedance of such a
transmission line is usually about 100 Ω. The outstanding
balance of the AD8131 output will minimize the common-
mode signal and therefore the amount of EMI generated by
driving the twisted pair.
The two resistors in series with each output terminate the line at
the transmit end. Since the impedances of the outputs of the
AD8131 are very low, they can be thought of as a short-circuit,
and the two terminating resistors form a 100 Ω termination at
the transmit end of the transmission line. The receive end is
directly terminated by a 100 Ω resistor across the line.
This back-termination of the transmission line divides the
output signal by two. The fixed gain of 2 of the AD8131 will
create a net unity gain for the system from end to end.
In this case, the input signal is provided by a signal generator
with an output impedance of 50 Ω. This is terminated with a
49.9 Ω resistor near +DIN of the AD8131. The effective parallel
resistance of the source and termination is 25 Ω.The 24.9 Ω
resistor from DIN to ground matches the +DIN source
impedance and minimizes any dc and gain errors.
If +DIN is driven by a low-impedance source over a short
distance, such as the output of an op amp, then no termination
resistor is required at +DIN. In this case, the DIN can be directly
tied to ground.
AD8131
8
2
3
6
5
4
+
1
24.9
Ω
49.9
Ω
100
Ω
10
μF
0.1
μF
49.9
Ω
49.9
Ω
10
μF
0.1
μF
+5V
–5V
RECEIVER
01072-040
Figure 40. Single-Ended-to-Differential 100 Ω Line Driver
3 V SUPPLY DIFFERENTIAL A-TO-D DRIVER
Many newer ADCs can run from a single 3 V supply, which can
save significant system power. In order to increase the dynamic
range at the analog input, they have differential inputs, which
double the dynamic range with respect to a single-ended input.
An added benefit of using a differential input is that the
distortion can be improved.
The low distortion and ability to run from a single 3 V supply make
the AD8131 suited as an A-to-D driver for some 10-bit, single-
supply applications. Figure 41 shows a schematic for a circuit for an
AD8131 driving an AD9203, a 10-bit, 40 MSPS ADC.
The common mode of the AD8131 output is set at midsupply
by the voltage divider connected to VOCM, and ac-bypassed with
a 0.1 μF capacitor. This provides for maximum dynamic range
between the supplies at the output of the AD8131. The 110 Ω
resistors at the AD8131 output, along with the shunt capacitors
form a one pole, low-pass filter for lowering noise and
antialiasing.
AD8131
8
2
3
6
+
3V
LPF
+3V
1
20pF
AD9203
26
25
28
AVDD
DRVDD
AINP
AINN
AVSS
DRVSS
3V
27
1
2
DIGITAL
OUTPUTS
0.1 F
10 F
0.1 F
110
Ω
110
Ω
24.9
Ω
49.9
Ω
10k
Ω
10k
Ω
VOCM
01072-041
Figure 41. Test Circuit for AD8131 Driving an AD9203, 10-Bit, 40 MSPS ADC
Figure 42 shows an FFT plot that was taken from the combined
devices at an analog input frequency of 2.5 MHz and a 40 MSPS
sampling rate. The performance of the AD8131 compares very
favorably with a center-tapped transformer drive, which has
typically been the best way to drive this ADC. The AD8131 has
the advantage of maintaining dc performance, which a
transformer solution cannot provide.
相关PDF资料 |
PDF描述 |
|---|---|
| 10075025-G01-20ULF | CONN HEADER 20PS DL STR 2MM GOLD |
| SBH31-NBPB-D22-ST-BK | CONN HEADER 1.27MM 44POS GOLD |
| PEC18SABN | CONN HEADER .100 SINGL STR 18POS |
| SMH101-LPSE-D05-SP-BK | CONN HEADER 10POS 1MM DL AU SMD |
| 10-89-7202 | CONN HDR DUAL 20POS .100 SRT AU |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD8131ARZ-REEL | 功能描述:IC AMP DIFF LDIST 60MA 8SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:50 系列:- 放大器类型:通用 电路数:2 输出类型:满摆幅 转换速率:1.8 V/µs 增益带宽积:6.5MHz -3db带宽:4.5MHz 电流 - 输入偏压:5nA 电压 - 输入偏移:100µV 电流 - 电源:65µA 电流 - 输出 / 通道:35mA 电压 - 电源，单路/双路(±):1.8 V ~ 5.25 V，±0.9 V ~ 2.625 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| AD8131ARZ-REEL7 | 功能描述:IC AMP DIFF LDIST 60MA 8SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:50 系列:LinCMOS™ 放大器类型:通用 电路数:4 输出类型:- 转换速率:0.05 V/µs 增益带宽积:110kHz -3db带宽:- 电流 - 输入偏压:0.7pA 电压 - 输入偏移:210µV 电流 - 电源:57µA 电流 - 输出 / 通道:30mA 电压 - 电源，单路/双路(±):3 V ~ 16 V，±1.5 V ~ 8 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SOIC 包装:管件 产品目录页面:865 (CN2011-ZH PDF) 其它名称:296-1834296-1834-5 |
| AD8131-EVAL | 制造商:AD 制造商全称:Analog Devices 功能描述:Low-Cost, High-Speed Differential Driver |
| AD8132 | 制造商:AD 制造商全称:Analog Devices 功能描述:Low-Cost, High-Speed Differential Amplifier |
| AD8132_06 | 制造商:AD 制造商全称:Analog Devices 功能描述:Low Cost, High Speed Differential Amplifier |
发布紧急采购，3分钟左右您将得到回复。