- 您现在的位置：买卖IC网 > PDF目录8611 > AD8138ARMZ-REEL (Analog Devices Inc)IC AMP DIFF LDIST LP 95MA 8MSOP PDF资料下载
参数资料
| 型号： | AD8138ARMZ-REEL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 11/25页 |
| 文件大小： | 0K |
| 描述： | IC AMP DIFF LDIST LP 95MA 8MSOP |
| 设计资源： | DC-Coupled, Single-Ended-to-Differential Conversion Using AD8138 and AD7352 (CN0040) DC-Coupled, Single-Ended-to-Differential Conversion Using AD8138 and AD7356 (CN0041) DC-Coupled, Single-Ended-to-Differential Conversion Using AD8138 and AD7357 (CN0061) |
| 标准包装： | 3,000 |
| 类型： | ADC 驱动器 |
| 应用： | 数据采集 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-MSOP |
| 包装： | 带卷 (TR) |
AD8138
Rev. F | Page 18 of 24
When using the AD8138 in gain configurations where
G
F
R
of one feedback network is unequal to
G
F
R
of the other network, there is a differential output noise due to
input-referred voltage in the VOCM circuitry. The output noise is
defined in terms of the following feedback terms (refer to
G
F
G
R
+
=
β
1
for OUT to +IN loop, and
G
F
G
R
+
=
β
2
for +OUT to IN loop. With these defined,
β
+
β
β
=
2
1
2
1
,
2
OCM
V
nIN
dm
nOUT
V
where VnOUT, dm is the output differential noise, and
is
the input-referred voltage noise in VOCM.
COM
V
nIN
V
,
THE IMPACT OF MISMATCHES IN THE FEEDBACK
NETWORKS
As previously mentioned, even if the external feedback
networks (RF/RG) are mismatched, the internal common-mode
feedback loop still forces the outputs to remain balanced. The
amplitudes of the signals at each output remains equal and 180°
out of phase. The input-to-output differential-mode gain varies
proportionately to the feedback mismatch, but the output
balance is unaffected.
Ratio matching errors in the external resistors result in a
degradation of the circuit’s ability to reject input common-
mode signals, much the same as for a four-resistor difference
amplifier made from a conventional op amp.
In addition, if the dc levels of the input and output common-
mode voltages are different, matching errors result in a small
differential-mode output offset voltage. For the G = 1 case, with
a ground referenced input signal and the output common-mode
level set for 2.5 V, an output offset of as much as 25 mV (1% of
the difference in common-mode levels) can result if 1% tolerance
resistors are used. Resistors of 1% tolerance result in a worst-
case input CMRR of about 40 dB, worst-case differential mode
output offset of 25 mV due to 2.5 V level-shift, and no significant
degradation in output balance error.
CALCULATING AN APPLICATION CIRCUIT’S INPUT
IMPEDANCE
The effective input impedance of a circuit such as the one in
Figure 42, at +DIN and –DIN, depends on whether the amplifier is
being driven by a single-ended or differential signal source. For
balanced differential input signals, the input impedance (RIN, dm)
between the inputs (+DIN and DIN) is simply
RIN, dm =2 × RG
In the case of a single-ended input signal (for example if DIN is
grounded and the input signal is applied to +DIN), the input
impedance becomes
()
+
×
=
F
G
F
G
dm
IN
R
2
1
,
The circuit’s input impedance is effectively higher than it would
be for a conventional op amp connected as an inverter because
a fraction of the differential output voltage appears at the inputs
as a common-mode signal, partially bootstrapping the voltage
across the input resistor RG.
INPUT COMMON-MODE VOLTAGE RANGE IN
SINGLE-SUPPLY APPLICATIONS
The AD8138 is optimized for level-shifting, ground-referenced
input signals. For a single-ended input, this would imply, for
when the amplifier’s negative power supply voltage (at V) is
also set to 0 V.
SETTING THE OUTPUT COMMON-MODE VOLTAGE
The AD8138’s VOCM pin is internally biased at a voltage
approximately equal to the midsupply point (average value of
the voltages on V+ and V). Relying on this internal bias results
in an output common-mode voltage that is within about
100 mV of the expected value.
In cases where more accurate control of the output common-
mode level is required, it is recommended that an external
source, or resistor divider (made up of 10 kΩ resistors), be used.
The output common-mode offset listed in the Specifications
section assumes the VOCM input is driven by a low impedance
voltage source.
DRIVING A CAPACITIVE LOAD
A purely capacitive load can react with the pin and bondwire
inductance of the AD8138, resulting in high frequency ringing
in the pulse response. One way to minimize this effect is to
place a small capacitor across each of the feedback resistors. The
added capacitance should be small to avoid destabilizing the
amplifier. An alternative technique is to place a small resistor in
series with the amplifier’s outputs, as shown in Figure 40.
相关PDF资料 |
PDF描述 |
|---|---|
| VE-24L-IV-F4 | CONVERTER MOD DC/DC 28V 150W |
| LTC6406IMS8E#PBF | IC AMP/DRIVER DIFF 8-MSOP |
| VI-24H-MW-B1 | CONVERTER MOD DC/DC 52V 100W |
| VE-24L-IV-F3 | CONVERTER MOD DC/DC 28V 150W |
| VI-24F-MW-B1 | CONVERTER MOD DC/DC 72V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD8138ARMZ-REEL7 | 功能描述:IC AMP DIFF LDIST LP 95MA 8MSOP RoHS:是 类别:集成电路 (IC) >> 线性 - 放大器 - 专用 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:60 系列:- 类型:可变增益放大器 应用:CATV 安装类型:表面贴装 封装/外壳:20-WQFN 裸露焊盘 供应商设备封装:20-TQFN-EP（5x5） 包装:托盘 |
| AD8138AR-REEL | 功能描述:IC AMP DIFF LDIST LP 95MA 8SOIC RoHS:否 类别:集成电路 (IC) >> 线性 - 放大器 - 专用 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:60 系列:- 类型:可变增益放大器 应用:CATV 安装类型:表面贴装 封装/外壳:20-WQFN 裸露焊盘 供应商设备封装:20-TQFN-EP（5x5） 包装:托盘 |
| AD8138AR-REEL7 | 功能描述:IC AMP DIFF LDIST LP 95MA 8SOIC RoHS:否 类别:集成电路 (IC) >> 线性 - 放大器 - 专用 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:60 系列:- 类型:可变增益放大器 应用:CATV 安装类型:表面贴装 封装/外壳:20-WQFN 裸露焊盘 供应商设备封装:20-TQFN-EP（5x5） 包装:托盘 |
| AD8138ARZ | 功能描述:IC AMP DIFF LDIST LP 95MA 8SOIC RoHS:是 类别:集成电路 (IC) >> 线性 - 放大器 - 专用 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:60 系列:- 类型:可变增益放大器 应用:CATV 安装类型:表面贴装 封装/外壳:20-WQFN 裸露焊盘 供应商设备封装:20-TQFN-EP（5x5） 包装:托盘 |
| AD8138ARZ-R7 | 功能描述:IC AMP DIFF LDIST LP 95MA 8SOIC RoHS:是 类别:集成电路 (IC) >> 线性 - 放大器 - 专用 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:60 系列:- 类型:可变增益放大器 应用:CATV 安装类型:表面贴装 封装/外壳:20-WQFN 裸露焊盘 供应商设备封装:20-TQFN-EP（5x5） 包装:托盘 |
发布紧急采购，3分钟左右您将得到回复。