参数资料
| 型号： | AD8139ARDZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 13/25页 |
| 文件大小： | 0K |
| 描述： | IC AMP DIFF R-R LN LDIST 8SOIC |
| 标准包装： | 98 |
| 放大器类型： | 差分 |
| 电路数： | 1 |
| 输出类型： | 差分，满摆幅 |
| 转换速率： | 800 V/µs |
| -3db带宽： | 410MHz |
| 电流 - 输入偏压： | 2.25µA |
| 电压 - 输入偏移： | 150µV |
| 电流 - 电源： | 24.5mA |
| 电流 - 输出 / 通道： | 100mA |
| 电压 - 电源，单路/双路(±)： | 4.5 V ~ 12 V，±2.25 V ~ 6 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm Width）裸露焊盘 |
| 供应商设备封装： | 8-SOIC-EP |
| 包装： | 管件 |
| 产品目录页面： | 770 (CN2011-ZH PDF) |
AD8139
Rev. B | Page 19 of 24
APPLICATIONS
ESTIMATING NOISE, GAIN, AND BANDWIDTH
WITH MATCHED FEEDBACK NETWORKS
Estimating Output Noise Voltage
The total output noise is calculated as the root-sum-squared
total of several statistically independent sources. Because the
sources are statistically independent, the contributions of each
must be individually included in the root-sum-square calculation.
Table 6 lists recommended resistor values and estimates of
bandwidth and output differential voltage noise for various
closed-loop gains. For most applications, 1% resistors are
sufficient.
Table 6. Recommended Values of Gain-Setting Resistors and
Voltage Noise for Various Closed-Loop Gains
Gain
RG (Ω)
RF (Ω)
3 dB
Bandwidth (MHz)
Total Output
Noise (nV/√Hz)
1
200
400
5.8
2
200
400
160
9.3
5
200
1 k
53
19.7
10
200
2 k
26
37
The differential output voltage noise contains contributions
from the input voltage noise and input current noise of the
AD8139 as well as those from the external feedback networks.
The contribution from the input voltage noise spectral density
is computed as
+
=
G
F
n
R
v
Vo_n1
1
, or equivalently, vn/β
(7)
where vn is defined as the input-referred differential voltage
noise. This equation is the same as that of traditional op amps.
The contribution from the input current noise of each input is
computed as
Vo_n2 = in (RF)
(8)
where in is defined as the input noise current of one input.
Each input needs to be treated separately because the two
input currents are statistically independent processes.
The contribution from each RG is computed as
=
G
F
G
R
kTR
Vo_n3
4
(9)
This result can be intuitively viewed as the thermal noise of
each RG multiplied by the magnitude of the differential gain.
The contribution from each RF is computed as
Vo_n4 = √4kTRF
(10)
Voltage Gain
The behavior of the node voltages of the single-ended-to-
differential output topology can be deduced from the previous
one can write
F
ON
AP
G
AP
IP
R
V
R
V
=
(11)
+
=
G
F
G
OP
AP
AN
R
V
(12)
Solving the above two equations and setting VIP to Vi gives the
gain relationship for VO, dm/Vi.
i
G
F
dm
O,
ON
OP
V
R
V
=
(13)
An inverting configuration with the same gain magnitude can
be implemented by simply applying the input signal to VIN and
setting VIP = 0. For a balanced differential input, the gain from
VIN, dm to VO, dm is also equal to RF/RG, where VIN, dm = VIP VIN.
Feedback Factor Notation
When working with differential amplifiers, it is convenient to
introduce the feedback factor β, which is defined as
G
F
G
R
+
=
β
(14)
This notation is consistent with conventional feedback analysis
and is very useful, particularly when the two feedback loops are
not matched.
Input Common-Mode Voltage
The linear range of the VAN and VAP terminals extends to within
approximately 1 V of either supply rail. Because VAN and VAP are
essentially equal to each other, they are both equal to the input
common-mode voltage of the amplifier. Their range is indicated
in the Specifications tables as input common-mode range. The
can be expressed as
=
ACM
AP
AN
V
×
+
+
×
+
OCM
G
F
G
IN
IP
G
F
V
R
V
R
2
)
(
(15)
where VACM is the common-mode voltage present at the
amplifier input terminals.
Using the β notation, Equation 15 can be written as follows:
VACM = βVOCM + (1 β)VICM
(16)
or equivalently,
VACM = VICM + β(VOCM VICM)
(17)
where VICM is the common-mode voltage of the input signal,
that is, VICM = VIP + VIN/2.
相关PDF资料 |
PDF描述 |
|---|---|
| LT1206CT7#PBF | IC CURR FEEDBK AMP 250MA TO220-7 |
| 929835-01-16 | CONN HEADER .100 SNGL R/A 16POS |
| LT1206CR#PBF | IC CURRNT FEEDBCK AMP 250MA 7-DD |
| LTC2052IS#PBF | IC OPAMP ZERO-DRIFT QUAD 14SOIC |
| LTC2052CGN#PBF | IC OPAMP ZERO-DRIFT QUAD 16SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD8139ARDZ1 | 制造商:AD 制造商全称:Analog Devices 功能描述:Low Noise Rail-to-Rail Differential ADC Driver |
| AD8139ARDZ-REEL | 功能描述:IC AMP DIFF R-R LN LDIST 8SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:50 系列:- 放大器类型:J-FET 电路数:2 输出类型:- 转换速率:13 V/µs 增益带宽积:3MHz -3db带宽:- 电流 - 输入偏压:65pA 电压 - 输入偏移:3000µV 电流 - 电源:1.4mA 电流 - 输出 / 通道:- 电压 - 电源，单路/双路(±):7 V ~ 36 V，±3.5 V ~ 18 V 工作温度:-40°C ~ 85°C 安装类型:通孔 封装/外壳:8-DIP（0.300"，7.62mm） 供应商设备封装:8-PDIP 包装:管件 |
| AD8139ARDZ-REEL7 | 功能描述:IC AMP DIFF R-R LN LDIST 8SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:50 系列:- 放大器类型:J-FET 电路数:2 输出类型:- 转换速率:13 V/µs 增益带宽积:3MHz -3db带宽:- 电流 - 输入偏压:65pA 电压 - 输入偏移:3000µV 电流 - 电源:1.4mA 电流 - 输出 / 通道:- 电压 - 电源，单路/双路(±):7 V ~ 36 V，±3.5 V ~ 18 V 工作温度:-40°C ~ 85°C 安装类型:通孔 封装/外壳:8-DIP（0.300"，7.62mm） 供应商设备封装:8-PDIP 包装:管件 |
| AD8139AR-REEL | 制造商:Analog Devices 功能描述:ULTRA LOW NOISE FULLY DIFFERENTIAL ADC DRIVER - Tape and Reel |
| AD8139CP | 制造商:Analog Devices 功能描述: |
发布紧急采购，3分钟左右您将得到回复。