- 您现在的位置：买卖IC网 > PDF目录378276 > AD8152-EVAL (Analog Devices, Inc.) 34 x 34, 3.2 Gbps Asynchronous Digital Crosspoint Switch PDF资料下载
参数资料
| 型号： | AD8152-EVAL |
| 厂商： | Analog Devices, Inc. |
| 英文描述： | 34 x 34, 3.2 Gbps Asynchronous Digital Crosspoint Switch |
| 中文描述： | 34 × 34，3.2 Gbps的异步数字交叉点开关 |
| 文件页数： | 23/32页 |
| 文件大小： | 1351K |
| 代理商： | AD8152-EVAL |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页当前第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
REV. A
AD8152
–23–
ECL
DRIVER
TO 50
SCOPE
INPUTS
VCC
VTTO
VTTI
= –2V
VEE
= –2.5V
AD8152
P
P
N
N
IN
OUT
Figure 15. Evaluation Board ECL Driver Test Setup
Connections for Testing
The AD8152 evaluation board can be used under a variety of posi-
tive or negative supply configurations. Negative supply configurations,
as shown in Figure 15, allow the easiest hookup to test equip-
ment because inputs and outputs can be direct coupled. In a real
world application however, the negative supply configuration would
be difficult because control logic levels must be shifted negative.
Figure 16 is an example of a loop-through test setup using a posi-
tive supply. In this case, the test signal goes through the AD8152
twice. It is possible to loop through multiple times if desired, but
jitter will increase with number of loop-throughs. The first
input from the generator and the last output to a scope must be
ac-coupled. However, an AD8152 output driving its own input can
be direct-coupled. Direct coupling to the first AD8152 input is not
effective since generators usually want to see 50
W
to ground.
This would require VTTI to be attached to ground, causing
excessive power to be dissipated in the internal 50
W
input
termination resistors. Secondly, when the AD8152 output tries
to drive its own input with VTTI = 0 V and VTTO = 2.5 V, the
input will pull the output stage levels down enough to shut off
any signal toggling.
All ac coupling shown is actually done with a set of bias tees. If
desired, the bias tee can be used to monitor average dc voltage
levels at an input or output (depending on direction installed),
and it can also serve to change input dc levels. Make sure the
bias tees used in the setup have enough low frequency bandwidth
to pass long patterns and keep edge rates intact. The longer the
pattern, the more low frequency bandwidth is needed.
If ac coupling is desired on a user board, 0402 or 0603 sized
capacitors can be installed on microstrip lines. The biggest 0402
size, XR7 type usable is 0.01
m
F, which will work fine for short
patterns (PRBS 2
7
–1) and data rates down to 1.0 Gbps. For
long patterns a 0603 sized, XR7 type, 0.1
m
F should be used. To
decrease capacitive loading from the mounting area, clear out
planes underneath the coupling capacitor.
In Figure 16, 6 dB attenuators are placed before the AD8152
input ac-coupling or bias tees. This is because many generators
won’t go below 500 mV single-ended. The output pair of 6 dB
attenuators is present to protect the scope inputs and allow for
higher scale voltages per division. The eye diagram is usually
viewed differentially by using a simple P – N math function.
Cabling used in this setup must be matched. Mismatched cables
cause either a P or N signal to be falsely delayed. This delay can
show up as a change in the crossing point, from 50 percent in the
eye diagram. To accurately check cable matches, a TDR setup
is recommended.
PATTERN
GENERATOR
VCC
VTTO
2.5V
AD8152
P
P
N
N
IN01
OUT01
VTTI
P
N
P
N
IN02
OUT02
VEE
50
50
DATA OUT
DATA
OUT
TRIGGER OUT
TRIGGER IN
HIGH SPEED
SAMPLING
OSCILLOSCOPE
–6dB
–6dB
–6dB
–6dB
VCC = VTTI = VTTO = 2.5V, VEE = 0V,
SET = 16mA
RTI (REFERRED TO INPUT) A MPLITUDE = 400mV SINGLE–ENDED,
V
IN
HI = 2.7V (IN01), PRBS 2
–1, V
OH
= 2.5V,
V
= 2.1V,
AC-COUPLED IS FROM BIAS TEES,
PROGRAMMING: IN01 TO OUT02, IN02 TO OUT01.
Figure 16. Positive Supply Loop-Through Test Setup
相关PDF资料 |
PDF描述 |
|---|---|
| AD8152JBP | 34 x 34, 3.2 Gbps Asynchronous Digital Crosspoint Switch |
| AD82550A | Stereo Digital Audio Amplifier with Headphone Driver |
| AD82550A-CG | Stereo Digital Audio Amplifier with Headphone Driver |
| AD82551A | Stereo Digital Audio Amplifier with Headphone Driver |
| AD82551A-CG | Stereo Digital Audio Amplifier with Headphone Driver |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD8152JBP | 功能描述:IC CROSSPOINT SWIT 34X34 256BGA RoHS:否 类别:集成电路 (IC) >> 接口 - 模拟开关，多路复用器，多路分解器 系列:XStream™ 其它有关文件:STG4159 View All Specifications 标准包装:5,000 系列:- 功能:开关 电路:1 x SPDT 导通状态电阻:300 毫欧 电压电源:双电源 电压 - 电源，单路/双路(±):±1.65 V ~ 4.8 V 电流 - 电源:50nA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:7-WFBGA，FCBGA 供应商设备封装:7-覆晶 包装:带卷 (TR) |
| AD8152JBPZ | 功能描述:IC CROSSPOINT SWIT 34X34 256BGA RoHS:是 类别:集成电路 (IC) >> 接口 - 模拟开关，多路复用器，多路分解器 系列:XStream™ 应用说明:Ultrasound Imaging Systems Application Note 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:250 系列:- 功能:开关 电路:单刀单掷 导通状态电阻:48 欧姆 电压电源:单电源 电压 - 电源，单路/双路(±):2.7 V ~ 5.5 V 电流 - 电源:5µA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:48-LQFP 供应商设备封装:48-LQFP（7x7） 包装:托盘 |
| AD8153 | 制造商:AD 制造商全称:Analog Devices 功能描述:3.2 Gbps Single Buffered Mux/Demux Switch |
| AD8153_07 | 制造商:AD 制造商全称:Analog Devices 功能描述:3.2 Gbps Single Buffered Mux/Demux Switch |
| AD8153ACPZ | 功能描述:IC SW MUX/DEMUX SGL BUFF 32LFCSP RoHS:是 类别:集成电路 (IC) >> 接口 - 专用 系列:XStream™ 特色产品:NXP - I2C Interface 标准包装:1 系列:- 应用:2 通道 I²C 多路复用器 接口:I²C，SM 总线 电源电压:2.3 V ~ 5.5 V 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:剪切带 (CT) 安装类型:表面贴装 产品目录页面:825 (CN2011-ZH PDF) 其它名称:568-1854-1 |
发布紧急采购，3分钟左右您将得到回复。