参数资料
型号: AD8155ACPZ-R7
厂商: Analog Devices Inc
文件页数: 8/36页
文件大小: 0K
描述: IC MUX/DEMUX DUAL BUFFER 64LFCSP
标准包装: 750
系列: XStream™
功能: 多路复用器/多路分解器
电路: 2 x 2:1
电压电源: 单电源
电压 - 电源,单路/双路(±): 1.6 V ~ 3.6 V
电流 - 电源: 735mA
工作温度: -40°C ~ 85°C
安装类型: 表面贴装
封装/外壳: 64-VFQFN 裸露焊盘,CSP
供应商设备封装: 64-LFCSP-VQ(9x9)
包装: 带卷 (TR)
AD8155
Rev. 0 | Page 16 of 36
Table 6. Features Available Through Toggle Pin or Serial Control
Feature
Pin Control
Serial Control
Switch Features
BICAST
One pin
One bit
A/B Lane Select
Two pins
Two bits
Loopback
Three pins
Three bits
Rx Features
EQ Levels
Two settings
10 settings
N/P Swap
Not available
Available
Squelch
Enabled
Three bits
Tx Features
Programmable Output Levels
±400 mV diff fixed1
±200 mV diff/±300 mV diff/±400 mV diff/±600 mV diff
PE Levels
Two settings
>7 settings
1 ±400 mV diff indicates a 400 mV amplitude signal measured between two differential nodes. The voltage swing at differential I/O pins is described in this data sheet
both in terms of the differentially measured voltage range (±400 mV diff, for example) and in terms of peak-to-peak differential swing, denoted as mV p-p diff. An
output level setting of ±400 mV diff delivers a differential peak-to-peak output voltage of 800 mV p-p diff.
THE SWITCH
(MUX/DEMUX/UNICAST/BICAST/LOOPBACK)
The mux and demux functions of the AD8155 can be controlled
either with the toggle pins or through the register map. The
multiplexer path switches received data from Input Port A or
Input Port B to Output Port C. The SEL[1:0] pins allow switching
lanes independently. The demultiplexer path switches received
data from Input Port C to Output Port A, Output Port B, or (if
bicast mode is enabled) to both Output Port A and Output Port B.
Table 7. Port Selection and Configuration with All
Loopbacks Disabled
BICAST
SELx
Output
Port A
Output
Port B
Output
Port C
0
Ix_C[1:0]
Idle
Ix_A[1:0]
0
1
Idle
Ix_C[1:0]
Ix_B[1:0]
1
0
Ix_C[1:0]
Ix_A[1:0]
1
Ix_C[1:0]
Ix_B[1:0]
When the device is in unicast mode, the output lanes on either
Port A or Port B are in an idle state. In the idle state, the
transmitter output current is set to 0, and the P and N sides of
the lane are pulled up to the output termination voltage through
the on-chip termination resistors. To save power, the unused
receiver automatically disables.
The AD8155 supports port-level loopback, illustrated in Figure 36.
The loopback control pins override the lane select (SEL[1:0])
and bicast control (BICAST) pin settings at the port level. In serial
control mode, Bits [6:4] of Register 0x01 control loopback and
are equivalent to asserting Pin LB_A, Pin LB_B, and Pin LB_C.
Table 8 summarizes the different loopback configurations.
The loopback feature is useful for system debug, self-test, and
initialization, allowing system ASICs to compare Tx and Rx
data sent over a single bidirectional link. Loopback can also be
used to configure the device as a two- to six-lane receive
equalizer or backplane redriver.
相关PDF资料
PDF描述
AD7512DIKP IC SWITCH DUAL SPDT 20PLCC
ADG526AKR IC MULTIPLEXER 16X1 28SOIC
ADG506AKNZ IC MULTIPLEXER 16X1 28DIP
ADG506AKN IC MULTIPLEXER 16X1 28DIP
SY55859LMG TR IC CROSSPOINT SWITCH DUAL 32MLF
相关代理商/技术参数
参数描述
AD8155-EVALZ 制造商:AD 制造商全称:Analog Devices 功能描述:6.5 Gbps Dual Buffer Mux/Demux
AD8155XCPZ 制造商:Analog Devices 功能描述:
AD8156 制造商:AD 制造商全称:Analog Devices 功能描述:6.25 Gbps 4】4 Digital Crosspoint Switch with EQ
AD8156ABCZ 功能描述:IC SWITCH XPT 4X4 W/EQ 49CSPBGA RoHS:是 类别:集成电路 (IC) >> 接口 - 专用 系列:XStream™ 特色产品:NXP - I2C Interface 标准包装:1 系列:- 应用:2 通道 I²C 多路复用器 接口:I²C,SM 总线 电源电压:2.3 V ~ 5.5 V 封装/外壳:16-TSSOP(0.173",4.40mm 宽) 供应商设备封装:16-TSSOP 包装:剪切带 (CT) 安装类型:表面贴装 产品目录页面:825 (CN2011-ZH PDF) 其它名称:568-1854-1
AD8156-EVALZ 制造商:AD 制造商全称:Analog Devices 功能描述:6.25 Gbps 4】4 Digital Crosspoint Switch with EQ