- 您现在的位置：买卖IC网 > PDF目录373940 > AD8202_05 (Analog Devices, Inc.) High Common-Mode Voltage, Single-Supply Difference Amplifier PDF资料下载
参数资料
| 型号： | AD8202_05 |
| 厂商： | Analog Devices, Inc. |
| 元件分类： | 运动控制电子 |
| 英文描述： | High Common-Mode Voltage, Single-Supply Difference Amplifier |
| 中文描述： | 高共模电压，单电源差分放大器 |
| 文件页数： | 14/20页 |
| 文件大小： | 248K |
| 代理商： | AD8202_05 |
AD8202
APPLICATIONS
The AD8202 difference amplifier is intended for applications that
require extracting a small differential signal in the presence of
large common-mode voltages. The differential input resistance
is nominally 325 kΩ, and the device can tolerate common-mode
voltages higher than the supply voltage and lower than ground.
Rev. D | Page 14 of 20
The open collector output stage sources current to within
20 mV of ground and to within 200 mV of V
S
.
CURRENT SENSING
High Line, High Current Sensing
Basic automotive applications using the large common-mode
range are shown in Figure 2 and Figure 3. The capability of the
device to operate as an amplifier in primary battery supply
circuits is shown in Figure 2; Figure 3 illustrates the ability
of the device to withstand voltages below system ground.
Low Current Sensing
The AD8202 is also used in low current sensing applications,
such as the 4 to 20 mA current loop shown in Figure 42. In such
applications, the relatively large shunt resistor can degrade the
common-mode rejection. Adding a resistor of equal value on the
low impedance side of the input corrects for this error.
5V
OUTPUT
10
Ω
1%
10
Ω
1%
NC = NO CONNECT
+
GND
NC
–IN
+IN
A1
+V
S
A2
OUT
AD8202
0
Figure 42. 4 to 20 mA Current Loop Receiver
GAIN ADJUSTMENT
The default gain of the preamplifier and buffer are ×10 and ×2,
respectively, resulting in a composite gain of ×20. With the
addition of external resistor(s) or trimmer(s), the gain can be
lowered, raised, or finely calibrated.
Gains Less than 20
Because the preamplifier has an output resistance of 100 kΩ,
an external resistor connected from Pin 3 and Pin 4 to GND
decreases the gain by a factor R
EXT
/(100 kΩ + R
EXT
) as shown
in Figure 43.
10k
Ω
10k
Ω
100k
Ω
A2
A1
GND
–IN
OUT
+V
S
NC
+IN
AD8202
OUT
+V
S
R
EXT
V
CM
V
DIFF
2
GAIN =
20R
EXT
R
EXT
+ 100k
Ω
R
EXT
= 100k
Ω
GAIN
20 – GAIN
V
DIFF
2
NC = NO CONNECT
0
Figure 43. Adjusting for Gains Less than 20
The overall bandwidth is unaffected by changes in gain by using
this method, although there may be a small offset voltage due
to the imbalance in source resistances at the input to the buffer.
This can often be ignored, but if desired, it can be nulled by
inserting a resistor equal to 100 kΩ minus the parallel sum of R
EXT
and 100 kΩ, in series with Pin 4. For example, with R
EXT
= 100 kΩ
(yielding a composite gain of ×10), the optional offset nulling
resistor is 50 kΩ.
Gains Greater Than 20
Connecting a resistor from the output of the buffer amplifier
to its noninverting input, as shown in Figure 44, increases the
gain. The gain is multiplied by the factor R
EXT
/(R
EXT
100 kΩ);
for example, the gain is doubled for R
EXT
= 200 kΩ. Overall
gains as high as 50 are achievable in this way. The accuracy of
the gain becomes critically dependent on the resistor value at
high gains. Also, the effective input offset voltage at Pin 1 and
Pin 8 (about six times the actual offset of A1) limits the part’s
use in high gain, dc-coupled applications.
10k
Ω
10k
Ω
100k
Ω
A2
A1
GND
–IN
OUT
+V
S
NC
+IN
AD8202
OUT
+V
S
R
EXT
V
CM
V
DIFF
2
GAIN =
20R
EXT
R
EXT
– 100k
Ω
R
EXT
= 100k
Ω
GAIN
GAIN – 20
V
DIFF
2
NC = NO CONNECT
0
Figure 44. Adjusting for Gains > 20
相关PDF资料 |
PDF描述 |
|---|---|
| AD8202YRMZ | High Common-Mode Voltage, Single-Supply Difference Amplifier |
| AD8202YRMZ-R7 | High Common-Mode Voltage, Single-Supply Difference Amplifier |
| AD8202YRMZ-RL | High Common-Mode Voltage, Single-Supply Difference Amplifier |
| AD8202YRZ | High Common-Mode Voltage, Single-Supply Difference Amplifier |
| AD8203 | High Common-Mode Voltage, Single-Supply Difference Amplifier |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD8202-W | 功能描述:Differential Amplifier 1 Circuit Die 制造商:analog devices inc. 系列:- 包装:散装 零件状态:上次购买时间 放大器类型:差分 电路数:1 输出类型:- 压摆率:0.28 V/μs 增益带宽积:50kHz -3db 带宽:- 电流 - 输入偏置:40nA 电压 - 输入失调:2mV 电流 - 电源:250μA 电流 - 输出/通道:- 电压 - 电源，单/双（±）:3.5 V ~ 12 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:模具 供应商器件封装:模具 标准包装:1 |
| AD8202WYC-P3 | 功能描述:Differential Amplifier 1 Circuit Die 制造商:analog devices inc. 系列:- 包装:散装 零件状态:上次购买时间 放大器类型:差分 电路数:1 输出类型:- 压摆率:0.28 V/μs 增益带宽积:50kHz -3db 带宽:- 电流 - 输入偏置:40nA 电压 - 输入失调:2mV 电流 - 电源:250μA 电流 - 输出/通道:- 电压 - 电源，单/双（±）:3.5 V ~ 12 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:模具 供应商器件封装:模具 标准包装:1 |
| AD8202WYC-P7 | 制造商:Analog Devices 功能描述:HIGH COMMON-MODE VOLTAGE, SINGLE-SUPPLY DIFFERENCE AMPLIFIER - Gel-pak, waffle pack, wafer, diced wafer on film |
| AD8202WYRMZ | 功能描述:IC AMP DIFF 50KHZ 8MSOP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:100 系列:- 放大器类型:通用 电路数:1 输出类型:- 转换速率:0.2 V/µs 增益带宽积:- -3db带宽:- 电流 - 输入偏压:100pA 电压 - 输入偏移:30µV 电流 - 电源:380µA 电流 - 输出 / 通道:- 电压 - 电源，单路/双路(±):±2 V ~ 18 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SO 包装:管件 |
| AD8202WYRMZ-RL | 功能描述:IC AMP DIFF 50KHZ 8MSOP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:1,000 系列:- 放大器类型:电压反馈 电路数:4 输出类型:满摆幅 转换速率:33 V/µs 增益带宽积:20MHz -3db带宽:30MHz 电流 - 输入偏压:2nA 电压 - 输入偏移:3000µV 电流 - 电源:2.5mA 电流 - 输出 / 通道:30mA 电压 - 电源，单路/双路(±):4.5 V ~ 16.5 V，±2.25 V ~ 8.25 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SOIC 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。