- 您现在的位置：买卖IC网 > PDF目录6074 > AD8220ARMZ-R7 (Analog Devices Inc)IC AMP INST JFET R-R 15MA 8MSOP PDF资料下载
参数资料
| 型号： | AD8220ARMZ-R7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 13/28页 |
| 文件大小： | 0K |
| 描述： | IC AMP INST JFET R-R 15MA 8MSOP |
| 产品培训模块： | Power Line Monitoring Top Five Instrumentation Amplifier Problems Instrumentation Amplifiers Performance |
| 设计资源： | Fully Isolated Input Module Based on AD7793, ADuM5401, and a High Performance In-Amp (CN0067) |
| 标准包装： | 1 |
| 放大器类型： | 仪表 |
| 电路数： | 1 |
| 输出类型： | 满摆幅 |
| 转换速率： | 2 V/µs |
| -3db带宽： | 1.5MHz |
| 电流 - 输入偏压： | 25pA |
| 电压 - 输入偏移： | 250µV |
| 电流 - 电源： | 750µA |
| 电流 - 输出 / 通道： | 15mA |
| 电压 - 电源，单路/双路(±)： | 4.5 V ~ 36 V，±2.25 V ~ 18 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-MSOP |
| 包装： | 标准包装 |
| 产品目录页面： | 771 (CN2011-ZH PDF) |
| 其它名称： | AD8220ARMZ-R7DKR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
AD8220
Rev. B | Page 20 of 28
GAIN SELECTION
Placing a resistor across the RG terminals sets the AD8220 gain,
which can be calculated by referring to Table 5 or by using the
gain equation
1
kΩ
4
.
49
G
RG
Table 5. Gains Achieved Using 1% Resistors
1% Standard Table Value of RG (Ω)
Calculated Gain
49.9 k
1.990
12.4 k
4.984
5.49 k
9.998
2.61 k
19.93
1.00 k
50.40
499
100.0
249
199.4
100
495.0
49.9
991.0
The AD8220 defaults to G = 1 when no gain resistor is used.
Gain accuracy is determined by the absolute tolerance of RG.
The TC of the external gain resistor increases the gain drift of
the instrumentation amplifier. Gain error and gain drift are kept
to a minimum when the gain resistor is not used.
LAYOUT
Careful board layout maximizes system performance. In
applications that need to take advantage of the low input bias
current of the AD8220, avoid placing metal under the input path
to minimize leakage current. To maintain high CMRR over
frequency, lay out the input traces symmetrically and lay out the
traces of the RG resistor symmetrically. Ensure that the traces
maintain resistive and capacitive balance; this holds for additional
PCB metal layers under the input and RG pins. Traces from the
gain setting resistor to the RG pins should be kept as short as
possible to minimize parasitic inductance. An example layout is
shown in Figure 57 and Figure 58. To ensure the most accurate
output, the trace from the REF pin should either be connected to
the AD8220 local ground (see Figure 59) or connected to a
voltage that is referenced to the AD8220 local ground.
Common-Mode Rejection Ratio (CMRR)
The AD8220 has high CMRR over frequency giving it greater
immunity to disturbances, such as line noise and its associated
harmonics, in contrast to typical in-amps whose CMRR falls off
around 200 Hz. These in-amps often need common-mode
filters at the inputs to compensate for this shortcoming. The
AD8220 is able to reject CMRR over a greater frequency range,
reducing the need for input common-mode filtering.
A well-implemented layout helps to maintain the high CMRR
over frequency of the AD8220. Input source impedance and
capacitance should be closely matched. In addition, source
resistance and capacitance should be placed as close to the
inputs as possible.
Grounding
The output voltage of the AD8220 is developed with respect to
the potential on the reference terminal. Care should be taken to
tie REF to the appropriate local ground (see Figure 59).
In mixed-signal environments, low level analog signals need to
be isolated from the noisy digital environment. Many ADCs
have separate analog and digital ground pins. Although it is
convenient to tie both grounds to a single ground plane, the
current traveling through the ground wires and PC board can
cause a large error. Therefore, separate analog and digital
ground returns should be used to minimize the current flow
from sensitive points to the system ground.
03579-
101
Figure 57. Example Layout—Top Layer of the AD8220 Evaluation Board
03579-
102
Figure 58. Example Layout—Bottom Layer of the AD8220 Evaluation Board
相关PDF资料 |
PDF描述 |
|---|---|
| KD1205PFB1 H | FAN 12VDC 50X10.5MM 1.6W 11.4CFM |
| KD1205PFB3 H | FAN 12VDC 50X10.5MM .8W 8.0CFM |
| AD8651ARZ | IC OPAMP VF CMOS 50MHZ LN 8SOIC |
| 0324.125HXP | FUSE CERM 250V FST AXL 3AB .125A |
| AD8619ARUZ | IC OPAMP GP R-R CMOS LN 14TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD8220ARMZ-RL | 功能描述:IC AMP INST JFET R-R 15MA 8MSOP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:100 系列:- 放大器类型:通用 电路数:1 输出类型:- 转换速率:0.2 V/µs 增益带宽积:- -3db带宽:- 电流 - 输入偏压:100pA 电压 - 输入偏移:30µV 电流 - 电源:380µA 电流 - 输出 / 通道:- 电压 - 电源，单路/双路(±):±2 V ~ 18 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SO 包装:管件 |
| AD8220BRMZ | 功能描述:IC AMP INST JFET R-R 15MA 8MSOP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:2,500 系列:- 放大器类型:通用 电路数:4 输出类型:- 转换速率:0.6 V/µs 增益带宽积:1MHz -3db带宽:- 电流 - 输入偏压:45nA 电压 - 输入偏移:2000µV 电流 - 电源:1.4mA 电流 - 输出 / 通道:40mA 电压 - 电源，单路/双路(±):3 V ~ 32 V，±1.5 V ~ 16 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:14-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:14-TSSOP 包装:带卷 (TR) 其它名称:LM324ADTBR2G-NDLM324ADTBR2GOSTR |
| AD8220BRMZ-R7 | 功能描述:IC AMP INST JFET R-R 15MA 8MSOP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:50 系列:- 放大器类型:J-FET 电路数:2 输出类型:- 转换速率:13 V/µs 增益带宽积:3MHz -3db带宽:- 电流 - 输入偏压:65pA 电压 - 输入偏移:3000µV 电流 - 电源:1.4mA 电流 - 输出 / 通道:- 电压 - 电源，单路/双路(±):7 V ~ 36 V，±3.5 V ~ 18 V 工作温度:-40°C ~ 85°C 安装类型:通孔 封装/外壳:8-DIP（0.300"，7.62mm） 供应商设备封装:8-PDIP 包装:管件 |
| AD8220BRMZ-RL | 功能描述:IC AMP INST JFET R-R 15MA 8MSOP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:50 系列:- 放大器类型:J-FET 电路数:2 输出类型:- 转换速率:13 V/µs 增益带宽积:3MHz -3db带宽:- 电流 - 输入偏压:65pA 电压 - 输入偏移:3000µV 电流 - 电源:1.4mA 电流 - 输出 / 通道:- 电压 - 电源，单路/双路(±):7 V ~ 36 V，±3.5 V ~ 18 V 工作温度:-40°C ~ 85°C 安装类型:通孔 封装/外壳:8-DIP（0.300"，7.62mm） 供应商设备封装:8-PDIP 包装:管件 |
| AD8220-EVAL | 制造商:AD 制造商全称:Analog Devices 功能描述:JFET Input Instrumentation Amplifier with Rail-to-Rail Output in MSOP Package |
发布紧急采购，3分钟左右您将得到回复。