参数资料
| 型号： | AD828ARZ-REEL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 2/12页 |
| 文件大小： | 0K |
| 描述： | IC VIDEO OPAMP DUAL LP 8-SOIC |
| 标准包装： | 2,500 |
| 应用： | 电压反馈 |
| 电路数： | 2 |
| -3db带宽： | 130MHz |
| 转换速率： | 450 V/µs |
| 电流 - 电源： | 14mA |
| 电流 - 输出 / 通道： | 50mA |
| 电压 - 电源，单路/双路(±)： | 5 V ~ 36 V，±2.5 V ~ 18 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 带卷 (TR) |
REV. C
–10–
AD828
THEORY OF OPERATION
The AD828 is a low cost, dual video operational amplifier
designed to excel in high performance, high output current
video applications.
The AD828 consists of a degenerated NPN differential pair
driving matched PNPs in a folded-cascade gain stage (Figure 4).
The output buffer stage employs emitter followers in a class AB
amplifier that delivers the necessary current to the load while
maintaining low levels of distortion.
The AD828 will drive terminated cables and capacitive loads of
10 pF or less. As the closed-loop gain is increased, the AD828
will drive heavier cap loads without oscillating.
–IN
+IN
OUTPUT
+VS
–VS
Figure 4. Simplified Schematic
INPUT CONSIDERATIONS
An input protection resistor (RIN in TPC 31) is required in circuits
where the input to the AD828 will be subjected to transient or
continuous overload voltages exceeding the
±6 V maximum dif-
ferential limit. This resistor provides protection for the input
transistors by limiting their maximum base current.
For high performance circuits, the “balancing” resistor should be
used to reduce the offset errors caused by bias current flowing
through the input and feedback resistors. The balancing resistor
equals the parallel combination of RIN and RF and thus provides
a matched impedance at each input terminal. The offset voltage
error will then be reduced by more than an order of magnitude.
APPLYING THE AD828
The AD828 is a breakthrough dual amp that delivers precision and
speed at low cost with low power consumption. The AD828 offers
excellent static and dynamic matching characteristics, combined
with the ability to drive heavy resistive loads.
As with all high frequency circuits, care should be taken to main-
tain overall device performance as well as their matching. The
following items are presented as general design considerations.
Circuit Board Layout
Input and output runs should be laid out so as to physically
isolate them from remaining runs. In addition, the feedback
resistor of each amplifier should be placed away from the feed-
back resistor of the other amplifier, since this greatly reduces
interamp coupling.
Choosing Feedback and Gain Resistors
To prevent the stray capacitance present at each amplifier’s
summing junction from limiting its performance, the feedback
resistors should be
≤ 1 k. Since the summing junction capaci-
tance may cause peaking, a small capacitor (1 pF to 5 pF) may
be paralleled with RF to neutralize this effect. Finally, sockets
should be avoided, because of their tendency to increase interlead
capacitance.
Power Supply Bypassing
Proper power supply decoupling is critical to preserve the
integrity of high frequency signals. In carefully laid out designs,
decoupling capacitors should be placed in close proximity to
the supply pins, while their lead lengths should be kept to a
minimum. These measures greatly reduce undesired inductive
effects on the amplifier’s response.
Though two 0.1
F capacitors will typically be effective in
decoupling the supplies, several capacitors of different values
can be paralleled to cover a wider frequency range.
PARALLEL AMPS PROVIDE 100 mA TO LOAD
By taking advantage of the superior matching characteristics of the
AD828, enhanced performance can easily be achieved by employ-
ing the circuit in Figure 5. Here, two identical cells are paralleled
to obtain even higher load driving capability than that of a single
amplifier (100 mA min guaranteed). R1 and R2 are included to
limit current flow between amplifier outputs that would arise in
the presence of any residual mismatch.
2
+VS
VIN
VOUT
3
8
1k
R2
5
–VS
RL
1/2
AD828
1/2
AD828
1 F
0.1 F
7
5
6
1
1 F
0.1 F
4
R1
5
1k
Figure 5. Parallel Amp Configuration
相关PDF资料 |
PDF描述 |
|---|---|
| VE-J5P-MZ-B1 | CONVERTER MOD DC/DC 13.8V 25W |
| VE-B3P-MU-F1 | CONVERTER MOD DC/DC 13.8V 200W |
| VE-J51-MZ-B1 | CONVERTER MOD DC/DC 12V 25W |
| VE-J4D-MZ-B1 | CONVERTER MOD DC/DC 85V 25W |
| VE-J44-MZ-B1 | CONVERTER MOD DC/DC 48V 25W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD828ARZ-REEL7 | 功能描述:IC VIDEO OPAMP DUAL LP 8-SOIC RoHS:是 类别:集成电路 (IC) >> 线性 - 放大器 - 视频放大器和频缓冲器 系列:- 标准包装:1,000 系列:- 应用:驱动器 输出类型:差分 电路数:3 -3db带宽:350MHz 转换速率:1000 V/µs 电流 - 电源:14.5mA 电流 - 输出 / 通道:60mA 电压 - 电源，单路/双路(±):5 V ~ 12 V，±2.5 V ~ 6 V 安装类型:表面贴装 封装/外壳:20-VFQFN 裸露焊盘 供应商设备封装:20-QFN 裸露焊盘（4x4） 包装:带卷 (TR) |
| AD829 | 制造商:AD 制造商全称:Analog Devices 功能描述:High Speed, Low Noise Video Op Amp |
| AD829_04 | 制造商:AD 制造商全称:Analog Devices 功能描述:High Speed, Low Noise Video Op Amp |
| AD829_11 | 制造商:AD 制造商全称:Analog Devices 功能描述:High Speed, Low Noise Video Op Amp |
| AD8290 | 制造商:AD 制造商全称:Analog Devices 功能描述:Low Noise, Low Gain Drift, G = 2000 Instrumentation Amplifier |
发布紧急采购，3分钟左右您将得到回复。