参数资料
| 型号： | AD8336ACPZ-WP |
| 厂商： | Analog Devices Inc |
| 文件页数： | 15/28页 |
| 文件大小： | 0K |
| 描述： | IC VGA GP SGL-ENDED 16-LFCSP |
| 标准包装： | 64 |
| 系列： | X-AMP® |
| 类型： | 可变增益放大器 |
| 应用： | 信号处理 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-VQFN 裸露焊盘，CSP |
| 供应商设备封装： | 16-LFCSP-VQ EP（4x4） |
| 包装： | 托盘 - 晶粒 |
| 配用： | AD8336-EVALZ-ND - BOARD EVALUATION FOR AD8336 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
AD8336
Rev. C | Page 22 of 28
APPLICATIONS INFORMATION
AMPLIFIER CONFIGURATION
The AD8336 amplifiers can be configured in various options. In
addition to the 60 dB gain range variable gain stage, an uncommit-
ted voltage gain amplifier is available to the user as a preamplifier.
The preamplifier connections are separate to enable noninverting
or inverting gain configurations or the use of interstage filtering.
The AD8336 can be used as a cascade connected VGA with pre-
amp input, as a standalone VGA, or as a standalone preamplifier.
This section describes some of the possible applications.
VOUT
VGAI
2
13
PRAO
1
GNEG
3
AD8336
VCOM
VPOS
GPOS
9
8
34dB
PrA
PWRA
ATTENUATOR
–60dB TO 0dB
12
GAIN CONTROL
INTERFACE
11
INPP 4
5
INPN
+
–
BIAS
10
VNEG
0
6228-
07
9
Figure 79. Application Block Diagram
PREAMPLIFIER
While observing just a few constraints, the uncommitted voltage
feedback preamplifier of the AD8336 can be connected in a
variety of standard high frequency op amp configurations. The
amplifier is optimized for a gain of 4× (12 dB) and has a gain
bandwidth product of 600 MHz. At a gain of 4×, the bandwidth
is 150 MHz. The preamplifier gain can be adjusted to a minimum
gain of 2×; however, there will be a small peak in the response at
high frequencies. At higher preamplifier gains, the bandwidth
diminishes proportionally in conformance to the classical voltage
gain amplifier GBW relationship.
While setting the overall gain of the AD8336, the user needs
to consider the input-referred offset voltage of the preamplifier.
Although the offset of the attenuator and postamplifier are almost
negligible, the preamplifier offset voltage, if uncorrected, is
increased by the combined gain of the preamplifier and post-
amplifier. Therefore, for a maximum gain of 60 dB, an input
offset voltage of only 200 μV results in an error of 200 mV at
the output.
Circuit Configuration for Noninverting Gain
The noninverting configuration is shown in Figure 80. The
preamp gain is described by the classical op amp gain equation:
1
2
+
=
FB
R
Gain
The practical gain limits for this amplifier are 6 dB to 26 dB.
The gain bandwidth product is about 600 MHz, so at 150 MHz,
the maximum achievable gain is 12 dB (4×). The minimum gain
is established internally by fixed loop compensation and is 6 dB
(2×). This amplifier is not designed for unity-gain operation.
Table 5 shows the gain and bandwidth for the noninverting gain
configuration.
PRAO
34dB
AD8336
PREAMPLIFIER
INPP
–60dB TO 0dB
4
5
INPN
9
GAIN = 12dB
RFB1
100
VGAI
13
VPOS
VNEG
10
VOUT
1
06
22
8-
0
8
0
RFB2
301
+5V
–5V
PWRA
2
3
VCOM
8
Figure 80. Circuit Configuration for Noninverting Gain
The preamplifier output reliably sources and sinks currents up
to 50 mA. When using ±5 V power supplies, the suggested sum
of the output resistor values is 400 Ω total for the optimal trade-
off between distortion and noise. Much of the low gain value
device characterization was performed with resistor values of
301 Ω and 100 Ω, resulting in a preamplifier gain of 12 dB (4×).
With supply voltages between ±5 V and ±12 V, the sum of the
output resistance should be increased accordingly; a total
resistance of 1 kΩ is recommended. Larger resistance values,
subject to a trade-off in higher noise performance, can be used
if circuit power and load driving is an issue. When considering
the total power dissipation, remember that the input ladder
resistance of the VGA is part of the preamp load.
Table 5. Gain and Bandwidth for Noninverting Preamplifier
Configuration
Preamp Gain
Preamp BW
(MHz)
Composite
Gain (dB)
Numerical
dB
4×
12
150
14 to +46
8×
18
60
8 to +52
16×
24
30
2 to +58
20×
26
25
0 to +60
相关PDF资料 |
PDF描述 |
|---|---|
| AD8337BCPZ-REEL7 | IC AMP VGA LOW NOISE 8-LFCSP |
| AD834AQ | IC MULTIPLIER 4-QUADRANT 8-CDIP |
| AD835AR | IC MULTIPLIER 4-QUADRANT 8-SOIC |
| AD8465WBCPZ-R7 | IC COMPARATOR LVDS R-R 12LFCSP |
| AD8468WBKSZ-R7 | IC COMPARATOR TTL/CMOS SC70-6 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD8336-EVALZ | 功能描述:BOARD EVALUATION FOR AD8336 RoHS:是 类别:编程器，开发系统 >> 评估板 - 运算放大器 系列:X-AMP® 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- |
| AD8337 | 制造商:AD 制造商全称:Analog Devices 功能描述:General-Purpose, Low Cost, DC-Coupled VGA |
| AD8337_07 | 制造商:AD 制造商全称:Analog Devices 功能描述:General-Purpose, Low Cost, DC-Coupled VGA |
| AD8337BCPZ | 制造商:Analog Devices 功能描述:VGA DC COUPLED SMD LFCSP-8 8337 制造商:Analog Devices 功能描述:VGA, DC COUPLED, SMD, LFCSP-8, 8337 |
| AD8337BCPZ-R2 | 功能描述:IC AMP VGA LOW NOISE 8-LFCSP RoHS:是 类别:集成电路 (IC) >> 线性 - 放大器 - 专用 系列:X-AMP® 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:60 系列:- 类型:可变增益放大器 应用:CATV 安装类型:表面贴装 封装/外壳:20-WQFN 裸露焊盘 供应商设备封装:20-TQFN-EP（5x5） 包装:托盘 |
发布紧急采购，3分钟左右您将得到回复。