- 您现在的位置：买卖IC网 > PDF目录373944 > AD8348 (Analog Devices, Inc.) 50-1000 MHz Quadrature Demodulator PDF资料下载
参数资料
| 型号： | AD8348 |
| 厂商： | Analog Devices, Inc. |
| 英文描述： | 50-1000 MHz Quadrature Demodulator |
| 中文描述： | 50-1000兆赫正交解调器 |
| 文件页数： | 12/13页 |
| 文件大小： | 778K |
| 代理商： | AD8348 |
PRELIMINARY TECHNICAL DATA
Rev. PrF 2/11/03
- 12 -
Table I Evaluation Board Configuration Options
Function
Power Supply and Ground Vector Pins
Device Enable:
Place SW11 in the ENBL position to connect the ENBL
pin to +Vs. Place in the DENBL position to disable the device by
grounding the pin ENBL through a 50 Ohm pull down resistor. The
device may also be enabled via an external voltage applied to ENBL or
VENB.
Gain Control Selection:
With SW13 in the POT position the gain of the
VGA can be set using the potentiometer R15. With SW13 in the EXT
position the VGA gain can be set by an external voltage to SMA connector
VGIN. For VGA operation the VGA must first be enabled by setting
SW12 to the IF position.
VGA Enable Selection:
With SW12 in the IF position, the ENVG pin is
connected to +Vs and the VGA is enabled. The IF input should be used
when SW12 is in the IF position. With SW12 in the MX position the
ENVG pin is grounded and the VGA is disabled. The MX inputs should
be used when SW12 is in the MX position.
IF Input:
The single-ended IF signal should be connected to this SMA
connector. R31 and R32 form a L-pad that presents a 50 Ohm termination
to the input.
Mixer Inputs:
These inputs can be configured for either differential or
single-ended operation. The default is single-ended operation with T41
and R42 installed. In single-ended mode the input is applied to the 50
Ohm SMA connector MXIP. For differential drive, T41 should be
removed along with resistor R42. DC blocking capacitors (C42, C43)
should be installed in place of T41. This will present a nominal
differential impedance of 200 Ohms (100 Ohms each side). The
differential inputs should then be fed into SMA connectors MXIP and
MXIN.
Baseband Amplifier Output Bias
: Installing LK11 connects VREF to
VCMO. This sets the bias level on the baseband amplifiers to V
REF
which
is equal to approximately 1V. Alternatively, with LK11 removed, the bias
level of the baseband amplifiers can be set by applying an external voltage
to the VCMO testpoint.
Baseband Amplifier Outputs and Output Filter:
Additional low-pass
filtering can be provided at the baseband output with these filters.
Mixer Output DC Blocking Capacitors:
The mixer outputs are biased to
VCMO. To prevent damage to test equipment that cannot tolerate DC
biases, C10 is provided to block the DC component, thus protecting the
test equipment.
Baseband Filter:
These components are provided for baseband filtering
between the mixer outputs and the baseband amplifier inputs. The
baseband amplifier input impedance is high and the filter termination
impedance is set by R2. See Table II below for jumper settings.
Offset Compensation Loop Disable:
Installing these jumpers will
disable the offset compensation loop for the corresponding channel.
Component
+Vs, GND
SW11, ENBL
Default Condition
Not Applicable
SW11 = ENBL
SW13, R15,
VGIN
SW2 = POT
SW12
SW12 = IF
IFIP, R31, R32
R31 = 57.6 Ohms
R32 = 174 Ohms
MXIP, MXIN
T41, R42
C42, C43
T41 = ETC4-1-2
R42 = 0 Ohms
LK11, VCMO
LK11 Installed
C8, C9, R4, R5
(I and Q)
C10 (I and Q)
R4, R5 = 0 Ohms
C10 = 0 Ohms
C1 – C7
R1, R2
L1 – L3
(I and Q)
LK5 (I and Q)
All = OPEN
LK5x = OPEN
AD8348
相关PDF资料 |
PDF描述 |
|---|---|
| AD8348-EVAL | 50-1000 MHz Quadrature Demodulator |
| AD8348XXX | 50-1000 MHz Quadrature Demodulator |
| AD8349 | 700 MHz to 2700 MHz Quadrature Modulator |
| AD8349ARE | 700 MHz to 2700 MHz Quadrature Modulator |
| AD8349ARE-REEL7 | 700 MHz to 2700 MHz Quadrature Modulator |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD8348ARE | 制造商:Analog Devices 功能描述:QUADRATURE MODULATOR - Rail/Tube |
| AD8348ARU | 功能描述:IC QUADRATUR DEMOD 50MHZ 28TSSOP RoHS:否 类别:RF/IF 和 RFID >> RF 解调器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:解调器 LO 频率:- RF 频率:70MHz ~ 300MHz P1dB:-9dBm 增益:- 噪音数据:6.36dB 电流 - 电源:41.5mA 电源电压:2.7 V 封装/外壳:28-WFQFN 裸露焊盘 供应商设备封装:28-TQFN-EP（5x5） 包装:带卷 (TR) |
| AD8348ARU-REEL7 | 功能描述:IC QUADRATUR DEMOD 50MHZ 28TSSOP RoHS:否 类别:RF/IF 和 RFID >> RF 解调器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:解调器 LO 频率:- RF 频率:70MHz ~ 300MHz P1dB:-9dBm 增益:- 噪音数据:6.36dB 电流 - 电源:41.5mA 电源电压:2.7 V 封装/外壳:28-WFQFN 裸露焊盘 供应商设备封装:28-TQFN-EP（5x5） 包装:带卷 (TR) |
| AD8348ARUZ | 功能描述:IC QUADRATURE DEMOD 28-TSSOP RoHS:是 类别:RF/IF 和 RFID >> RF 解调器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:解调器 LO 频率:- RF 频率:70MHz ~ 300MHz P1dB:-9dBm 增益:- 噪音数据:6.36dB 电流 - 电源:41.5mA 电源电压:2.7 V 封装/外壳:28-WFQFN 裸露焊盘 供应商设备封装:28-TQFN-EP（5x5） 包装:带卷 (TR) |
| AD8348ARUZ-REEL7 | 功能描述:IC QUADRATURE DEMOD 28-TSSOP TR RoHS:是 类别:RF/IF 和 RFID >> RF 解调器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:解调器 LO 频率:- RF 频率:70MHz ~ 300MHz P1dB:-9dBm 增益:- 噪音数据:6.36dB 电流 - 电源:41.5mA 电源电压:2.7 V 封装/外壳:28-WFQFN 裸露焊盘 供应商设备封装:28-TQFN-EP（5x5） 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。