- 您现在的位置：买卖IC网 > PDF目录373944 > AD8348 (Analog Devices, Inc.) 50-1000 MHz Quadrature Demodulator PDF资料下载
参数资料
| 型号： | AD8348 |
| 厂商： | Analog Devices, Inc. |
| 英文描述： | 50-1000 MHz Quadrature Demodulator |
| 中文描述： | 50-1000兆赫正交解调器 |
| 文件页数： | 8/13页 |
| 文件大小： | 778K |
| 代理商： | AD8348 |
PRELIMINARY TECHNICAL DATA
Applications
Basic Connections
The basic connections described here refer to the AD8348
evaluation board. The schematic for the evaluation board is
shown in Figure 1.
Power Supply
The voltage supply for the AD8348, between 2.7V and 5V,
should be connected to the +Vs test point and ground should
be connected to one of the GND test points.
Device Enable
To enable the device, the pin ENBL should be driven to +Vs.
Grounding the same pin will disable the device. On the
evaluation board this can be achieved by moving SW11 to the
ENBL and DENBL positions respectively.
VGA Enable
The VGA can be enabled by driving the voltage on the pin
ENVG to +Vs. In this mode, the MX inputs are disabled and
the IF inputs should be utilized. Grounding the pin will
disable the VGA and the IF inputs. When the VGA is
disabled the MX inputs should be used. On the evaluation
board, SW12 should be positioned in either the IF or MX
positions.
Gain Control
When the VGA is enabled, the gain can be controlled by the
voltage on pin VGIN. The gain control voltage range is
between 0.2 V and 1.2 V. This corresponds to a gain range
between 25.6 dB and –18.3 dB. For convenience, a
potentiometer R15 is provided to allow for changes in gain
without the need for an additional DC voltage source. To use
the potentiometer, the switch SW13 must be set to the POT
position. Alternatively, an external voltage applied to either
the testpoint or SMA connector labeled VGIN can set the
gain. SW13 must be set to the EXT position when an external
gain control voltage is used.
Rev. PrF 2/11/03
- 8 -
LO Input
The local oscillator signal should be fed to the SMA connector
J21. This port is terminated in 50 Ohms. The recommended
LO drive level is between –10 and 0 dBm. The LO frequency
at the input to the device should be twice that of the desired
LO frequency at the mixer core. The applied LO frequency
range is between 100 MHz and 2 GHz.
IF Input
The IF input should be fed into the SMA connector IFIP. The
VGA must be enabled when this port is used (SW12 in the IF
position).
MX Input
The input to the mixer input can be either single-ended or
differential. The evaluation board is, by default, set for
single-ended MX drive. To change to a differential drive, T41
should be removed along with resistor R42. DC blocking
capacitors (C42, C43) should be installed in place of T41.
This will present a nominal differential impedance of 200
Ohms (100 Ohms each side). The differential inputs should
then be fed into SMA connectors MXIP and MXIN.
Baseband Outputs
The baseband outputs are at the IOPP, IOPN, QOPP and
QOPN testpoints and SMA connectors. These outputs are not
designed to drive 50 Ohm loads directly and should be
presented with loads of at least 2k Ohms.
Output DC Bias Level
The DC bias level of the baseband amplifier outputs are by
default tied to Vref through LK11. If desired, the DC bias
level can be changed by removing LK11 and driving a DC
voltage onto either the VCMO testpoint.
AD8348
相关PDF资料 |
PDF描述 |
|---|---|
| AD8348-EVAL | 50-1000 MHz Quadrature Demodulator |
| AD8348XXX | 50-1000 MHz Quadrature Demodulator |
| AD8349 | 700 MHz to 2700 MHz Quadrature Modulator |
| AD8349ARE | 700 MHz to 2700 MHz Quadrature Modulator |
| AD8349ARE-REEL7 | 700 MHz to 2700 MHz Quadrature Modulator |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD8348ARE | 制造商:Analog Devices 功能描述:QUADRATURE MODULATOR - Rail/Tube |
| AD8348ARU | 功能描述:IC QUADRATUR DEMOD 50MHZ 28TSSOP RoHS:否 类别:RF/IF 和 RFID >> RF 解调器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:解调器 LO 频率:- RF 频率:70MHz ~ 300MHz P1dB:-9dBm 增益:- 噪音数据:6.36dB 电流 - 电源:41.5mA 电源电压:2.7 V 封装/外壳:28-WFQFN 裸露焊盘 供应商设备封装:28-TQFN-EP（5x5） 包装:带卷 (TR) |
| AD8348ARU-REEL7 | 功能描述:IC QUADRATUR DEMOD 50MHZ 28TSSOP RoHS:否 类别:RF/IF 和 RFID >> RF 解调器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:解调器 LO 频率:- RF 频率:70MHz ~ 300MHz P1dB:-9dBm 增益:- 噪音数据:6.36dB 电流 - 电源:41.5mA 电源电压:2.7 V 封装/外壳:28-WFQFN 裸露焊盘 供应商设备封装:28-TQFN-EP（5x5） 包装:带卷 (TR) |
| AD8348ARUZ | 功能描述:IC QUADRATURE DEMOD 28-TSSOP RoHS:是 类别:RF/IF 和 RFID >> RF 解调器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:解调器 LO 频率:- RF 频率:70MHz ~ 300MHz P1dB:-9dBm 增益:- 噪音数据:6.36dB 电流 - 电源:41.5mA 电源电压:2.7 V 封装/外壳:28-WFQFN 裸露焊盘 供应商设备封装:28-TQFN-EP（5x5） 包装:带卷 (TR) |
| AD8348ARUZ-REEL7 | 功能描述:IC QUADRATURE DEMOD 28-TSSOP TR RoHS:是 类别:RF/IF 和 RFID >> RF 解调器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:解调器 LO 频率:- RF 频率:70MHz ~ 300MHz P1dB:-9dBm 增益:- 噪音数据:6.36dB 电流 - 电源:41.5mA 电源电压:2.7 V 封装/外壳:28-WFQFN 裸露焊盘 供应商设备封装:28-TQFN-EP（5x5） 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。